ECA EIA-520E000-A-2000 Sectional Specification In-Line Switches of Certified Quality.pdf

1、ANSI/EIA-520E000-A-2000 Approved: October 25,2000 EIA SPECIFICATION Sectional Specification In-Line Switches of Certified Quality EIA-520E000-A (Revision of EU-520E000) OCTOBER 2000 ELECTRONIC COMPONENTS, ASSEMBLIES degradations are not permitted. 2 General 2.1 Related Documents The following docume

2、nts of the issue in effect form a part of this specification to the extent specified herein: EIA-5200000 Generic Specification for Special Use Electromechanical Switches of Certified Quality 2.2 Terminology Terminology shall be in accordance with EIA-5200000. Terminology peculiar to detail specifica

3、tion shall be defined in those documents. Terminology peculiar to the products covered by this specification shall be defined herein. 2.3 Preferred Ratings and Characteristics Whenever possible, the values, ratings, and characteristics shall be selected from the following: 2.3.1 Preferred ratings: T

4、he electrical ratings shall be as specified in detail specifications EIA-520E000-A Page 2 2.3.1.1 Rated Voltage; The following voltage ratings are preferred; 50 V dc, 6 V dc, 20 mV dc. 2.3.1.2 Rated Current; The following current ratings are preferred; 250 mA, 100 mA, 10 mA. 2.3.2 Preferred Characte

5、ristics; 2.3.2.1 Low Temperature Rating; The following low temperature ratings are preferred; -10 OC, -25 OC, -40 OC, -55 OC. 2.3.2.2 High Temperature ratings; The following high temperature ratings are preferred; 55 OC, 70 OC, 85 oC,lOO OC, 125 OC. 2.5 Marking The switches shall be marked with the

6、following information; a) terminal or actuator identification whenever specified in b) Manufacturers name, trademark, or code identification C) Identifying number (EIA part number, manufacturers part d) Date code - the date code is a four digit number consisting the detail specification. number. num

7、ber, or users part number. of the last two digits of the year and another two digits for the week of the year. Foe example; a date code of 8822 denotes the 22nd week of 1988. Other markings may be applied to the switch provided they do not interfere with, obscure, or confuse those markings specified

8、 above. Where size, surface condition, or other design considerations will not allow full marking of the part, the markings shall be in the order of preference shown above. Any required markings which cannot be applied to the switch shall be applied to the package containing the switch. 2.6 Informat

9、ion to be Given in the Detail Specification Detail specifications shall be derived from thee relevant Blank Detail Specification and shall contain all the required information. Detail specifications shall not specify requirements inferior to those of the generic or Sectional specifications. When mor

10、e severe requirements are included, they shall be listed in the detail specification and indicated in the test schedule with an asterisk (for example). The detail specification shall contain the complete technical requirements for the inspection including the quality conformance test schedule. If th

11、e technical requirements of the generic and/or Sectional specification relative to inspection are not entirely suitable (either for technical reasons or for special applications) to the component described in the detail specification, the detail specification shall set out clearly the various amendm

12、ents which are to be made to those requirements. EIA-520E000-A Page 3 3 OUALITY ASSESSMENT PROCEDURES 3.1 Qualification Approval Procedures The qualification approval procedures shall be in accordance with EIA- 5200000 and the following additional requirements; 3.1.1 Qualification inspection tests;

13、The qualification inspection tests are described in table I herein. The minimum qualification inspection for any in- line switch shall be Groups A and B in Table I. Additional Test Groups C, D and E may be added to the qualification requirements for a specific detail specification as necessary, as c

14、an test beyond those of Table I. When Test Groups C through E are prescribed by the detail specification, the identity of the Test Group, the sequence of tests, and the minimum sample quantity shall be in accordance with Table I. When the detail specification prescribes tests not in Table I, the add

15、itional tests shall be included within existing Test Groups or as additional Test Groups. 3.2 3.3 3.4 3.5 4 4.9 4.24 Primary Stage of Manufacture The primary stage of manufacture is as prescribed in EIA-5200000. Structurally Similar Switches Structurally similar switches shall be prescribed in EIA-5

16、200000. Quality Conformance Inspection Quality conformance inspection shall be as prescribed in EIA-5200000 and the following requirements; 3.4.1 Lot-by-lot Inspection Tests; The lot-by-lot inspection tests are prescribed in Table II herein unless otherwise specified in the detail specification. 3.4

17、.2 Periodic inspection tests; The periodic inspection tests are as prescribed in Table III herein. Alternate Test Methods Alternative test methods shall be prescribed in EIA-5200000. TEST AND MEASUREMENT PROCEDURES This Section supplements the test methods and requirements of EIA- 5200000. Strength

18、of Terminations Terminals shall withstand the application of a 0.5 kilogram (12 pound) load in tensile. The bending test shall be in accordance with the Tag Termination Test except that the terminals shall be bent 22.5 forward from the normal position, 45 backward through the normal position, and 22

19、.5 forward, returning to the normal position. If the bending method is not critical, the bending shall be done with the fingers. If the bending method is critical, appropriate fixturing may be used for precise control of the point of application of force and angles of bending. Machine Soldering The

20、machine soldering test shall be in accordance with EIA 448, Method 16. EIA-520E000-A Page 4 TABLEI: OUALIFICATION APPROVAL INSPECTION TESTS TEST Method and Group MJWS DJND t.s. t.d. g.d. Test No. Group A M Visual Examination 1-1 M ND All O O Dimensions 1-2 M ND (1) 0 Mass 1-4 M ND (1) 0 Switch Resis

21、tance 2-1 M ND All O Insulation Resistance 2-5 M ND All O Voltage Proof 3-1 M ND All O Group B M 10 Solderability 11-1 M D 1 Strength of Terminations(see 4.9) M D 1 Electrical Endurance 8 M D 1 Switch Resistance 2-1 M ND 1 Voltage Proof 3-1 M ND 1 1 Group C Machine Soldering ws (2) (2) see 4.24 MIA

22、D (2) Visual Examination 1-1 MIA ND (2) Switch Resistance 2-1 MIA ND (2) Insulation Resistance 2-5 MIA ND (2) Group D Thermal Shock Vibration Visual Examination Shock Visual Examination Switch resistance Voltage Proof ws 10-2 MIA D 5-3 MIA D 1-1 MIA ND 5-2 MIA D 1-1 MIA ND 2-1 MIA ND 3-1 MIA ND Grou

23、p E ws (2) (2) Capacitance 17-1 MIA ND (2) Moisture Resistance 10-1 MIA D (2) Switch Resistance 2-1 MIA ND (2) Voltage Proof 3-1 MIA ND (2) EIA-520E000-A Page 5 TABLE II: LOT-BY-LOT INSPECTION TESTS Assessment Level C Test Method and Group Test No. DJND - IL AQL Group A (Lot-by-lot) Visual Examinati

24、on 1-1 ND Major Minor Switch Resistance 2-1 ND Insulation Resistance 2-5 ND Voltage Proof 3-1 ND II 1% Table III: OERIODIC INSPECTION TESTS DJND t.s. t.d. g.d. - Test Method and Group Test No. Group B (every 12 months Solderability 11-1 D Strength of Terminations See 4.9 D Electrical Endurance 8 D S

25、witch Resistance 2-1 ND Voltage Proof 3-1 ND Groux C everv 36 months) 20 1 - - - Requalification Table I D KEY: M = mandatory test WS = when specified test MIA = mandatory test if applicable (i.e., test is mandatory if D = destructive test ND = non-destructive test t.s.= minimum quantity of test spe

26、cimens t.d = maximum permissible number defective units per test g.d. = maximum permissible number of defective units per group If test group is specified NOTES (l)=A minimum of 2 pieces of each configuration covered by the Detail Specification (2)=See Detail Specification EIA Document Improvement P

27、roposal If in the review or use of this document, a potential change is made evident for safety, health or technical reasons, please fill in the appropriate information below and mail or FAX to: Electronic Industries Alliance Engineering Department - Publications Office 2500 Wilson Blvd. Arlington,

28、VA 22201 FAX: (703) 907-7501 Document No. Submitters Name: Address: Document Title: Telephone No.: FAX No.: e-mail: Urgency of Change: Immediate: 0 At next revision: 0 Problem Area: a. Clause Number and/or Drawing: c. Reasoflationale for Recommendation: Additional Remarks: Signature: Date: FOR EIA USE ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: Electronic Industries Alliance