ECA EIA-364-42C-2012 TP-42C IMPACT TEST PROCEDURE FOR ELECTRICAL CONNECTORS.pdf

1、 EIA STANDARD TP-42C IMPACT TEST PROCEDURE FOR ELECTRICAL CONNECTORS EIA-364-42C (Revision of EIA-364-42B) April 2012 EIA Standards Electronic Components Industry AssociationEIA-364-42CANSI/EIA-364-42C-2012 Approved: April 16, 2012 NOTICE EIA Engineering Standards and Publications are designed to se

2、rve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Sta

3、ndards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than ECIA members

4、, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any liability to any patent owner, nor does it assume an

5、y obligation whatever to parties adopting the Standard or Publication. This standard is based upon the major technical content of International Electrotechnical Commission standard 60512-7-2, mechanical strength impact, 1992-08. It conforms in all essential respects this IEC standard. This Standard

6、does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (

7、From Standards Proposal No. SP-5229 formulated under the cognizance of the CE-2.0 National Connector Standards Committee). Published by ELECTRONIC COMPONENTS INDUSTRY ASSOCIATION 2012 Engineering Department 2214 Rock Hill Road, Suite 170 Herndon, VA 20170 PLEASE ! DONT VIOLATE THE LAW! This document

8、 is copyrighted by the ECIA and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information, contact: IHS 15 Inverness Way East Englewood, CO 80112-5704 or call USA and Canada (1-800-

9、854-7179), International (303-397-7956) i CONTENTS Clause Page 1 Introduction . 1 1.1 Scope . 1 1.2 Object 1 2 Test resources 1 2.1 Equipment . 1 3 Test specimen 1 3.1 Description 1 3.2 Preparation 2 4 Test procedure . 2 5 Details to be specified . 3 6 Test documentation . 3 Table 1 Drop height and

10、number of drops . 2 Figure 1 Typical test fixture 4 2 Impact test procedure, see table 1 . 4 ii (This page left blank) EIA-364-42C Page 1 TEST PROCEDURE No. 42C IMPACT TEST PROCEDURE FOR ELECTRICAL CONNECTORS (From EIA Standards Proposal No. 5229, formulated under the cognizance EIA CE-2.0 Committee

11、 on National Connector Standards, and previously published in EIA-364-42B.) 1 Introduction 1.1 Scope This standard establishes a method to determine the effects of impacts on electrical connectors. 1.2 Object The object of this test procedure is to determine the ability of a connector to withstand i

12、mpacts of the type that might be encountered when a connector is dropped to the floor. This test should only be performed on connectors designed to meet such requirements. 2 Test resources 2.1 Equipment 2.1.1 A test fixture similar to that shown in figure 1 shall be used. Unless otherwise specified,

13、 this fixture shall be capable of being mounted to any convenient, rigid, vertical structure at a height of 0.6 meter (2 feet). 2.1.2 The impact surface shall be a concrete floor or a concrete slab at least 0.1 meter (4 inches) thick. 3 Test specimen 3.1 Description A test sample shall consist of a

14、plug, or a receptacle, or a mated plug and receptacle, as specified in the referencing document. EIA-364-42C Page 2 3.2 Preparation The test sample shall be wired as intended for normal service, complete with accessories. Unless otherwise specified, the combined length of the pipe fixture and the co

15、nnector cable shall be 2.1 meters 25 millimeters (7 feet 1 inch) with a minimum length of 457 millimeters (18 inches) of cable. In the case of a mated sample, the connector on the free end shall be wired with 152 millimeters (6 inches) of leads. 4 Test procedure 4.1 The cable, with the sample attach

16、ed, shall be securely fastened to the test fixture such that the cable assembly can hang freely. 4.2 Unless otherwise specified, the cable assembly shall be extended its full length from the test fixture to a drop height that is specified in table 1. Drop requirements shall be determined by the serv

17、ice class of the test sample. The sequence and number of drops shall be as indicated in table 1. The test sample shall fall by the pendulum action of the pipe and cable assembly and strike the impact pad. The radial orientation for each series of eight drops shall be dictated by using the index feat

18、ure of the test fixture. Each drop shall originate from a different index position. Table 1 - Drop height and number of drops Drop height Service class Light Moderate Severe 2.4 meters (8 feet ) - 8 8 1.8 meters (6 feet ) 8 - 8 1.2 meters (4 feet ) - 8 8 0.6 meter (2 feet ) - - 8 0.1 meter (4 inch )

19、 - - 8 Total drops 8 16 40 4.3 Failures Potential modes of failure resulting from this test are inability to mate or unmate, broken parts or accessories, electrical failure, damage to seals. EIA-364-42C Page 3 5 Details to be specified The following details shall be specified in the referencing docu

20、ment: 5.1 Length of pipe and cable, if other than specified in 3.2 5.2 Drop height, if other than specified in 4.2 5.3 Number of impacts, if other than specified in table 1 5.4 Number of samples to be tested 5.5 Sample description (plug, receptacle, mated, unmated, etc.) 5.6 Acceptance criteria 5.7

21、Service class 6 Test documentation Documentation shall contain the details specified in clause 5, with any exceptions, and the following: 6.1 Title of test 6.2 Sample description; including fixturing 6.3 Test equipment used, and date of last and next calibration 6.4 Test procedure 6.5 Values and obs

22、ervation 6.6 Name of operator and start/finish date(s) of test EIA-364-42C Page 4 Figure 1 - Typical test fixture Figure 2 - Impact test procedure, see table 1 ECIA Document Improvement Proposal If in the review or use of this document, a potential change is made evident for safety, health or techni

23、cal reasons, please fill in the appropriate information below and mail or FAX to: Electronic Components Industry Association Technology Strategy & Standards Department Publications Office 2214 Rock Hill Road, Suite 170 Herndon, VA 20170 FAX: (571-323-0245) Document No.: Document Title: Submitters Na

24、me: Telephone No.: FAX No.: e-mail: Address: Urgency of Change: Immediate: At next revision: Problem Area: a. Clause Number and /or Drawing: b. Recommended Changes: c. Reason/Rationale for Recommendation: Additional Remarks: Signature: Date: FOR ECIA USE ONLY Responsible Committee: Chairman: Date co

25、mments forwarded to Committee Chairman: Revision History Revision letter Project number Additions, changes and deletions C SP-5229 Revised format to comply with current practices in conjunction with 5 year review. Revision contains no technical changes. Electronic Components Industry Association 2214 Rock Hill Road, Suite 170 * Herndon, VA 20170-4212 * tel 571-323-0294 * fax 571-323-0245 www.eciaonline.org