ECA EIA-364-75A-2009 TP-75A Lightning Strike Test Procedure for Electrical Connectors.pdf

1、 EIA STANDARD TP-75A Lightning Strike Test Procedure for Electrical Connectors EIA-364-75A (Revision of EIA-364-75) January 2009 ANSI/EIA-364-75A-2009(R2015) Approved: January 13, 2009 Reaffirmed: March 24, 2015 EIA-364-75ANOTICE EIA Engineering Standards and Publications are designed to serve the p

2、ublic interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards an

3、d Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than ECIA members, whether

4、 the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any liability to any patent owner, nor does it assume any obligat

5、ion whatever to parties adopting the Standard or Publication. This EIA standard is considered to have International Standardization implication, but the International Electrotechnical Commission activity has not progresses to the point where a valid comparison between the EIA Standard and the IEC do

6、cument can be made. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regula

7、tory limitations before its use. (From Standards Proposal No. 5175, formulated under the cognizance of the CE-2.0 Committee on EIA National Connector and Socket Standards, and reaffirmed per Standards Proposal No. 5346.06). Published by Electronic Components Industry Association 2015 Standards the t

8、orque that shall be applied to facilitate full coupling and uncoupling shall be measured and recorded. 5.1.3 Shell-to-shell conductance Mated connectors shall be subjected to the test specified in EIA-364-83. 5.1.4 Lightning strike Mated connectors with suitable accessories shall be subjected to a s

9、imulated lightning current pulse exposure. Test currents are provided in table 1 and table 2. The simulated current pulse shall be applied between the plug accessory braid and the receptacle mounting panel. Upon completion of the pulse application, perform shell-to-shell conductance test. When the e

10、lectrical measurements have been completed, the specimen shall be visually inspected in both the mated and unmated condition for evidence of damage from the simulated lightning current. Remate the plug and receptacle following the inspection and repeat the shell-to-shell conductance test. EIA-364-75

11、A Page 7 5.1.5 Dielectric withstanding voltage Wired, unmated connectors shall be tested in accordance with EIA-364-20. 5.1.6 Post test visual examination The tested specimens shall be visually examined for any evidence of damage that could impair proper functioning. 6 Details to be specified The fo

12、llowing detail shall be specified in the referencing document: 6.1 Test level, including lightning characterization levels, and type A or B waveform 6.2 Dielectric withstanding voltage test parameters, as specified in EIA-364-20. 6.3 Points of measurement for shell conductance 6.4 Number and polarit

13、y of simulated lightning strikes . 6.5 Information to prepare the specimens for test 6.6 Coupling torque, if applicable 6.7 Specified visual examination requirements, if applicable EIA-364-75A Page 8 7 Test documentation Documentation shall contain the details specified in clause 5, with any excepti

14、ons, and the following: 7.1 Title of test 7.2 Specimen description and part number 7.3 Test equipment used, and date of last and next calibration 7.4 Peak current 7.5 Plots or photograph(s) of waveform 7.6 Test data 7.7 Test observations 7.8 Test conditions; e.g., temperature and humidity 7.9 Test s

15、pecimen preparation and fixturing methods 7.10 Dielectric withstanding voltage and conductance parameters 7.11 Name of operator and start/finish date(s) of test EIA-364-75A Page 9 Figure 1 - Direct attachment waveform Where: Component A (First return stroke) Peak amplitude: 200kA (10%) Action integr

16、al : 2 x 106A2s (20%) (in 500s) Time duration: 500s Component B (Intermediate current) Maximum charge transfer: 10 coulombs (10%) Avenge amplitude: 2kA (20%) Time duration: 5ms Component C (Continuing current) Amplitude: 200 - 800A Charge transfer: 200 coulombs (20%) Time duration: 0.25 to 1s Compon

17、ent D (Subsequent return stroke) Peak Amplitude: 100kA (10%) Action Integral: 0.25 x 106A2s (20%) (in 500s) Duration: 500s EIA-364-75A Page 10 Figure 2 - Indirect effects waveform Figure 3 - Lightning test setup EIA-364-75A Page A-1 Annex A References (informative) The following references(s) are no

18、t required for this test method; however they may provide useful information to the user. Electronic Industries Association EIA-622, Glossary of Electrical Connector Related Terms Military MIL-STD-464, Electromagnetic Environmental Effects MIL-STD-810, Environmental Engineering Considerations And La

19、boratory Tests Radio Technical Commission for Aeronautics (RTCA) DO-160, Environmental Conditions and Test Procedures for Airborne Equipment SAE International (SAE) SAE ARP5412, Aircraft Lightning Environment and Related Test Waveforms SAE ARP5414, Aircraft Lightning Zoning SAE ARP5416, Aircraft Lig

20、htning Test Methods Revision History Revision letter Project number Additions, changes and deletions A SP-5175 Revised all paragraphs ECIA Document Improvement Proposal If in the review or use of this document, a potential change is made evident for safety, health or technical reasons, please fill i

21、n the appropriate information below and mail or FAX to: Electronic Components Industry Association EIA Standards & Technology Department 2214 Rock Hill Rd., Suite 265 Herndon, VA 20170 FAX: (571-323-0245) Document No.: Document Title: Submitters Name: Telephone No.: FAX No.: e-mail: Address: Urgency

22、 of Change: Immediate: At next revision: Problem Area: a. Clause Number and /or Drawing: b. Recommended Changes: c. Reason/Rationale for Recommendation: Additional Remarks: Signature: Date: FOR ECIA USE ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: Electronic Components Industry Association 2214 Rock Hill Road, Suite 265 * Herndon, VA 20170 * tel 571-323-0294 * fax 571-323-0245 www.ecianow.org