1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 10223-4:2012Steel wire and wire productsfor fencing and nettingPart 4: Steel wire welded mesh fencingBS EN 10223-4:2012 BRITISH STANDARDNational forewordThis British Standa
2、rd is the UK implementation of EN 10223-4:2012. It supersedes BS EN 10223-4:1998, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e I S E / 1 0 6 , W i r e R o d a n d W i r e .A list of organizations represented on this committee can be
3、obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012.ISBN 978 0 580 64501 3 ICS 77.140.65 Compli
4、ance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 10223-4:2012EUROPEAN STANDARD NOR
5、ME EUROPENNE EUROPISCHE NORM EN 10223-4 November 2012 ICS 77.140.65 Supersedes EN 10223-4:1998English Version Steel wire and wire products for fencing and netting - Part 4: Steel wire welded mesh fencing Fils et produits trfils en acier pour cltures et grillages - Partie 4: Grillage en acier soud St
6、ahldraht und Drahterzeugnisse fr Zune und Drahtgeflechte - Teil 4: Geschweite Gitter aus Stahldraht fr Zune This European Standard was approved by CEN on 13 October 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
7、 Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (E
8、nglish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgiu
9、m, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerl
10、and, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref.
11、 No. EN 10223-4:2012: EBS EN 10223-4:2012EN 10223-4:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Information to be supplied by the purchaser .65 Manufacture 65.1 Base metal 65.2 Fabrication 65.2.1 Rolls 65.2.2 Panels .75.3 Welding .76 Requirements .
12、76.1 Tensile strength .76.2 Tolerance on wire diameters 76.3 Coatings 76.3.1 Zinc and zinc alloy coatings .76.3.2 Organic material coatings .86.4 Tolerance on mesh dimensions .86.5 Weld shear strength 87 Sampling and testing 88 Inspection documentation 99 Test methods 99.1 Tensile test .99.2 Wire di
13、mension 99.3 Weld shear strength 99.4 Coating tests 99.4.1 Zinc or zinc alloy coating of wire before welding .99.4.2 Welded mesh which is zinc or zinc alloy coated after welding 99.4.3 Hot dip zinc or zinc alloy coating by a batch process (panels) 99.4.4 Coated with organic material after fabricatio
14、n .910 Packaging .9Annex A (normative) Weld shear strength test method (welded mesh) . 10BS EN 10223-4:2012EN 10223-4:2012 (E) 3 Foreword This document (EN 10223-4:2012) has been prepared by Technical Committee ECISS/TC 106 “Wire rod and wires”, the secretariat of which is held by AFNOR. This Europe
15、an Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2013, and conflicting national standards shall be withdrawn at the latest by May 2013. Attention is drawn to the possibility that some of the elements of t
16、his document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10223-4:1998. EN 10223 “Steel wire and wire products for fencing and netting“ consists of the following parts: Part 1: Zinc an
17、d zinc-alloy coated steel barbed wire Part 2: Hexagonal steel wire netting for agricultural, insulation and fencing purposes Part 3: Hexagonal steel wire mesh products for engineering purposes Part 4: Steel wire welded mesh fencing Part 5: Steel wire woven hinged joint and knotted mesh fencing Part
18、6: Steel wire chain link fencing Part 7: Steel wire welded panels for fencing Part 8: Welded mesh gabion products According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgar
19、ia, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turk
20、ey and the United Kingdom. BS EN 10223-4:2012EN 10223-4:2012 (E) 4 1 Scope This European Standard specifies requirements for steel wire welded mesh fencing of which there are many types for a variety of applications. It specifies the general characteristics of welded mesh fencing supplied as rolls o
21、r panels and coatings, properties and tolerances. This European Standard covers only orthogonal welded mesh i.e. wire welded at right angles to one another. For welded mesh fencing made from panels the specification covers only panels made from wires not greater than 10 mm. 2 Normative references Th
22、e following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10021,
23、 General technical delivery conditions for steel products EN 10204, Metallic products Types of inspection documents EN 10218-1, Steel wire and wire products General Part 1: Test methods EN 10218-2:2012, Steel wire and wire products General Part 2: Wire dimensions and tolerances EN 10244-1, Steel wir
24、e and wire products Non-ferrous metallic coatings on steel wire Part 1: General principles EN 10244-2:2009, Steel wire and wire products - Non-ferrous metallic coatings on steel wire Part 2: Zinc or zinc alloy coatings EN 10245-1, Steel wire and wire products Organic coatings on steel wire Part 1: G
25、eneral rules EN 10245-2, Steel wire and wire products Organic coatings on steel wire Part 2: PVC finished wire EN 10245-3, Steel wire and wire products Organic coatings on steel wire Part 3: PE coated wire EN ISO 1461, Hot dip galvanized coatings on fabricated iron or steel articles Specifications a
26、nd test methods (ISO 1461) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 welded mesh fencing fencing made by electrical resistance welding either: a) zinc-coated or zinc alloy coated wires; or b) bright wires which are subsequently coated a
27、fter welding either with zinc or zinc alloy Note 1 to entry: In both cases, the wire may or may not be crimped. The welded mesh may or may not be subsequently coated with an organic material. BS EN 10223-4:2012EN 10223-4:2012 (E) 5 3.2 spacing distance measured between leading edge and leading edge
28、of wires (see Figure 1) 3.3 mesh size of welded mesh spacing of line wires followed by the spacing of cross wire e.g. for 50 mm line wire spacing and 25 mm cross wire spacing the mesh size is 50 mm x 25 mm 3.4 line wires wires running in the longitudinal direction parallel with the length of the rol
29、l or panel (see Figure 1) 3.5 cross wires wires running in the transverse direction (see Figure 1) Note 1 to entry: On erection of the fence, the cross wires become vertical. 3.6 panel welded mesh produced in flat form to specified dimensions or cut from rolls of welded mesh Note 1 to entry: Panels
30、are produced either with overhanging edges or with flush cut edges Key 1 cross wires 2 line wire spacing 3 cross wire spacing 4 line wires Figure 1 Example of mesh BS EN 10223-4:2012EN 10223-4:2012 (E) 6 4 Information to be supplied by the purchaser The following information shall be supplied by the
31、 purchaser at the time of enquiry and order: a) number of this European Standard; b) quantity and packaging; c) if for agricultural use or not; d) roll or panel; e) mesh size(s); f) diameters of line and cross wires; g) length and width of rolls or size of panels; h) the class of zinc or zinc/alloy
32、coating and whether applied before or after manufacture and if required, the adherence and assessment of adherence (wrap specification); i) whether an organic material coating is required and, if so, the type and colour; j) tensile strength of line wires and cross wires if different from each other;
33、 k) whether or not crimping is required in line or cross wires; l) if applicable, the number of apertures required; m) in the case of panels, whether to be produced with overhangs or cut flush; n) test report requirements; o) agreed quality characteristics for testing (see Clause 7). 5 Manufacture 5
34、.1 Base metal The base metal of the welded mesh fencing shall be low carbon steel. 5.2 Fabrication 5.2.1 Rolls The welded mesh fencing in roll shall be fabricated by electrical resistance welding either from: a) bright wires which subsequently after welding are either zinc or zinc alloy coated to EN
35、 10244-1 and EN 10244-2:2009, class A; or b) zinc or zinc alloy wire coated to EN 10244-1 and EN 10244-2:2009, class A, unless otherwise agreed at the time of enquiry and order. Where requested by the purchaser the welded mesh fencing shall be subsequently coated with an organic material to EN 10245
36、-1 and EN 10245-2 or EN 10245-3. The type and colour and any other criteria shall be given on the order. BS EN 10223-4:2012EN 10223-4:2012 (E) 7 5.2.2 Panels Panels shall be produced by either: a) cutting from zinc or zinc alloy coated rolls; or b) by electrical resistance welded bright wires and su
37、bsequently zinc or zinc alloy coated to EN ISO 1461. No bare patches shall be permitted. When requested by the purchaser the welded mesh fencing shall be subsequently coated with an organic material to EN 10245-1 and EN 10245-2 or EN 10245-3. The type and colour and any other criteria shall be given
38、 on the order. 5.3 Welding The mesh shall be produced by electrical resistance welding at every line wire/cross wire intersection. The line and/or cross wires may be crimped. Depending on the application, the mesh spacing throughout the fencing may be the same, as in 50 mm x 50 mm security mesh or v
39、arying as in the welded mesh fencing for agricultural or general use i.e. decreasing mesh size from the top downwards. The diameter of line wires may be different from the diameter of cross wires. 6 Requirements 6.1 Tensile strength The tensile strength of the line and cross wires shall be in the ra
40、nge 350 N/mm2 to 950 N/mm2. For any delivered lot, the spread of tensile strength shall be within 200 N/m2. NOTE The tensile strength of the line wires may not be the same as the tensile strength of the cross wires. 6.2 Tolerance on wire diameters The tolerance in diameter of the wires shall comply
41、with the following grades from EN 10218-2. a) zinc or zinc alloy coated wire to EN 10244-2:2009, class A, tolerance shall be to EN 10218-2:2012, T1 (Table 1). b) other zinc or zinc alloy coated wire, tolerance shall be to EN 10218-2:2012, T2 (Table 1). c) bright wire, tolerance shall be to EN 10218-
42、2:2012, T3 (Table 1). d) wire coated with an organic material, tolerance shall be to EN 10218-2:2012 (Table 2). 6.3 Coatings 6.3.1 Zinc and zinc alloy coatings 6.3.1.1 Rolls When coating applies to EN 10244-2:2009, class A, samples taken from the fence shall have the minimum coating mass requirement
43、 reduced by 5 % and where specified the number of dips shall be reduced by one half minute dip. BS EN 10223-4:2012EN 10223-4:2012 (E) 8 Additionally, the adherence and wrapping requirements shall be as agreed at the time of enquiry and order. 6.3.1.2 Panels Where panels have been cut from zinc or zi
44、nc alloy coated rolls, the coated wire shall comply with the requirements of 6.3.1.1. Where panels have been produced by zinc or zinc alloy coating after fabrication the coated panels shall comply with the requirements of EN ISO 1461. Where mesh in panels coated after fabrication contains two diamet
45、ers of wire, the coating mass shall not be less than the average of the specified minimum values of the two diameters. 6.3.2 Organic material coatings When present, organic material coatings shall comply with the appropriate part of EN 10245-1 and EN 10245-2 or EN 10245-3. 6.4 Tolerance on mesh dime
46、nsions The nominal mesh spacing measured leading edge to leading edge shall be subject to the tolerances in Table 1 after coating. Table 1 Tolerances on mesh spacing Dimensions in millimeters Mesh spacing x Tolerance x 25 2,0 25 75 5,0 The mesh shall have the number of apertures given on the order.
47、The variation in the mesh spacing shall provide a maximum cumulative variation of 5 mm per meter. 6.5 Weld shear strength When tested in accordance with Annex A the average of all the four loads shall not be less than 75 % of the wire breaking load of the smallest diameter wire. NOTE Breaking load i
48、s the maximum force during the tensile test before breaking. If the average fails to meet this requirement, all the welds across the specimen shall be tested. The mesh shall be deemed acceptable if the average of all the weld shear test values across the specimen is greater than 75 % of the wire bre
49、aking load of the smallest diameter wire. 7 Sampling and testing The manufacturer shall be responsible for the control of product quality by the application of statistical methods of sampling and analysis of results or, alternatively, by sampling and testing for the agreed quality characteristics at a rate of one roll/reel in one sample every week or one per production change. BS EN 10223-4:2012EN 10223-4:2012 (E) 9 8 Inspection documentation Unless ot
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1