ECA EIA-60115-9-1-2014 Fixed Resistors for Use in Electronic Equipment - Part 9-1 Blank Detail Specification Fixed Surface Mount Resistor Networks with Individually Measurable Resi.pdf

1、 EIA STANDARD Fixed Resistors for Use in Electronic Equipment Part 9-1: Blank Detail Specification: Fixed Surface Mount Resistor Networks with Individually Measurable Resistors Assessment Level EZ EIA-60115-9-1 (IEC 60115-9-1:2003, IDT) October 2014 ANSI/EIA-60115-9-1-2014 Approved: October 6, 2014

2、EIA-60115-9-1NOTICE EIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining wit

3、h minimum delay the proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standar

4、ds and Publications preclude their voluntary use by those other than ECIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such acti

5、on, ECIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Standard is identical (IDT) with the International Standard IEC Publication 60115-9-1:2003: Fixed Resistors for Use in Electronic Equipment

6、 Part 9-1: Blank Detail Specification: Fixed Surface Mount Resistor Networks with Individually Measurable Resistors Assessment Level EZ. This document is the EIA Standard EIA-60115-9-1: 2014: Fixed Resistors for Use in Electronic Equipment Part 9-1: Blank Detail Specification: Fixed Surface Mount Re

7、sistor Networks with Individually Measurable Resistors Assessment Level EZ. The text, figures and tables of IEC 60115-9-1:2003 are used in this Standard with the consent of the IEC and the American National Standards Institute (ANSI). The IEC copyrighted material has been reproduced with permission

8、from ANSI. The IEC Foreword and Introduction are not part of the requirements of this standard but are included for information purposes only. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of

9、the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 5314, formulated under the cognizance of the Steering Committee for Passive Electronic Components Standards (S-1).

10、Published by Electronic Components Industry Association 2014 Standards any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation.

11、IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of

12、opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made

13、to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transpare

14、ntly to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be ren

15、dered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of

16、its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any o

17、ther IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be t

18、he subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60115-9-1 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. This bilingual version (2012-09) corresponds to the m

19、onolingual English version, published in 2003-10. The text of this standard is based on the following documents: FDIS Report on voting 40/1345/FDIS 40/1367/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. EIA-6011

20、5-9-1 Page 2 The French version of this standard has not been voted upon. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site

21、under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. EIA-60115-9-1 Page 3 INTRODUCTION Blank detail specification A blank detail specification is a supplementary documen

22、t to the sectional specification and contains requirements for style, layout and minimum content of detail specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with IEC specifications nor shall they be so described. In the preparati

23、on of detail specifications the content of 1.4 of the sectional specification shall be taken into account. The numbers between square brackets on the first page of the detail specification correspond to the following information which shall be inserted in the position indicated. Identification of th

24、e detail specification 1 The “International Electrotechnical Commission“ or the National Standards Organization under whose authority the detail specification is drafted. 2 The IEC or National Standards number of the detail specification, date of issue and any further information required by the nat

25、ional system. 3 The number and issue number of the IEC or national generic specification. 4 The IEC number of the blank detail specification. Identification of the resistor network 5 A short description of the type of resistor network. 6 Information on typical construction (when applicable). 7 Outli

26、ne drawing with main dimensions which are of importance for interchangeability and/or reference to the national or international documents for outlines. Alternatively, this drawing may be given in an annex to the detail specification. 8 Application or group of applications covered and/or assessment

27、level. 9 Reference data on the most important properties, to allow comparison between the various resistor network types. EIA-60115-9-1 Page 4 1 IEC 60115-9-1-XXX 2 QC 400701XXXXXX ELECTRONIC COMPONENTS OF ASSESSED QUALITY IN ACCORDANCE WITH: 3 IEC 60115-9-1 4 QC 400701 FIXED SURFACE MOUNT RESISTOR

28、NETWORKS WITH 5 INDIVIDUALLY MEASURABLE RESISTORS Outline drawing: (see Table 1) (. angle projection) 7 (Other shapes are permitted within the dimensions given) 6 Assessment level: EZ 8 NOTE For 1 to 9: see previous page. 9 Information on the availability of components qualified to this detail speci

29、fication is given in the IEC QC 001005 EIA-60115-9-1 Page 5 FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT Part 9-1: Blank detail specification: Fixed surface mount resistor networks with individually measurable resistors Assessment level EZ 1 General data 1.1 Dimensions, ratings and characteristic

30、s Table 1 Styles related to dimensions, ratings and characteristics Style Rated element dissipation at 70 C a)W Rated network dissipation at 70 C W Limiting element voltage (DC or AC r.m.s.) V Insulation voltage against ambientV Insulation voltage between neighbouring resistors V Dimensions mm L W T

31、 A B P a)The detail specification shall specify the conditions under which the rated dissipation applies. Resistance range1 to Tolerances on rated resistance % Climatic category / Stability class % Limits for change of resistance: for long-term tests ( %R + ) for short-term tests ( %R + ) Temperatur

32、e coefficient : 106/K _ 1The preferred values are those of the E24 and E96 series of IEC 60063. EIA-60115-9-1 Page 6 1.1.1 Derating Resistors covered by this specification are derated according to the following curve: (A suitable curve to be included in the detail specification) NOTE See also 2.2.3

33、of the sectional specification. 1.2 Recommended method(s) of mounting (to be inserted) (See 1.4.2 of IEC 60115-9.) 1.3 Related documents Generic specification IEC 60115-1:1999, Fixed resistors for use in electronic equipment Part 1: Generic specification Sectional specification IEC 60115-9:2003, Fix

34、ed resistors for use in electronic equipment Part 9: Sectional specification: Fixed surface mount resistor networks with individually measurable resistors 1.4 Marking The marking of the resistors and the package shall be in accordance with the requirements of 2.4 of IEC 60115-1 and 1.4.5 of IEC 6011

35、5-9. The details of the marking of the component and packaging shall be given in full in the detail specification. 1.5 Ordering information Orders for resistors covered by this specification shall contain, in clear or in coded form, the following minimum information: a) rated element resistance; b)

36、tolerance on rated resistance; c) number and issue reference of the detail specification and style reference; d) packaging instructions. 1.6 Certified records of released lots Required/non required. 1.7 Additional information (not for inspection purposes) 1.8 Additional or increased severities or re

37、quirements to those specified in the generic and/or sectional specification NOTE Additions or increased requirements should be specified only when essential. EIA-60115-9-1 Page 7 2 Inspection requirements 2.1 Procedures 2.1.1 For qualification approval, the procedure shall be in accordance with 3.2

38、of IEC 60115-9. 2.1.2 For quality conformance inspection, the test schedule (Table 2) includes sampling, periodicity, severities and requirements. The formation of inspection lots is covered by 3.3.1 of IEC 60115-9. The following list applies to the test schedules developed in Table 2 and Table 3. a

39、) Subclause numbers of tests and performance requirements refer to the generic specification, IEC 60115-1, except for resistance change requirements, which shall be selected from Table 3 of IEC 60115-9, as appropriate. b) Number to be tested: sample size as directly allotted to the code letter for I

40、L in Table IIA of IEC 60410 (single sampling plan for normal inspection). c) In these tables: p is the periodicity (in months) n is the sample size c is the acceptance criterion (permitted number of non-conforming items) D indicates a destructive test ND indicates a non-destructive test IL is the in

41、spection level d) 100 % testing shall befollowed by re-inspection by sampling in order to monitor outgoing quality level by non-conforming items per million (ppm). The sampling level shall be established by the manufacturer. For the calculation of 106values, any parametric failure shall be counted a

42、s a non-conforming item. In case one or more non-conforming items occur in a sample, this lot shall be rejected. e) If one non-conforming item is obtained, all the tests of the subgroup shall be repeated on a new sample and then no further non-conforming items are permitted. Release of product may c

43、ontinue during repeat testing. EIA-60115-9-1 Page 8 Table 2 Test schedule for quality conformance inspection: lot-by-lot Subclause number and test (see 2.1.2, list item a of this specification) D or ND Conditions of test (see 2.1.2, list item a of this specification) IL n c Performance requirements

44、see 2.1.2, list item a of this specification) (see 2.1.2, list item c of this specification) GROUP A INSPECTION (lot-by-lot) Subgroup A0 4.5 Resistance ND 100 % (see 2.1.2, list item d of this specification) As in 4.5.2 Subgroup A1 4.4.1 Visual examination 4.4.2 Dimensions (gauging) ND S-4 1)0 As i

45、n 4.4.1 As specified in the detail specification GROUP B INSPECTION (lot-by-lot) Subgroup B1 4.7 Voltage proof (insulated resistors only) Voltage proof between neighbouring resistors ND Method: Insulation resistance (insulated resistors only) Voltage: V S-3 1)0 As in 4.7.3 100 M As in 4.7.3 Subgroup

46、 B2 4.17 Solderability D Aging, if applicable S-3 1)0 As in 4.17.5 Subgroup B3 4.31 Mounting 4.13 Overload (in the mounted state) D Substrate material and spacing: see 2.3.2 of IEC 60115-9 The applied voltage shall be 2,5 times the rated voltage or twice the limiting element voltage, whichever is th

47、e less severe Duration: 2 s S-3 1)0 Visual examination Resistance No visible damage R ( %R + ) 4.30 Solvent resistance of the marking (if applicable) Solvent: Solvent temperature: Method 1 Rubbing material: cotton wool Recovery: Legible marking 1)See 2.1.2, list item b of this specification.EIA-6011

48、5-9-1 Page 9 Table 3 Test schedule for quality conformance inspection: periodic Subclause number and test (see 2.1.2, list item a of this specification) D or ND Conditions of test (see 2.1.2, list item a of this specification) Sample size & criterion of acceptability (see 2.1.2, list item c of this

49、specification) Performance requirements (see 2.1.2, list item a of this specification) p n c1)GROUP C INSPECTION (periodic) Subgroup C1 4.31 Mounting 4.33 Substrate bending test D Substrate material: Resistance 3 20 0 R ( %R + ) 4.33.6 Final Inspection Visual examination No visible damage Subgroup C2 4.18 Resistance to soldering heat 4.29 Component solvent resistance D Visual examination Resistance Solvent: Solvent temperature: