ECA EIA-364-98-1997 TP-98 Housing Locking Mechanism Strength Test Procedure for Electrical Connectors.pdf

1、 EIA STANDARD TP-98 Housing Locking Mechanism Strength Test Procedure for Electrical Connectors EIA-364-98 June 1997 ANSI/EIA-364-98-1997(R2015) Approved: May 8, 1997 Reaffirmed: March 24, 2015 EIA-364-98NOTICE EIA Engineering Standards and Publications are designed to serve the public interest thro

2、ugh eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards and Publications shal

3、l not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than ECIA members, whether the standard is to

4、 be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to par

5、ties adopting the Standard or Publication. This EIA standard is considered to have International Standardization implication, but the International Electrotechnical Commission activity has not progresses to the point where a valid comparison between the EIA Standard and the IEC document can be made.

6、 This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations be

7、fore its use. (From Standards Proposal No. 3812, formulated under the cognizance of the CE-2.0 Committee on EIA National Connector and Socket Standards, and reaffirmed per Standards Proposal No. 5347.03). Published by Electronic Components Industry Association 2015 Standards & Technology Department

8、2214 Rock Hill Road, Suite 265 Herndon, VA 20170 PLEASE! DONT VIOLATE THE LAW! This document is copyrighted by the ECIA and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information

9、, contact: IHS 15 Inverness Way East Englewood, CO 80112-5704 or call USA and Canada (1-877-413-5184), International (303-397-7956) CONTENTS Clause 1 2 2.1 3 4 4.1 4.2 4.3 4.4 5 6 Introduction Test resources Equipment Test specimen . Test procedure Mounting Preparation . Force application Failure mo

10、de . Details to be specified . Test documentation 1 1 1 2 1 - STD-EIA 3b9-78-ENGL 1977 W 3234b00 0583977 O78 EIA-3 64-98 Page 1 TEST PROCEDURE No. 98 HOUSING LOCKING MECHAMSM STRENGTH TEST PROCEDURE FOR ELECTRICAL CONNECTORS 1 Introduction This specification describes a test procedure for determinin

11、g the mechanical retention strength of the locking retention features of mated plastic connector housings. 2 Test resources 2.1 Equipment Apparatus shall include the following: 2.1.1 housings. Clamps, jaw or other fixtures to hold the respective halves of the mated connector 2.1.2 13 millimeters per

12、 minute (0.5 inch per minute). Force mechanism capable of separating the holding devices at a constant rate of 2.1.3 Gage or recorder capable of measuring the axial force to within an accuracy of 2 2%. 3 Test specimen Sizes fiom the connector family shall be chosen as specified in the Detail Specifi

13、cation. 4 Test procedure 4.1 Preparation Connector housings, without contacts, shall be mated. Check that the latches are properly and fully engaged. 4.2 Mounting Mated connector housings shall be placed on appropriate fixtures on force application mechanism. One fixture should be ked and the opposi

14、te fixture floating (or self-aligning) to ensure that the applied force is along one axis. Previous page is blank EIA-364-98 Page 2 4.3 Force application The force mechanism shall be set to exert an axial force at a constant rate of 13 millimeters per minute (0.5 inch per minute) to separate the hou

15、sing halves. 4.4 Data to be recorded Maximum force and visual observations shall be recorded. 5 Details to be specified The following details shall be specified in the Detail Specification: 5.1 Size and number of housings to be tested. 5.2 Minimum locking strength force. 5.3 Sequence of conditioning

16、 and testing, if applicable. 5.4 Conditions if other than standard atmospheric conditions. 5.5 Rate of force application, if different than the value specified in 4.3. 5.6 Special fixturing requirements, if applicable. 6 Test documentation Documentation shall contain the following: 6.1 Title of test

17、. 6.2 Description of specimen and fixture. 6.3 Test equipment used. 6.4 Values and observations. 6.5 Ambient temperature and humidity. 6.6 Name of operator and date of test. ECIA Document Improvement Proposal If in the review or use of this document, a potential change is made evident for safety, he

18、alth or technical reasons, please fill in the appropriate information below and mail or FAX to: Electronic Components Industry Association EIA Standards & Technology Department 2214 Rock Hill Rd., Suite 265 Herndon, VA 20170 FAX: (571-323-0245) Document No.: Document Title: Submitters Name: Telephon

19、e No.: FAX No.: e-mail: Address: Urgency of Change: Immediate: At next revision: Problem Area: a. Clause Number and /or Drawing: b. Recommended Changes: c. Reason/Rationale for Recommendation: Additional Remarks: Signature: Date: FOR ECIA USE ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: Electronic Components Industry Association 2214 Rock Hill Road, Suite 265 * Herndon, VA 20170 * tel 571-323-0294 * fax 571-323-0245 www.ecianow.org