ECA EIA-60384-26-1-2014 Fixed Capacitors for Use in Electronic Equipment C Part 26-1 Blank Detail Specification C Fixed Aluminium Electrolytic Capacitors with Conductive Polymer So.pdf

1、 EIA STANDARD Fixed Capacitors for Use in Electronic Equipment Part 26-1: Blank Detail Specification Fixed Aluminium Electrolytic Capacitors with Conductive Polymer Solid Electrolyte Assessment Level EZ EIA-60384-26-1 (IEC 60384-26-1:2010, IDT) September 2014 ANSI/EIA-60384-26-1-2014 Approved: Septe

2、mber 30, 2014 EIA-60384-26-1 NOTICE EIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting a

3、nd obtaining with minimum delay the proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence

4、 of such Standards and Publications preclude their voluntary use by those other than ECIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent poli

5、cy. By such action, ECIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Standard is identical (IDT) with the International Standard IEC Publication 60384-26-1:2010: Fixed Capacitors for Use in El

6、ectronic Equipment Part 26-1: Blank Detail Specification Fixed Aluminium Electrolytic Capacitors with Conductive Polymer Solid Electrolyte Assessment Level EZ. This document is the EIA Standard EIA-60384-26-1-2014 Edition 1: Fixed Capacitors for Use in Electronic Equipment Part 26-1: Blank Detail Sp

7、ecification Fixed Aluminium Electrolytic Capacitors with Conductive Polymer Solid Electrolyte Assessment Level EZ. The text, figures and tables of IEC 60384-26-1:2010 are used in this Standard with the consent of the IEC and the American National Standards Institute (ANSI). The IEC copyrighted mater

8、ial has been reproduced with permission from ANSI. The IEC Foreword and Introduction are not part of the requirements of this standard but are included for information purposes only. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory re

9、quirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 5266, formulated under the cognizance of the P-2.5 Committee on EIA Solid E

10、lectrolytic Capacitors Standards and given final approval by the Standards Steering Committee for Passive Electronic Components Standards (S-1). Published by Electronic Components Industry Association 2014 Engineering Department 2214 Rock Hill Road, Suite 265 Herndon, VA 20170 PLEASE! DONT VIOLATE T

11、HE LAW! This document is copyrighted by the ECIA and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information, contact: IHS 15 Inverness Way East Englewood, CO 80112-5704 or call U

12、SA and Canada (1-877-413-5184), International (303-397-7956) i CONTENTS FOREWORD 1 1 General data 4 1.1 Recommended method(s) of mounting (to be inserted) 4 1.2 Dimensions . 4 1.3 Rating and characteristics 5 1.4 Normative references 5 1.5 Marking . 6 1.6 Ordering information 6 1.7 Certified records

13、 of released lots 6 1.8 Additional information (not for inspection) . 6 1.9 Other requirements for generic or sectional specifications . 6 2 Inspection requirements . 6 2.1 Procedures . 6 2.1.1 Qualification approval . 6 2.1.2 Quality conformance inspection 6 Bibliography . 15 Table 1 Case size refe

14、rence and dimensions 4 Table 2 Values of capacitance and of voltage related to case sizes 5 Table 3 Characteristics 5 Table 4 Other requests (other characteristics) . 6 Table 5 Test schedule for quality conformance inspection 7 EIA-60384-26-1 Page 1 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIXED

15、CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 26-1: Blank detail specification Fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte Assessment level EZ FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization compr

16、ising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Stand

17、ards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this prepa

18、ratory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organiz

19、ations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of

20、 recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation

21、 by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or region

22、al publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by

23、 independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees fo

24、r any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Nor

25、mative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held resp

26、onsible for identifying any or all such patent rights. International Standard IEC 60384-26-1 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment The text of this standard is based on the following documents: FDIS Report on voting 40/2053/FDIS 40/2063/RV

27、D Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. EIA-60384-26-1 Page 2 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of the IEC 60384 series can be found, u

28、nder the general title Fixed capacitors for use in the electronic equipment, on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the speci

29、fic publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. EIA-60384-26-1 Page 3 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 26-1: Blank detail specification Fixed aluminium electrolytic capacitors with conductive polymer solid

30、 electrolyte Assessment level EZ Blank detail specification A blank detail specification is a supplementary document to the sectional specification and contains requirements for style and layout and minimum content of detail specifications. Detail specifications not complying with these requirements

31、 may not be considered as being in accordance with IEC specification nor shall they so be described. In the preparation of detail specifications the contents of 1.4 of the sectional specification shall be taken into account. The numbers between brackets on the first page correspond to the following

32、information which shall be inserted in the position indicated. Identification of the detail specification 1 The “International Electrotechnical Commission” or the National Standards Organization under whose authority the detail specification is drafted. 2 The IEC or National Standards number of the

33、detail specification, date of issue and any further information required by the national system. 3 The number and date of issue of the IEC or National Generic Specification. 4 The number of the IEC or National blank detail specification. Identification of the capacitor 5 A short description of the t

34、ype of capacitor. 6 Information on typical construction (If applicable). 7 Outline drawing with main dimensions which are of importance for interchange ability and / or reference to the national or international documents for outlines. Alternatively, this drawing may be given in an appendix to the d

35、etail specification. 8 Application or group of applications covered and / or assessment level. 9 Reference data on the most important properties, to allow comparison between the various capacitor types. EIA-60384-26-1 Page 4 12ELECTRONIC COMPONENTS OF ASSESSED QUALITY IN ACCORDANCE WITH: 3 4 IEC 603

36、84-26-1 5 Aluminium electrolytic capacitors with conductive polymer solid electrolyte Outline drawing: (see Table 1) ( angle projection) 7 6 8 Assessment level(s): EZ Information on the availability of components qualified to this detail specification is given in the qualified product list. 9 1 Gene

37、ral data 1.1 Recommended method(s) of mounting (to be inserted) See IEC 60384-26, 1.4.2 1.2 Dimensions Table 1 Case size reference and dimensions Dimensions in millimeters Case size reference L W H d NOTE 1 When there is no case-size reference, decline Table 1 and give the dimensions in Table 2 as T

38、able 1. NOTE 2 Indicate the dimensions as maximum dimension or as nominal dimensions with tolerance. EIA-60384-26-1 Page 5 1.3 Rating and characteristics Ratings and characteristics are as listed below. Nominal capacitance range (see Table 2) Tolerance on nominal capacitance Rated voltage (see Table

39、 2) Climatic category Rated temperature Rated ripple current (see Table 3) Tangent of loss angle (see Table 3) Leakage current (see Table 3) Equivalent series resistance (see Table 3) Reverse voltage (if required in the detail specification) Table 2 Values of capacitance and of voltage related to ca

40、se sizes Rated voltage Nominal capacitance Case size Case size Case size Case size Case size Table 3 Characteristics URCNTangent of loss angle at C, . Hz Leakage current at C Equivalent series resistance at C, Hz Rated ripple current at C, Hz V F Hz A mA or A 1.4 Normative references The following r

41、eferenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60068-2-20:2008, Environmental testing Part 2-20: Tests Test

42、 T Test methods for solderability and resistance to soldering heat of devices with leads IEC 60384-1:2008, Fixed capacitors for use in electronic equipment Part 1: Generic specification EIA-60384-26-1 Page 6 IEC 60384-26:1Fixed capacitors for use in electronic equipment Part 26: Sectional specificat

43、ion Fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte 1.5 Marking The marking of the capacitor and the package shall be in accordance with the requirements of IEC 60384-26, 1.6. NOTE The details of the marking of the component and package should be given in full in th

44、e detail specification. 1.6 Ordering information Orders for capacitors covered by this specification shall contain, in clear or in coded form, the following minimum information: a) nominal capacitance; b) tolerance on nominal capacitance; c) rated d.c. voltage; d) issue number and edition of the det

45、ail specification and type of capacitors. 1.7 Certified records of released lots Required / not required NOTE Clearly state a necessity for customer requests. 1.8 Additional information (not for inspection) NOTE Clearly state a necessity for additional information. 1.9 Other requirements for generic

46、 or sectional specifications NOTE Other requirements should be specified to those that are absolutely necessary. See Table 4. Table 4 Other requests (other characteristics) This table is to be used for defining characteristics which are additional to, or more severe than, those given in the sectiona

47、l specification. 2 Inspection requirements 2.1 Procedures 2.1.1 Qualification approval For qualification approval, the procedures shall be in accordance with IEC 60384-26, 3.4. 2.1.2 Quality conformance inspection For quality conformance inspection, the test schedule (Table 5) includes sampling, per

48、iodicity, severities and requirements. The formation of inspection lots is covered by IEC 60384-26, 3.5.1. 1To be published. EIA-60384-26-1 Page 7 Table 5 Test schedule for quality conformance inspection Subclause number and test aD or ND bTest condition aSample number and criteria cRequirements aIL

49、 n c Group A inspection (each lot) Subgroup A0 4.22 High surge current ND 100 %dSee detail specification 4.4.1 Leakage current Protective resistor: 1 000 0,2 CNUR(A) or 500 A (whichever is greater) 4.4.2 Capacitance Frequency: Hz Bias voltage: V Within specified tolerance 4.4.3 Tangent of loss angle (tan ) Frequency: Hz Bias voltage: V See Table 3 4.4.4 Equivalent series resistance (ESR) Frequency: 100