EN 1015-10-1999 en Methods of Test for Mortar for Masonry - Part 10 Determination of Dry Bulk Density of Hardened Mortar (Incorporates Amendment A1 2006)《圬工灰浆试验方法 第10部分 硬化灰浆干块密度测定 .pdf

1、BRITISH STANDARD BS EN 1015-10:1999 Incorporating amendment no. 1 Methods of test for mortar for masonry Part 10: Determination of dry bulk density of hardened mortar The European Standard EN 1015-10:1999, incorporating amendment A1:2006, has the status of a British Standard ICS 91.100.10 BS EN 1015

2、-10:1999 This British Standard, having been prepared under the direction of the Sector Committee for Building and Civil Engineering, was published under the authority of the Standards Committee and comes into effect on 15 November 1999 BSI 2007 ISBN 0 580 35468 7 National foreword This British Stand

3、ard was published by BSI. It is the UK implementation of EN 1015-10:1999, incorporating amendment A1:2006. It is included in a package of standards relating to masonry mortar and rendering and plastering mortar which supersedes the following British Standards which are withdrawn. BS 4551-1:1998, Met

4、hods of testing mortars, screeds and plasters Part 1: Physical testing; BS 4721:1981, Specification for ready-mixed building mortars; BS 5838-2:1980, Specification for dry packaged cementitious mixes Part 2: Prepacked mortar mixes. The start and finish of text introduced or altered by amendment is i

5、ndicated in the text by tags !“. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by !“. The UK participation in its preparation was entrusted by Technical Committee B/519, Masonry and associated testing, to Subcomm

6、ittee B/519/2, Mortar. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard can

7、not confer immunity from legal obligations. Amendments issued since publication Amd. No. Date Comments 16879 31 January 2007 See national forewordCEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B

8、-1050 Brussels 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1015-10:1999 E EUROPEAN STANDARD EN 1015-10 NORME EUROPE ENNE EUROPA ISCHE NORM August 1999 ICS 91.100.10 English version Methods of test for mortar for masonry Pa

9、rt 10: Determination of dry bulk density of hardened mortar Me thodes dessai des mortiers pour mac onnerie Partie 10: De termination de la masse volumique apparente se che du mortier durci Pru fverfahren fu rM o rtel fu r Mauerwerk Teil 10: Bestimmung der Trockenrohdichte von Festmo rtel This Europe

10、an Standard was approved by CEN on 8 July 1999. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concern

11、ing such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own la

12、nguage and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden

13、, Switzerland and United Kingdom. A1 + December 2006 Page 2 EN 1015-10:1999 Foreword This European Standard has been prepared by Technical Committee CEN/TC 125, Masonry, the Secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by public

14、ation of an identical text or by endorsement, at the latest by February 2000, and conflicting national standards shall be withdrawn at the latest by December 2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implemen

15、t this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Principle 3 4 Sy

16、mbols 3 5 Apparatus 3 6 Sampling, preparation and storage of test samples 3 7 Procedure 4 8 Calculation and expression of results 4 9 Test report 4Foreword to amendment A1 BSI 2007 This document (EN 1015-10:1999/A1:2006) has been prepared by Technical Committee CEN/TC 125 “Masonry”, the secretariat

17、of which is held by BSI. This Amendment to the European Standard EN 1015-10:1999 shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2007, and conflicting national standards shall be withdrawn at the latest by June 200

18、7. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

19、 Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Page 3 EN 1015-10:1999 1 Scope This European Standard specifies a method for determining the dry bulk density of hardened mortars. It is applicable to lig

20、htweight and general purpose and thin layer mortars using specimens of regular shape. 2 Normative references Part 1: Rendering and plastering mortar with inorganic binding agents. Part 2: Masonry mortar. EN 1015-2, Methods of test for mortar for masonry Part 2: Bulk sampling of mortars and preparati

21、on of test mortars. EN 1015-3, Methods of test for mortar for masonry Part 3: Determination of consistence of fresh mortar (by flow table). EN 1015-11, Methods of test for mortar for masonry Part 11: Determination of flexural and compressive strength of hardened mortar. 3 Principle The dry bulk dens

22、ity of a given specimen of hardened mortar is determined as the quotient of its mass in oven dried condition, and the volume which it 4 Symbols m s,dry is the oven dry mass of specimen of hardened mortar, in kilograms (kg); V s is the volume of specimen of hardened mortar, in cubic metres (m 3 ). 5

23、Apparatus 5.1 A weighing instrument, accurate to 0,1 % of the total mass of the specimen. 5.2 A ventilated oven, capable of maintaining a temperature of 708C 58Co r6 08 C 58 C. 5.3 Moulds, as described in EN 1015-11. 6 Sampling, preparation and storage of test samples The fresh mortar for this test

24、shall have a volume of not less than 50 times the maximum aggregate particle size, and in no case less than 50 ml or 1,5 times the quantity needed to perform the test, whichever is the greater. It shall be obtained either by reduction of the bulk test sample (see EN 1015-2) using a sample divider or

25、 by quartering or by preparation from dry constituents and water in the laboratory. The flow value of the mortar in the bulk test sample shall be determined in accordance with EN 1015-3 and reported. Laboratory mixed samples shall, before testing, be brought to a defined flow value as specified in E

26、N 1015-2. Ready to use mortars (factory-made wet mortars which are retarded), and pre-batched air-lime/sand wet mortars when not gauged with hydraulic binders, shall be tested within their specified workable life. The length of mixing period shall be measured from the moment all constituents are int

27、roduced into the mixer. Before testing, the batch shall be gently stirred by hand using a trowel or palette knife in 5 s to 10 s to counteract any false setting etc., but without any additional mixing of the batch. Any deviation from the mixing procedure shall be noted. A test sample shall comprise

28、three specimens prepared in moulds, their shape, preparation and storage being in accordance with EN 1015-11.EN 998-1, Specification for mortar for masonry ! “ EN 998-2, Specification for mortar for masonry ! “ occupies. ! “ Text deleted ! “ ! “ BSI 2007!The following referenced documents are indisp

29、ensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. “ Page 4 EN 1015-10:1999 1) This information is contained on the certificate of sampling (see

30、EN 1015-2). 7 Procedure Dry the specimen in the oven at a temperature of until the constant mass is reached. For samples with organic constituents, e.g. expanded polystyrene aggregate, use a drying temperature of 608C 58C. The specimen is considered to have reached constant mass if two consecutive w

31、eighings 2 h apart during the drying, do not differ by more than 0,2 % of the mass of the dry specimen. Record the mass of the specimen, m s,dry in kg to the nearest 0,1 %. 8 Calculation and expression of results Calculate the dry bulk density of each mortar specimen as the ratio of the recorded mas

32、s, m s,dry ,t o the volume V s . Calculate the mean value from the individual values of each mortar specimen, all values rounded to the nearest 10 kg/m 3 . 9 Test report The test report shall include the following information: a) the number, title and date of issue of this European Standard; b) the

33、place, date and time of taking the bulk test sample 1) ; NOTE This is the sample taken from the bulk supply that is to be used for all of the tests in EN 1015. c) the method used for taking the bulk test sample (if known) and the name of the organization that took it; d) the type, origin and designa

34、tion of the mortar by e) the date of testing; f) the date and time of preparing test samples for test (i.e. date and time of any mixing, casting, moulding, or demoulding procedure, if appropriate; g) flow value of test mortar determined in accordance with EN 1015-3; h) details of test specimens incl

35、uding number, dimensions, mass etc., if appropriate; i) test results (individual and mean values of dry bulk density rounded to the nearest 10 kg/m 3 ); j) remarks, if any. Text deleted ! “ !105 C 5 C “ !V sis taken as the volume of the mould, which is 256 10 -6m 3 . “ BSI 2007 reference to the rele

36、vant part of EN 998; ! “blankBS EN 1015-10:1999 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporat

37、ed by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone fi

38、nding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service ca

39、lled PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Stan

40、dards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range

41、 of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7

42、111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +

43、44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI a

44、lso holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, r

45、ecording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.