EN 10028-6-2017 en Flat products made of steels for pressure purposes - Part 6 Weldable fine grain steels quenched and tempered.pdf

1、Flat products made of steels for pressure purposesPart 6: Weldable fine grain steels, quenched and temperedBS EN 100286:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10028-6 July 2017 ICS 77.140.30; 77.140.50

2、 Supersedes EN 10028-6:2009English Version Flat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered Produits plats en acier pour appareils pression - Partie 6 : Aciers soudable grains fins, tremps et revenus Flacherzeugnisse aus Druckbehltersthle

3、n - Teil 6: Schweigeeignete Feinkornbausthle, vergtet This European Standard was approved by CEN on 7 May 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alt

4、eration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language ma

5、de by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Esto

6、nia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE

7、FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10028-6:2017 ENational foreword

8、This British Standard is the UK implementation of EN 100286:2017. It supersedes BS EN 100286:2009, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee ISE/107, Steels for Pressure Purposes.A list of organizations represented on this committee can be obtain

9、ed on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 87850 3ICS 77.140.30; 77.140.50Compl

10、iance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 100286:2017EUROPE

11、AN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10028-6 July 2017 ICS 77.140.30; 77.140.50 Supersedes EN 10028-6:2009English Version Flat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered Produits plats en acier pour appareils pression - Partie

12、6 : Aciers soudable grains fins, tremps et revenus Flacherzeugnisse aus Druckbehltersthlen - Teil 6: Schweigeeignete Feinkornbausthle, vergtet This European Standard was approved by CEN on 7 May 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the condi

13、tions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists

14、 in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national stand

15、ards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slova

16、kia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means

17、 reserved worldwide for CEN national Members. Ref. No. EN 10028-6:2017 EBS EN 100286:2017EN 10028-6:2017 (E) 2 Contents Page European foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Tolerances on dimensions . 4 5 Calculation of mass . 4 6 Classification and designation .

18、4 6.1 Classification . 4 6.2 Designation . 5 7 Information to be supplied by the purchaser . 5 7.1 Mandatory information 5 7.2 Options 5 7.3 Example for ordering. 5 8 Requirements . 5 8.1 Steelmaking process 5 8.2 Delivery condition 5 8.3 Chemical composition . 6 8.4 Mechanical properties 6 8.5 Surf

19、ace condition 6 8.6 Internal soundness . 6 9 Inspection 6 9.1 Types of inspections and inspections documents . 6 9.2 Tests to be carried out 6 9.3 Retests, sorting and reprocessing . 6 10 Sampling . 6 11 Test methods 6 12 Marking 6 Annex A (informative) Information on weldability . 11 Annex B (infor

20、mative) Changes to the previous version EN 10028-6:2009 . 12 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of Directive 2014/68/EU aimed to be covered . 13 BS EN 100286:2017EN 10028-6:2017 (E) 3 European foreword This document (EN 10028-6:2017) has

21、 been prepared by Technical Committee ECISS/TC 107 “Steels for pressure purposes”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2018 and conflic

22、ting national standards shall be withdrawn at the latest by January 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This documen

23、t supersedes EN 10028-6:2009. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of Directive 2014/68/EU. For relationship with Directive 2014/68/EU, see informative Annex ZA, which is a

24、n integral part of this document. A list of changes between this document and the previous version can be found in Annex B. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgi

25、um, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,

26、 Switzerland, Turkey and the United Kingdom. BS EN 100286:2017EN 10028-6:2017 (E) 4 1 Scope This European Standard specifies the requirements for flat products for pressure equipment made of weldable fine grain steels, quenched and tempered, as specified in Table 1. The requirements in EN 10028-1:20

27、17 also apply. NOTE Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the

28、 other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directi

29、ve 2014/68/EU are satisfied, needs to be done. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition

30、of the referenced document (including any amendments) applies. EN 1011-1:2009, Welding Recommendations for welding of metallic materials Part 1: General guidance for arc welding EN 1011-2:2001, Welding Recommendations for welding of metallic materials Part 2: Arc welding of ferritic steels EN 10020:

31、2000, Definition and classification of grades of steel EN 10028-1:2017, Flat products made of steels for pressure purposes Part 1: General requirements EN 10204:2004, Metallic products Types of inspection documents 3 Terms and definitions For the purposes of this document the terms and definitions g

32、iven in EN 10028-1:2017 apply. 4 Tolerances on dimensions See EN 10028-1:2017. 5 Calculation of mass See EN 10028-1:2017. 6 Classification and designation 6.1 Classification 6.1.1 This document covers the steel grades given in Table 1 in four qualities: a) the basic series (P.Q); b) series with elev

33、ated temperature properties (P.QH); c) series with low temperature properties down to 40 C (P.QL1); BS EN 100286:2017EN 10028-6:2017 (E) 5 d) series with low temperature properties down to 60 C (P.QL2). 6.1.2 In accordance with EN 10020:2000 all the steels specified in this document are alloy specia

34、l steels. 6.2 Designation See EN 10028-1:2017. 7 Information to be supplied by the purchaser 7.1 Mandatory information See EN 10028-1:2017. 7.2 Options A number of options is specified in this document and listed below. Additionally the relevant options of EN 10028-1:2017 apply. If the purchaser doe

35、s not indicate a wish to implement any of these options at the time of enquiry and order, the products shall be supplied in accordance with the basic specification (see also EN 10028-1:2017). 1) providing data on suitable welding conditions (see 8.2.2); 2) mid thickness test pieces for the impact te

36、st (see Clause 10); 3) limitation of copper and/or tin content (see Table 1, footnote c); 4) no option, intentionally left blank; 5) specification of a minimum impact energy of 40 J (see 8.4 and Table 4, footnote a); 6) applicability of elevated temperature values for QL grades (see Table 5, footnot

37、e a). 7.3 Example for ordering 10 plates with nominal dimensions, thickness = 50 mm, width = 2 000 mm, length = 10 000 mm, made of a steel grade with the name P355QL2 and the number 1.8869 as specified in EN 10028-6, inspection certificate 3.1 as specified in EN 10204: 10 plates 50 2 000 10 000 EN 1

38、0028-6 P355QL2 Inspection certificate 3.1 or 10 plates 50 2 000 10 000 EN 10028-6 1.8869 Inspection certificate 3.1. 8 Requirements 8.1 Steelmaking process See EN 10028-1:2017. 8.2 Delivery condition 8.2.1 The products covered by this European Standard shall be supplied in the quenched and tempered

39、condition. BS EN 100286:2017EN 10028-6:2017 (E) 6 8.2.2 Information on weldability are given in Annex A of this standard. 8.3 Chemical composition 8.3.1 The requirements of Table 1 apply for the chemical composition according to the cast analysis. 8.3.2 The product analysis may deviate from the spec

40、ified values of the cast analysis given in Table 1 by the values given in Table 2. 8.4 Mechanical properties The values given in Tables 3 to 5 apply (see also EN 10028-1:2017 and Clause 10). Optionally, a minimum impact energy value of 40 J may be specified for temperatures where lower minimum value

41、s are specified (see Table 4, footnote a). 8.5 Surface condition See EN 10028-1:2017. 8.6 Internal soundness See EN 10028-1:2017. 9 Inspection 9.1 Types of inspections and inspections documents See EN 10028-1:2017. 9.2 Tests to be carried out See EN 10028-1:2017. 9.3 Retests, sorting and reprocessin

42、g See EN 10028-1:2017. 10 Sampling See EN 10028-1:2017. For the impact test, deviating from EN 10028-1:2017, Table 4, footnote g, the preparation of test pieces taken from the mid thickness may be agreed at the time of enquiry and order. In this case, test temperatures and minimum impact energy valu

43、es shall also be agreed. 11 Test methods See EN 10028-1:2017. 12 Marking See EN 10028-1:2017. BS EN 100286:2017EN10028-6:2017(E)7Table1Chemicalcomposition(castanalysis)abSteelgradeMaximumcontents,%bymassSteelnameSteelnumberCSiMnPSNBCrMoCucNbdNiTidVdZrdP355Q1.88660,160,401,500,0250,0100,0150,0050,300

44、,250,300,050,500,030,060,05P355QH1.8867P355QL11.88680,0200,008P355QL21.88690,005P460Q1.88700,180,501,700,0250,0100,0150,0050,500,500,300,051,000,030,080,05P460QH1.8871P460QL11.88720,0200,008P460QL21.88640,005P500Q1.88730,180,601,700,0250,0100,0150,0051,000,700,300,051,500,050,080,15P500QH1.8874P500Q

45、L11.88750,0200,008P500QL21.88650,005P690Q1.88790,200,801,700,0250,0100,0150,0051,500,700,300,062,500,050,120,15P690QH1.8880P690QL11.88810,0200,008P690QL21.88880,005aElementsnotlistedinthistableshallnotbeintentionallyaddedtothesteelwithout theagreementofthepurchaserexceptforfinishingthecast.Allapprop

46、riatemeasuresshall be takentoprevent theadditionfrom scrapand othermaterialsused insteelmakingoftheseelementswhichmayadverselyaffect themechanicalpropertiesand usability.bThemanufacturermayaddoneorseveralalloyingelement(s)upto themaximum valuesspecified intheorderasafunctionoftheproduct thicknessand

47、 thesteelmakingconditionsinorderto attainthespecifiedproperties.cAlowermaximum coppercontent and/oramaximum sum ofcopperand tincontent,e.g.Cu+6Sn0,33%,maybeagreedupon atthetimeofenquiryandorder,e.g.withregardto hot formability.dThepercentageofgrainrefiningelementsshall beatleast0,015%.Aluminium isal

48、so included intheseelements.Theminimum content of0,015%appliesheretodissolved aluminium.Thisvalueisregarded asattained ifthetotalaluminium content isat least 0,018%;incasesofdispute,thedissolved aluminium content isto bedetermined.BS EN 100286:2017EN 10028-6:2017 (E) 8 Table 2 Permissible deviations

49、 of the chemical composition in the results of the product analysis from the specified values applicable to the cast analysis Element Specified value in the cast analysis according to Table 1 % by mass Permissible deviation aof the product analysis % by mass C 0,20 + 0,02 Si 0,80 + 0,05 Mn 1,70 + 0,10 P 0,025 + 0,005 S 0,010 + 0,003 Altotal 0,018 0,005 N 0,015 + 0,002 B 0,005 + 0,000 5 Cr 1,50 + 0,10 Mo 0,70 + 0,04 Cu 0,30 + 0,05 Ni 2,50 + 0,10 Nb 0,06 + 0,01 Ti 0,05 + 0