EN 10143-2006 en Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape《连续热浸涂覆的薄钢板和钢带 尺寸和形状公差》.pdf

1、BRITISH STANDARDBS EN10143:2006Continuously hot-dip coated steel sheet and strip Tolerances on dimensions and shapeThe European Standard EN 10143:2006 has the status of a British StandardICS 77.140.50g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40

2、g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 10143:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2006 BSI 2006ISBN 0 580 48907 8National forewordThis British Standard

3、is the official English language version of EN 10143:2006. It supersedes BS EN 10143:1993 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee ISE/10, Flat rolled steels products, which has the responsibility to: A list of organizations represented on this

4、committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the

5、 “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from leg

6、al obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.Summar

7、y of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 14, an inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsEUR

8、OPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 10143June 2006ICS 77.140.50 Supersedes EN 10143:1993 English VersionContinuously hot-dip coated steel sheet and strip - Toleranceson dimensions and shapeTles et bandes en acier revtues en continu parimmersion chaud - Tolrances sur les dimensions et surl

9、a formeKontinuierlich schmelztauchveredeltes Blech und Band ausStahl - Grenzabmae und FormtoleranzenThis European Standard was approved by CEN on 24 May 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the

10、status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A

11、 version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Est

12、onia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISC

13、HES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10143:2006: EEN 10143:2006 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and

14、 definitions .4 4 Designation 4 5 Condition of delivery .5 6 Tolerances on thickness.5 7 Tolerances on width 9 7.1 General9 7.2 Sheet and wide strip of width 600 mm .9 7.3 Slit wide strip of width less than 600 mm .10 8 Tolerances on length.11 9 Tolerances on flatness11 9.1 Steel grades with specifi

15、ed minimum Reor Rp0,2 1 500 1 200b1 200 1 500 0,20 1 500 1 200b1 200 1 500 0,20 1 500 1 200b1 200 1 500 0,35 t 0,40 0,05 0,06 0,07 0,040 0,045 0,050 0,40 1500 1200b1200 1500 0,35 1 800 80+30+7.3 Slit wide strip of width less than 600 mm The tolerances on width of slit wide strip of width 8 000 by ag

16、reement 9 Tolerances on flatness 9.1 Steel grades with specified minimum Reor Rp0,2 360 MPa The tolerance on flatness is the maximum permitted distance between the sheet and the horizontal surface on which it is placed. Flatness tolerances shall be as given in Tables 8 and 9. The measurement of wavi

17、ness is only made on sheet edges. The flatness tolerances apply only to sheet. Flatness tolerances closer than special tolerances _ may be agreed at the time of enquiry and order. Table 8 Flatness tolerances for steel grades with specified minimum yield strength Reor specified minimum proof strength

18、 Rp0,2 260 MPa Dimensions in millimetres Tolerance class Nominal width w Maximum wave height for nominal thickness t t 0,7 0,7 t 1,6 1,6 t 3,0 3,0 t 6,5 w 1 200 10 8 15 1 200 w 1 500 12 10 18 Normal w 1 500 17 15 23 w 1 200 5 4 3 8 1 200 w 1 500 6 5 4 9 Special (FS) w 1 500 8 7 6 12 EN 10143:2006 (E

19、) 12 Table 9 Flatness tolerances for steel grades with specified minimum proof strength 260 MPa Rp0,2 360 MPa and for grades DX51D and S550GD Dimensions in millimetres Tolerance class Nominal width w Maximum wave height for nominal thickness t t 0,7 0,7 t 1,6 1,6 t 3,0 3,0 t 6,5 w 1 200 13 10 18 Nor

20、mal 1 200 w 1 500 15 13 25 w 1 500 20 19 28 w 1 200 8 6 5 9 Special (FS) 1 200 w 1 500 9 8 6 12 w 1 500 12 10 9 14 9.2 Steel grades with specified minimum Rp0,2 360 MPa For these steel grades, the values for flatness tolerances shall be specified at the time of enquiry and order. 10 Tolerances on ou

21、t-of-squareness The out-of-squareness u is the orthogonal projection of transverse edge over a longitudinal edge (see Figure 1). The out-of-squareness shall not exceed 1 % of the actual width of the sheet. Figure 1 Out-of-squareness u and edge camber q 11 Tolerances on edge camber The edge camber q

22、is the maximum distance between a longitudinal edge and a straight edge supported on the latter (see Figure 1). Edge camber shall be measured on the concave edge. The basis of measurement shall be a distance of 2 m taken at any point on the edge. In the case of sheets and cut lengths with a length l

23、ess than 2 m, the basis measurement shall be equal to their length. EN 10143:2006 (E) 13 The edge camber shall not exceed 5 mm over a length of 2 m. For lengths less than 2 m, the edge camber shall not exceed 0,25 % of the actual length. For slit wide strip of width 600 mm a special edge camber tole

24、rance (CS) of 2 mm maximum on a length of 2 m may be specified. This special edge camber tolerance is not applicable for steels with specified minimum proof strength Rp0,2 280 MPa. 12 Superimposition of dimensions By agreement at the time of enquiry and order the tolerance on out-of-squareness and e

25、dge camber may be replaced by a requirement that a perfect rectangle formed by the ordered width and length dimensions can be superimposed onto the sheets delivered. EN 10143:2006 (E) 14 Bibliography 1 EN 10051, Continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy steels To

26、lerances on dimensions and shape 2 EN 10131, Cold rolled uncoated low carbon and high yield strength steel flat products for cold forming Tolerances on dimensions and shape 3 EN 10292, Continuously hot-dip coated strip and sheet of steels with higher yield strength for cold forming Technical deliver

27、y conditions 4 EN 10326, Continuously hot-dip coated strip and sheet of structural steels Technical delivery conditions 5 EN 10327, Continuously hot-dip coated strip and sheet of low carbon steels for cold forming Technical delivery conditions 6 prEN 10336, Continuously hot-dip coated and electrolyt

28、ically coated strip and sheet of multiphase steels for cold forming Technical delivery conditions blankBS EN 10143:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on st

29、andards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality

30、of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20

31、8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20

32、8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise re

33、quested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and servic

34、es. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Mem

35、bership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopy

36、right subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any for

37、m or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.