ECA EIA-364-58A-2003 TP-58A Temperature Life with Mechanical Loading for Connectors with Removable Contacts (Static Mechanical Load at Temperature) Test Procedure for Electrical Co.pdf

1、 EIA STANDARD TP-58A Temperature Life with Mechanical Loading for Connectors with Removable Contacts (Static Mechanical Load at Temperature) Test Procedure for Electrical Connectors EIA-364-58A (Revision of EIA-364-58) July 2003 Electronic Components Industry Association ANSI/EIA-364-58A-2003 (R2016

2、) Approved: August 7, 2003 Reaffirmed: April 13, 2016 EIA-364-58A NOTICE EIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and a

3、ssisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and

4、Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than ECIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National S

5、tandards Institute (ANSI) patent policy. By such action, ECIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA standard is considered to have International Standardization implications, but the Int

6、ernational Electrotechnical Commission activity has not progressed to the point where a valid comparison between the EIA standard and the IEC document can be made. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is t

7、he responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. SP-4918-A and reaffirmed by Standards Proposal No. 5361.03, formulated under the cognizance of

8、 the EIA CE-2.0 Committee on National Connector and Socket Standards). Published by ELECTRONIC COMPONENTS INDUSTRY ASSOCIATION 2016 Standards initial and post test 5.5 Load conditions (static) 5.6 Observations and measurement to be made before and after testing EIA-364-58A Page 4 6 Test documentatio

9、n Documentation shall contain the details specified in clause 5, with any exceptions, and the following: 6.1 Title of test 6.2 Specimen description, including fixturing 6.3 Test equipment used, and date of last and next calibration 6.4 Values and observations 6.4.1 Visual examination 6.4.2 Monitorin

10、g measurements as specified in the referencing document 6.5 Contact locations before after test 6.6 Name of operator and date of test ECIA Document Improvement Proposal If in the review or use of this document, a potential change is made evident for safety, health or technical reasons, please fill i

11、n the appropriate information below and mail or FAX to: Electronic Components Industry Association EIA Standards & Technology Department 2214 Rock Hill Rd., Suite 265 Herndon, VA 20170 FAX: (571-323-0245) Document No.: Document Title: Submitters Name: Telephone No.: FAX No.: e-mail: Address: Urgency

12、 of Change: Immediate: At next revision: Problem Area: a. Clause Number and /or Drawing: b. Recommended Changes: c.Reason/Rationale for Recomendation: Additional Remarks: Signature: Date: FOR ECIA USE ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: Revision History Revision letter Project number Publication date Additions, changes and deletions Electronic Components Industry Association 2214 Rock Hill Road, Suite 265 * Herndon, VA 20170 * tel 571-323-0294 * fax 571-323-0245 www.ecianow.org