ECMA 148-1997 Private Itegrated Services Network (PISN) - Specification Functional Model and Information Flows - Identification Supplementary Services (3rd Edition)《专用综合业务网络(PISN) .pdf

1、Standard ECMA-1483rd Edition - June 1997Standardizing Information and Communication SystemsPhone: +41 22 849.60.00 - Fax: +41 22 849.60.01 - URL: http:/www.ecma.ch - Internet: helpdeskecma.chPrivate Integrated Services Network(PISN) -Specification, Functional Model andInformation Flows -Identificati

2、on Supplementary Services.Standard ECMA-1483rd Edition - June 1997Standardizing Information and Communication SystemsPhone: +41 22 849.60.00 - Fax: +41 22 849.60.01 - URL: http:/www.ecma.ch - Internet: helpdeskecma.chIW E-148iii.doc 14-08-97 09,17Private Integrated Services Network(PISN) -Specificat

3、ion, Functional Model andInformation Flows -Identification Supplementary Services(ISSD).Brief HistoryThis Standard is one of a series of ECMA Standards defining services and signalling protocols applicable to Private IntegratedServices Networks (PISNs). The series uses ISDN concepts as developed by

4、ITU-T and conforms to the framework ofInternational Standards for Open Systems Interconnection as defined by ISO/IEC. It has been produced under ITSTC workitem M-IT-05 2.2.1 for Bon de Commande 76B/D.1 and under ETSI work item RE/ECMA-00139.This particular Standard specifies the Identification suppl

5、ementary services (Calling Line Identification Presentation,Connected Line Identification Presentation, and Calling/Connected Line Identification Restriction), which allow a userinvolved in a call to receive information concerning the identity (number and subaddress) of the other user in the call. I

6、naddition a user can prevent the presentation of his number to other users. Corresponding services are specified for publicISDNs in CCITT recommendations I.251 and Q.81 (1992), and annex A to this Standard provides a comparison.This Standard is based upon the practical experience of ECMA member comp

7、anies and the results of their active andcontinuous participation in the work of ISO/IEC JTC1, ITU-T, ETSI and other international and national standardizationbodies. It represents a pragmatic and widely based consensus.Compared to the 1st and 2nd Editions of Standard ECMA-148 (published by ECMA in

8、December 1990 and June 1993respectively), this 3rd Edition incorporates changes in order to achieve complete alignment with International StandardISO/IEC 14136:1995(E) published by ISO/IEC in June 1995.Adopted as 3rd Edition of Standard ECMA-148 by the General Assembly of June 1997.- i -Table of con

9、tents1 Scope 12 Conformance 13 References (normative) 14 Definitions 24.1 External definitions 24.2 Other definitions 24.2.1 Calling user number 24.2.2 Calling user subaddress 24.2.3 Connected user 24.2.4 Connected user number 24.2.5 Connected user subaddress 25 Acronyms 26 SS-CLIP stage 1 specifica

10、tion 36.1 Description 36.1.1 General description 36.1.2 Qualifications on applicability to telecommunication services 36.2 Procedure 36.2.1 Provision/withdrawal 36.2.2 Normal procedures 36.2.3 Exceptional procedures 46.3 Interaction with other supplementary services and ANFs 46.3.1 Connected Line Id

11、entification Presentation (SS-COLP) 46.3.2 Calling/Connected Line Identification Restriction (SS-CLIR) 46.4 Interworking considerations 46.4.1 Incoming calls 46.4.2 Outgoing calls 46.5 Overall SDL 47 SS-COLP stage 1 specification 67.1 Description 67.1.1 General description 67.1.2 Qualifications on a

12、pplicability to telecommunication services 67.2 Procedure 67.2.1 Provision/withdrawal 67.2.2 Normal procedures 67.2.3 Exceptional procedures 67.3 Interaction with other supplementary services and ANFs 77.3.1 Calling Line Identification Presentation (SS-CLIP) 7- ii -7.3.2 Calling/Connected Line Ident

13、ification Restriction (SS-CLIR) 77.4 Interworking considerations 77.4.1 Outgoing calls 77.4.2 Incoming calls 77.5 Overall SDL 78 SS-CLIR stage 1 specification 98.1 Description 98.1.1 General description 98.1.2 Qualifications on applicability to telecommunication services 98.2 Procedure 98.2.1 Provis

14、ion/withdrawal 98.2.2 Normal procedures 98.2.3 Exceptional procedures 98.3 Interaction with other supplementary services and ANFs 108.3.1 Calling Line Identification Presentation (SS-CLIP) 108.3.2 Connected Line Identification Presentation (SS-COLP) 108.4 Interworking considerations 108.4.1 Incoming

15、 calls 108.4.2 Outgoing calls 108.5 Overall SDL 109 SS-CLIP stage 2 specification 129.1 Functional model 129.1.1 Functional model description 129.1.2 Description of functional entities 129.1.3 Relationship of functional model to basic call functional model 129.2 Information flows 139.2.1 Definition

16、of information flows 139.2.2 Relationship of information flows to basic call information flows 139.2.3 Examples of information flow sequences 149.3 Functional entity actions 149.3.1 Functional entity actions of FE1 149.3.2 Functional entity actions of FE2 149.4 Functional entity behaviour 149.4.1 Be

17、haviour of FE1 159.4.2 Behaviour of FE2 169.5 Allocation of functional entities to physical equipment 169.6 Interworking considerations 1610 SS-COLP stage 2 specification 1710.1 Functional model 1710.1.1 Functional model description 1710.1.2 Description of functional entities 1710.1.3 Relationship o

18、f functional model to basic call functional model 17- iii -10.2 Information flows 1810.2.1 Definition of information flows 1810.2.2 Relationship of information flows to basic call information flows 1810.2.3 Examples of information flow sequences 1810.3 Functional entity actions 1910.3.1 Functional e

19、ntity actions of FE1 1910.3.2 Functional entity actions of FE2 1910.4 Functional entity behaviour 1910.4.1 Behaviour of FE1 2010.4.2 Behaviour of FE2 2110.5 Allocation of functional entities to physical equipment 2110.6 Interworking considerations 2111 SS-CLIR stage 2 specification 2211.1 Functional

20、 model 2211.1.1 Functional model description 2211.1.2 Description of functional entities 2211.1.3 Relationship of functional model to basic call functional model 2211.2 Information flows 2311.2.1 Definition of information flows 2311.2.2 Relationship of information flows to basic call information flo

21、ws 2311.2.3 Examples of information flow sequences 2311.3 Functional entity actions 2411.3.1 Functional entity actions of FE1 2411.3.2 Functional entity actions of FE2 2411.4 Functional entity behaviour 2411.4.1 Behaviour of FE1 2511.4.2 Behaviour of FE2 2611.5 Allocation of functional entities to p

22、hysical equipment 2711.6 Interworking considerations 27Annex A - Relationship to corresponding recommendations for public ISDNs 29- iv -.1ScopeThis Standard specifies the following Identification supplementary services: Calling Line Identification Presentation(SS-CLIP), Connected Line Identification

23、 Presentation (SS-COLP) and Calling/Connected Line IdentificationRestriction (SS-CLIR), which are applicable to various basic services supported by Private Integrated ServicesNetworks (PISN). Basic services are specified in ECMA-142.Calling Line Identification Presentation (SS-CLIP) is a supplementa

24、ry service which is offered to the called user andwhich provides the calling users PISN number, and possibly a subaddress, to the called user.Connected Line Identification Presentation (SS-COLP) is a supplementary service which is offered to the calling userand which provides the called (connected)

25、users PISN number, and possibly a subaddress, to the calling user.Calling/connected Line Identification Restriction (SS-CLIR) is a supplementary service offered to a user to restrictpresentation of that users PISN number to another user.Supplementary service specifications are produced in three stag

26、es, according to the method described in ETS 300 387.This Standard contains the stage 1 and stage 2 specifications of SS-CLIP, SS-COLP and SS-CLIR. The stage 1specifications (clauses 6, 7 and 8) specify the supplementary services as seen by users of PISNs. The stage 2specifications (clauses 9, 10 an

27、d 11) identify the functional entities involved in the supplementary services and theinformation flows between them.2 ConformanceIn order to conform to this Standard, a stage 3 Standard shall specify signalling protocols and equipment behaviourthat are capable of being used in a PISN which supports

28、the supplementary services specified in this Standard. Thismeans that, to claim conformance, a stage 3 Standard is required to be adequate for the support of those aspects ofclauses 6, 7 and 8 (stage 1) and clauses 9, 10 and 11 (stage 2) which are relevant to the interface or equipment to whichthe s

29、tage 3 Standard applies.3 References (normative)The following standards contain provisions which, through reference in this text, constitute provisions of this Standard.All standards are subject to revision, and parties to agreements based on this Standard are encouraged to investigate thepossibilit

30、y of applying the most recent editions of the standards indicated below.In the case of references to ECMA Standards that are aligned with ISO/IEC International Standards, the number of theappropriate ISO/IEC International Standard is given in brackets after the ECMA reference.ECMA-142 Private Integr

31、ated Services Network - Circuit-mode 64 kbit/s Bearer Services - ServiceDescription, Functional Capabilities and Information Flows (International StandardISO/IEC 11574)ISO/IEC 11571 Information technology - Telecommunications and information exchange between systems -Numbering and sub-addressing in

32、private integrated services networksISO/IEC 11579-1 Information technology - Telecommunications and information exchange between systems -Private Integrated Services Network - Part 1: Reference configuration for PISN Exchanges(PINX)ETS 300 387 Private Telecommunication Network (PTN); Method for the

33、specification of basic andsupplementary services (1994)ITU-T Rec. I.112 Vocabulary of terms for ISDNs (1993)ITU-T Rec. I.210 Principles of telecommunication services supported by an ISDN and the means to describe them(1993)ITU-T Rec. Z.100 Specification and description language (1993)- 2 -4 Definiti

34、onsFor the purposes of this Standard, the following definitions apply.4.1 External definitionsThis Standard uses the following terms defined in other documents: Basic service (ITU-T Rec. I.210) PISN number (ISO/IEC 11571) Private Integrated Services Network (PISN) (ISO/IEC 11579-1) Private Integrate

35、d Services Network Exchange (PINX) (ISO/IEC 11579-1) Service (ITU-T Rec. I.112) Signalling (ITU-T Rec. I.112) Subaddress (ISO/IEC 11571) Supplementary Service (ITU-T Rec. I.210) User (ECMA-142)This Standard refers to the following basic call functional entities (FEs) defined in ECMA-142: Call Contro

36、l (CC) Call Control Agent (CCA)This Standard refers to the following basic call inter-FE relationships defined in ECMA-142: r1 r2 r3This Standard refers to the following basic call information flows defined in ECMA-142: Setup request/indication Setup response/confirmation.4.2 Other definitions4.2.1

37、Calling user numberThe PISN number of the calling user.4.2.2 Calling user subaddressThe subaddress supplied by the calling user for identification purposes.4.2.3 Connected userThe called user that answers a call.4.2.4 Connected user numberThe PISN number of the connected user for identification purp

38、oses.4.2.5 Connected user subaddressThe subaddress supplied by the connected user.5 AcronymsCC Call Control (functional entity)CCA Call Control Agent (functional entity)CGLI Calling Line Identification- 3 -CN Connected NumberCOLI Connected Line IdentificationCS Connected SubaddressFE Functional Enti

39、tyISDN Integrated Services Digital NetworkON Originating NumberOS Originating SubaddressPINX Private Integrated Services Network ExchangePISN Private Integrated Services NetworkPSTN Public Switched Telephone NetworkRI Restriction IndicatorSS-CLIP Supplementary Service Calling Line Identification Pre

40、sentationSS-CLIR Supplementary Service Calling/Connected Line Identification RestrictionSS-COLP Supplementary Service Connected Line Identification PresentationSDL Specification and Description LanguageTE Terminal Equipment6 SS-CLIP stage 1 specification6.1 Description6.1.1 General descriptionThe PI

41、SN provides the called user with the PISN number of the calling user whenever an incoming call ispresented. The number provided should be sufficient to enable the called user to return the call.The calling user number may be accompanied by the calling user subaddress.6.1.2 Qualifications on applicab

42、ility to telecommunication servicesSS-CLIP is applicable to all basic services defined in ECMA-142.6.2 Procedure6.2.1 Provision/withdrawalSS-CLIP shall be generally available. There is no need for service profile control.Some users may have a service profile which permits the override of calling lin

43、e identification restriction.6.2.2 Normal procedures6.2.2.1 Activation/deactivation/registration/interrogationSS-CLIP shall be permanently activated. No information needs to be registered with the PISN for thissupplementary service, and therefore interrogation is not applicable.6.2.2.2 Invocation an

44、d operationThe PISN shall provide the called user with the calling user number at the same time as indicating an incomingcall.The number presented shall be accompanied by indications of the numbering plan and type of number, andshould be sufficient to unambiguously identify the calling user.Where th

45、e number presented has been wholly or partially provided by the calling user, it shall be marked “userprovided, verified and passed“. Otherwise it shall be marked “network-provided“.- 4 -If the calling user has also provided a calling user subaddress, it shall be delivered to the called user alongwi

46、th the calling user number.In some cases where calling line identification restriction has been invoked, there may be certain categories ofcalled user that have the service profile to override this restriction and have the calling user number presented,e.g. emergency stations, PISN attendants. In th

47、ese circumstances, presentation shall include an indication thatrestriction has been invoked.6.2.3 Exceptional procedures6.2.3.1 Activation/deactivation/registration/interrogationNot applicable.6.2.3.2 Invocation and operationThere are two exceptions when the calling user number is not presented to

48、the called user: when calling line identification restriction has been invoked (see definition of Calling/Connected LineIdentification Restriction) and the called user does not have the service profile to override this restriction;and when the calling user number is not available, e.g. due to interw

49、orking with the analogue telephonenetwork (PSTN).In such cases the called user shall receive an indication of the situation. In either case the called user canreceive the calling user subaddress, if available.6.3 Interaction with other supplementary services and ANFsInteractions with other supplementary services and ANFs for which PISN standards were available at the time ofpublication of this Standard are specified below.6.3.1 Connected Line Identification Presentation (SS-COLP)No interaction.6.3.2 Calling/Connected Line Identification Restriction (SS-CLIR)The call