ECA EIA-60938-2-2-2014 Fixed Inductors for Electromagnetic Interference Suppression - Part 2-2 Blank Detail Specification - Inductors for Which Safety Tests Are Required (Only).pdf

1、 EIA STANDARD Fixed Inductors for Electromagnetic Interference Suppression Part 2-2: Blank Detail Specification Inductors for Which Safety Tests Are Required (Only) EIA-60938-2-2 (IEC 60938-2-2:1999, IDT) July 2014 EIA-60938-2-2 ANSI/EIA-60938-2-2-2014 Approved: July 28, 2014 NOTICE EIA Engineering

2、Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product f

3、or his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their v

4、oluntary use by those other than ECIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any liabili

5、ty to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Standard is identical (IDT) with the International Standard IEC Publication 60938-2-2:1999: Fixed Inductors for Electromagnetic Interference Suppression Part 2-2: Blank Detail

6、 Specification Inductors for Which Safety Tests Are Required (Only). This document is the EIA Standard EIA-60938-2-2-2014 Edition 1: Fixed Inductors for Electromagnetic Interference Suppression Part 2-1: Blank Detail Specification Inductors for Which Safety Tests Are Required (Only). The text, figur

7、es and tables of IEC 60938-2-2:1999 are used in this Standard with the consent of the IEC and the American National Standards Institute (ANSI). The IEC copyrighted material has been reproduced with permission from ANSI. The IEC Foreword and Introduction are not part of the requirements of this stand

8、ard but are included for information purposes only. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to deter

9、mine the applicability of regulatory limitations before its use. (From Standards Proposal No. 5304, formulated under the cognizance of the Steering Committee for Passive Electronic Components Standards (S-1). Published by Electronic Components Industry Association 2014 Engineering Department 2214 Ro

10、ck Hill Road, Suite 265 Herndon, VA 20170 PLEASE! DONT VIOLATE THE LAW! This document is copyrighted by the ECIA and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information, conta

11、ct: IHS 15 Inverness Way East Englewood, CO 80112-5704 or call USA and Canada (1-877-413-5184), International (303-397-7956) i Contents 1 General data 4 1.1 Recommended method(s) of mounting (to be inserted) . 4 1.2 Dimensions . 5 1.3 Ratings and characteristics 5 d.c. resistance related to type des

12、ignation 5 1.4 Related documents 5 1.5 Marking . 6 1.6 Ordering information 6 1.7 Additional information (not for inspection purposes) . 6 1.8 Additional or increased severities or requirements to those specified in the generic or sectional specification . 6 2 Inspection requirements . 6 2.1 Procedu

13、res 6 2.2 Test schedules 6 2.2.1 Initial approval . 6 2.2.2 Conformance tests . 6 Table 1 Dimensions related to case size 5 Table 2 Values of inductance, rated current and . 5d.c. resistance related to type designation 5 Table 3 Other characteristics . 6 Table 4 Conformance tests 7 Annex A (normativ

14、e) Declaration of design . 8 EIA-60938-2-2 Page 1 1 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION Part 2-2: Blank detail specification Inductors for which safety tests are required (only) FOREWORD 1) The IEC (International Electrotechnical C

15、ommission) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end an

16、d in addition to other activities, the IEC publishes International Standards. Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizatio

17、ns liaising with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of the IEC on technical

18、 matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested National Committees. 3) The documents produced have the form of recommendations for international use and are published in the

19、 form of standards, technical specifications, technical reports or guides and they are accepted by the National Committees in that sense. 4) In order to promote international unification, IEC National Committees undertake to apply IEC International Standards transparently to the maximum extent possi

20、ble in their national and regional standards. Any divergence between the IEC Standard and the corresponding national or regional standard shall be clearly indicated in the latter. 5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment d

21、eclared to be in conformity with one of its standards. 6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights. International Standard IE

22、C 60938-2-2 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. This bilingual version (2013-05) corresponds to the monolingual English version, published in 1999-10. The text of this standard is based on the following documents: FDIS Report on voting

23、40/1113/FDIS 40/1139/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. The French version of this standard has not been voted upon. This publication has been drafted in accordance with the ISO/IEC Directives, Part

24、3. Annex A forms an integral part of this standard. EIA-60938-2-2 Page 2 The committee has decided that this publication remains valid until 2005. At this date, in accordance with the committees decision, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. EIA-

25、60938-2-2 Page 3 3 FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION Part 2-2: Blank detail specification Inductors for which safety tests are required (only) INTRODUCTION Blank detail specification This blank detail specification forms the basis for a uniform procedure for a common mark.

26、 It implements the approval schedule for safety tests only in IEC 60938-2, requires a declaration of design for parameters relevant to safety tests and prescribes conformance tests to be conducted on every lot prior to its release and re-qualification tests depending on changes of the design. In com

27、parison with IEC 60938-2-1 which provides safety tests and performance tests, this specification is restricted to safety tests only. The use of IEC 60938-2-1 may be more appropriate for components manufactured in mass production, whereas this specification may be necessary in those cases where appro

28、val and re-qualification tests contribute considerably to the costs of the product. A blank detail specification is a supplementary document to the sectional specification and contains requirements for style and layout and minimum content of detail specifications. In the preparation of detail specif

29、ications the content of 1.4 of the sectional specification shall be taken into account. The numbers between square brackets on the first page of the detail specification correspond to the following information which shall be inserted in the position indicated. Identification of the detail specificat

30、ion and of the inductor The first page of the detail specification should have the layout recommended on the next page of this blank detail specification. 0 Manufacturers name. 0A Manufacturers style designation. 1 The “International Electrotechnical Commission“ or the National Standards Organisatio

31、n under whose authority the detail specification is drafted. 2 The IEC or National Standards number of the detail specification, date of issue and any further information required by the national system. 3 The number and issue number of the IEC or national generic specification. 4 The IEC number of

32、the blank detail specification. Identification of the inductor 5 A short description of the inductor or range of inductors. 6 Information on typical construction (when applicable). EIA-60938-2-2 Page 4 7 Outline drawing with main dimensions which are of importance for interchangeability and/or refer

33、ence to the national or international documents for outlines. Alternatively, this drawing may be given in an annex to the detail specification, but should always contain an illustration of the general outer appearance of the inductor. 8 Reference data on the most important properties, to allow compa

34、rison between the various inductor types intended for the same, or for similar applications. 1 IEC 60938-2-1XX 2 QC XXXXXXXXXXXXELECTRONIC COMPONENTS OF ASSESSED IEC 60938-2-2 4 QUALITY IN ACCORDANCE WITH: QC XXXXXX 3 FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION FOR WHICH SAFETY 5 Ou

35、tline drawing: (see table 1) TESTS ARE REQUIRED (. angle projection) 7 6 (Other shapes are permitted within the dimensions given) Safety tests only 8NOTES 1 to 9 see pages 3 and 4. Information on the availability of components qualified to this detail specification is given in the Register of Approv

36、als. 1 General data 1.1 Recommended method(s) of mounting (to be inserted) (See 1.4.3 of IEC 60938-2.) EIA-60938-2-2 Page 5 5 1.2 Dimensions Table 1 Dimensions related to case size Case size reference or type Dimensions mm L1W H L2L3L4NOTE 1 When there is no case size reference, the dimensions shoul

37、d be given per type designation. NOTE 2 The dimensions should be given as maximum dimensions or as nominal dimensions with a tolerance. 1.3 Ratings and characteristics Rated inductance (LR) (see table 2) Tolerance on rated inductance Rated current (I) range (see table 2) DC resistance (R) (see table

38、 2) Rated voltage Rated temperature Climatic category Category of passive flammability (if applicable) Table 2 Values of inductance, rated current and d.c. resistance related to type designation Ordering code, type designation LR per line mH IR A Rmaxper line 1.4 Related documents Generic specificat

39、ion: IEC 60938-1:1999, Fixed inductors for electromagnetic interference suppression Part 1: Generic specification Sectional specification: IEC 60938-2:1999, Fixed inductors for electromagnetic interference suppression Part 2: Sectional specification EIA-60938-2-2 Page 6 1.5 Marking The marking of th

40、e inductor shall be in accordance with the requirements of 1.6 of IEC 60938-2. The details of the marking of the component and package shall be given in full in the detail specification. 1.6 Ordering information Orders for inductors covered by this specification shall contain, in clear or in coded f

41、orm, the following minimum information: a) type designation; b) rated inductance; c) tolerance on rated inductance; d) rated voltage; e) rated current; f) number and issue reference of the detail specification and style reference. 1.7 Additional information (not for inspection purposes) 1.8 Addition

42、al or increased severities or requirements to those specified in the generic or sectional specification NOTE Additions or increased requirements should be specified only when essential. Table 3 Other characteristics This table is to be used for defining characteristics which are additional to or mor

43、e severe than those given in the sectional specification. 2 Inspection requirements 2.1 Procedures For qualification approval, the procedures shall be in accordance with 3.4 of IEC 60938-2. 2.2 Test schedules 2.2.1 Initial approval See table 1 and annex A of the sectional specification. 2.2.2 Confor

44、mance tests See table 4 of this specification in association with annex A of this specification. 2.2.2.1 Conformance tests (lot-by-lot) EIA-60938-2-2 Page 7 7 Table 4 Conformance tests Subclause number and test (see note 1) D or ND (see note 3) Conditions of test (see note 1) Sample size Requirement

45、s (see note 1) 4.4 Inductance 4.1 Visual examination 4.2 Voltage proof ND 100 % (see note 2) Within specified tolerance Legible marking and as specified in 1.5 of this specification No permanent breakdown or flashover NOTE 1 Clause numbers of test and performance requirements refer to the sectional

46、specification, IEC 60938-2 and clause 1 of this specification. NOTE 2 May be carried out as end-of-line testing. NOTE 3 D = destructive ND = non destructive 2.2.2.2 Re-qualification Re-qualification tests according to 2.2.1 may be required by the certification body when a change of the declared desi

47、gn as given in annex A is intended. The certification body shall be informed about the intended change(s) and shall decide whether re-qualification tests have to be performed. As a maximum, a complete re-qualification according to 2.2.1 may be necessary. (See also introduction.) EIA-60938-2-2 Page 8

48、 Annex A (normative) Declaration of design (Confidential to the manufacturer and the certification body) The purpose of this description is to register essential data and the basic design of the inductors for which approval is sought. The completed form shall be submitted to the relevant certificati

49、on body prior to any approval testings; its circulation to the other parties is left to the decision of the manufacturer. Changes of the declared design are permitted only after notifying the certification body in writing. In this case the certification body will decide on necessary steps to be taken. As a maximum, a complete re-qualification may be required. Registration number: (to be allocated by the certification body) 1 Applicant: 2 Manufacturer: 3 Manufacturing site: 4