ECA EIA-364-68A-2001 TP-68A Actuating Mechanism Test Procedure for Electrical Connectors.pdf

1、 EIA STANDARD TP-68A Actuating Mechanism Test Procedure for Electrical Connectors EIA-364-68A (Revision of EIA-364-68) April 2001 ANSI/EIA-364-68A-2001(R2015) Approved: April 10, 2001 Reaffirmed: March 24, 2015 EIA-364-68ANOTICE EIA Engineering Standards and Publications are designed to serve the pu

2、blic interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards and

3、 Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than ECIA members, whether

4、the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any liability to any patent owner, nor does it assume any obligati

5、on whatever to parties adopting the Standard or Publication. This standard is based upon the major technical content of International Electrotechnical Commission standard 512-5, test 8c, robustness of activating lever, 1992-08, second edition. It conforms in all essential respects to this IEC standa

6、rd. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations

7、 before its use. (From Standards Proposal No. 4897, formulated under the cognizance of the CE-2.0 Committee on EIA National Connector and Socket Standards, and reaffirmed per Standards Proposal No. 5346.04). Published by Electronic Components Industry Association 2015 Standards see figure 1 for exam

8、ple force details. The force shall be applied in each of the following directions. - Fal/Fa2 perpendicular to the actuator axis and in the plane of the actuator travel and at each end position of the actuator; - Fbl/Fb2 perpendicular to the actuator axis and perpendicular to the plane of actuator tr

9、avel at each end position of the lever; axially with the lever axis towards the lever pivot; and axially with the lever axis away from the lever pivot. - Fc - Fd 4. .2 The force shall be steadily increased at a rate of approximately 20 N/s (, 50 lb/s) up to the specified value and maintained for 1 m

10、inute unless otherwise specified in the referencing document. 4.2 Torque A specified torque shall be applied around the axis of the lever in either direction for 1 minute, unless otherwise specified in the referencing document. 5 Details to be specified The following details shall be specified in th

11、e referencing document: 5.1 Mounting details 5.2 Shape of the fixture or tool for the application of the forcekorque 5.3 Forcekorque to be applied, direction and rate of application 5.4 Requirements for final measurements 5.5 Any deviation from this standard EN-3 64-68A Page 3 6 Test documentation D

12、ocumentation shall contain the details specified in clause 5, with any exceptions, and the following: 6.1 Title of test 6.2 Specimen description 6.3 Test equipment used, and date of last and next calibration 6.4 Test and procedure 6.5 Values and observations 6.6 Name of operator and date of test Fd

13、Lever pivot point Side view i w l Actuating lever axis I End view i Figure 1 Details of force application ECIA Document Improvement Proposal If in the review or use of this document, a potential change is made evident for safety, health or technical reasons, please fill in the appropriate informatio

14、n below and mail or FAX to: Electronic Components Industry Association EIA Standards & Technology Department 2214 Rock Hill Rd., Suite 265 Herndon, VA 20170 FAX: (571-323-0245) Document No.: Document Title: Submitters Name: Telephone No.: FAX No.: e-mail: Address: Urgency of Change: Immediate: At ne

15、xt revision: Problem Area: a. Clause Number and /or Drawing: b. Recommended Changes: c. Reason/Rationale for Recommendation: Additional Remarks: Signature: Date: FOR ECIA USE ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: Electronic Components Industry Association 2214 Rock Hill Road, Suite 265 * Herndon, VA 20170 * tel 571-323-0294 * fax 571-323-0245 www.ecianow.org