EN 10223-5-2012 en Steel wire and wire products for fencing and netting - Part 5 Steel wire woven hinged joint and knotted mesh fencing《钢丝和钢丝产品击剑和网 第5部分 钢丝编织铰链关节和结网击剑》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 10223-5:2012Steel wire and wire products for fencing and nettingPart 5: Steel wire woven hinged joint and knotted mesh fencingBS EN 10223-5:2012 BRITISH STANDARDNational fo

2、rewordThis British Standard is the UK implementation of EN 10223-5:2012. It supersedes BS EN 10223-5:1998, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e I S E / 1 0 6 , W i r e R o d a n d W i r e .A list of organizations represented

3、on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012.Published by BSI Standards Limited 2012.ISBN 978 0 580 6450

4、2 0 ICS 77.140.65 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 10223-5:2

5、012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10223-5 November 2012 ICS 77.140.65 Supersedes EN 10223-5:1998English Version Steel wire and wire products for fencing and netting - Part 5: Steel wire woven hinged joint and knotted mesh fencing Fils et produits trfils en acier pour cltures et

6、 grillages - Partie 5: Grillage nou et grillage raccords pivotants en acier Stahldraht und Drahterzeugnisse fr Zune und Drahtgeflechte - Teil 5: Gelenk- und Knotengitter aus Stahldraht fr Zune This European Standard was approved by CEN on 13 October 2012. CEN members are bound to comply with the CEN

7、/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Cen

8、tre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as th

9、e official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Nether

10、lands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploi

11、tation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10223-5:2012: EBS EN 10223-5:2012EN 10223-5:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Information to be supplied by the purchaser .65 Designation of hing

12、ed joint and knotted mesh fencing.66 Manufacture 66.1 Base metal 66.2 Fabrication 77 Requirements .77.1 Tensile strength .77.1.1 Woven hinged joint fencing 77.1.2 Knotted mesh fencing .77.2 Wire diameters .77.2.1 Woven hinged joint fencing 77.2.2 Knotted mesh fencing .77.3 Tolerances 77.4 Coating 78

13、 Sampling and testing . 109 Inspection documentation . 1010 Test methods . 1010.1 Tensile tests 1010.2 Coating tests . 1011 Packaging 10Annex A (informative) Typical designations for hinged joint and knotted joint fencing 11BS EN 10223-5:2012EN 10223-5:2012 (E) 3 Foreword This document (EN 10223-5:2

14、012) has been prepared by Technical Committee ECISS/TC 106 “Wire rod and wires”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2013, and conflictin

15、g national standards shall be withdrawn at the latest by May 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document super

16、sedes EN 10223-5:1998. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. EN 10223 “Steel wire and wire products for fencing and netting“ consists of the following parts: Part 1: Zinc and zinc-alloy coated steel barbed wir

17、e Part 2: Hexagonal steel wire netting for agricultural, insulation and fencing purposes Part 3: Hexagonal steel wire mesh products for engineering purposes Part 4: Steel wire welded mesh fencing Part 5: Steel wire woven hinged joint and knotted mesh fencing Part 6: Steel wire chain link fencing Par

18、t 7: Steel wire welded panels for fencing Part 8: Welded mesh gabion products According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic,

19、 Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 102

20、23-5:2012EN 10223-5:2012 (E) 4 1 Scope This European Standard specifies preferred dimensions, properties and coatings of zinc and zinc alloy coated steel wire woven hinged joint and knotted mesh fencing. 2 Normative references The following documents, in whole or in part, are normatively referenced

21、in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10021, General technical delivery conditions for steel products EN 10204, Met

22、allic products Types of inspection documents EN 10218-1, Steel wire and wire products General Part 1: Test methods EN 10218-2:2012, Steel wire and wire products General Part 2: Wire dimensions and tolerances EN 10244-1:2009, Steel wire and wire products Non-ferrous metallic coatings on steel wire Pa

23、rt 1: General principles EN 10244-2:2009, Steel wire and wire products Non-ferrous metallic coatings on steel wire Part 2: Zinc and zinc alloy coatings 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 knotted mesh fencing fencing with rectangu

24、lar meshes made of line and stay wires zinc or zinc alloy coated to EN 10244-1:2009 and EN 10244-2:2009, class A The line and stay wires are connected by a hinged joint spiral knot in the case of hinge joint stock fence (see Figure 1) and by a knot in the case of knotted stock fence (see Figure 2) (

25、except for the selvedge wire which is spiral knotted): The top and bottom wires of the fence may consist of a larger diameter selvedge wire. The rectangular mesh openings may decrease in size from the top downwards. The line and selvedge wire are regularly and evenly crimped between the stay wires (

26、to aid erection of the fence) 3.2 woven joint fencing classification relating to: a) strength of wire: 1. strength 1 applies to fencing manufactured from low tensile wire; 2. strength 2 applies to fencing manufactured from high tensile wire; BS EN 10223-5:2012EN 10223-5:2012 (E) 5 b) nominal diamete

27、r of wires incorporated in the fence using: 1. L for light (small diameter wire); 2. M for medium (medium diameter wire); 3. H for heavy (large diameter wire) Key 1 selvedge wire 4 length 2 stay wire 5 height 3 line wire Figure 1 Example of woven hinged joint design a) b) c) Figure 2 Examples of kno

28、tted joint design BS EN 10223-5:2012EN 10223-5:2012 (E) 6 4 Information to be supplied by the purchaser The following information shall be supplied by the purchaser at the time of enquiry and order: a) number of this European Standard; b) quantity; c) hinged joint or knotted joint; d) classification

29、 (i.e. L, M or H and 1 or 2 according to Table 1); e) designation (see Clause 5, Table A.1 and Table A.2); f) length of rolls; g) height of roll; h) number of line wires and stay wire spacing; i) for 2M and 2H (according to Table 1) the size of selvedge wire required; j) coating type, zinc or zinc a

30、lloy; k) if uniformity of coating is to be measured; l) inspection documentation requirements; m) agreed quality characteristics for testing (see Clause 7). 5 Designation of hinged joint and knotted mesh fencing Figure 3 EXAMPLE 80/8/15 Typical designations of hinged joint and knotted mesh fencing a

31、re given in Table A.1 and Table A.2. 6 Manufacture 6.1 Base metal Wires shall be manufactured from steel rod capable of achieving the tensile properties given in Tables 1 and 2. BS EN 10223-5:2012EN 10223-5:2012 (E) 7 6.2 Fabrication The hinge joint or knotted fence shall be made from zinc or zinc-a

32、lloy coated wires which conform to EN 10244-1 and EN 10244-2. The line and selvedge wires shall be regularly and evenly crimped between the stay wires (to aid erection of the fence). In the case of hinge joint fencing the wires shall be twisted at least one and a half times to ensure that the hinge

33、joints are tightly fixed. In the case of knotted joint fencing the knots shall be manufactured so that they are tightly fixed. 7 Requirements 7.1 Tensile strength 7.1.1 Woven hinged joint fencing The tensile strength of wires shall not be less than that given in Table 1 for the classification and te

34、nsile strength required. The tensile strength range for any one batch within a type of wire shall be not more than 200 N/mm2. 7.1.2 Knotted mesh fencing The tensile strength of the wires shall be not less than that given in Table 2. The tensile strength range in any one batch within a wire type shal

35、l be not more than 200 N/mm2. 7.2 Wire diameters 7.2.1 Woven hinged joint fencing The nominal diameters of wires shall be as given in Table 1 and shall be subject to tolerance EN 10218-2:2012 (T1 Table 1). 7.2.2 Knotted mesh fencing The nominal diameters of wires shall be as given in Table 2 and sha

36、ll be subject to tolerance EN 10218-2:2012 (T1 - Table 1). 7.3 Tolerances The tolerance on roll width is 25 mm. The maximum variation in any individual vertical or horizontal spacing shall be no more than 5 mm from the nominal stated by the manufacturer. NOTE Rolls are usually supplied with either 1

37、50 or 300 mm spacing between verticals, but other spacing may be arranged by agreement. 7.4 Coating The zinc or zinc alloy coating of wire shall be tested in accordance with EN 10244-2:2009 complying with class A for Zn coatings and class B for Zn95/Al5 alloys (for similar service life), adherence a

38、nd where specified, the uniformity of the coating BS EN 10223-5:2012EN 10223-5:2012 (E) 8 Where samples are taken from a fabricated fence the minimum coating mass requirement shall be reduced by 5 % and where specified the number of dips shall be reduced by one half minute dip. The assessment of adh

39、erence (wrap quality) on 1 diameter for all wires prior to fabrication of the fence shall comply with EN 10244-2:2009 (Figure 1) classes 1 or 2. The assessment of adherence (wrap quality) on 1 diameter of the wire in the fabricated fence shall comply with EN 10244-2:2009 (Figure 1) classes 1, 2 or 3

40、. BS EN 10223-5:2012BS EN 10223-5:2012EN 10223-5:2012 (E) 9 Table 1 Preferred nominal diameters and minimum tensile strengths for woven hinged joint fencing Wire type Low tensile steel woven wire hinged joint High tensile woven wire hinged joint Light 1L Medium1M Heavy 1H Light 2L Mdum2M Heavy 2H No

41、minal diameter Minimum tensile strength Nominal diameter Minimum tensile strength Nominal diameter Minimum tensile strength Nominal diameter Minimum tensile strength Nominal diameter Minimum tensile strength Nominal diameter Minimum tensile strength mm N/mm2mm N/m2mm N/m2mm N/m2mm N/m2mm N/m2Top and

42、 bottom line (horizontal) selvedge wires 2,50 600 3,00 600 3,70 550 1,60 or 2,00 1 050 2,00 or 2,50 1 050 2,50 or 3,00 a1 050 Intermediate line (horizontal) wires 1,90 600 2,50 600 3,00 600 1,60 1 050 2,00 1 050 2,50 1 050 Stay (vertical) wires 1,90 400 2,50 350 3,00 350 1,60 600 2,00 600 2,50 600 T

43、ensile strength range for any one batch within a type of wire shall be not more than 200 N/mm2. aWhere the duty of the fence requires them, larger diameter selvedge wires may be agreed. BS EN 10223-5:2012EN 10223-5:2012 (E) 10 Table 2 Preferred nominal wire diameters and minimum tensile strengths of

44、 wire for woven knotted mesh fencing Wire type Nominal wire diameter mm Minimum tensile strength N/mm2Top and bottom line/selvedge (horizontal) wires 3,70 550Intermediate line (horizontal) wires 3,00 600 Stay (vertical) wires 3,00 600 Knot wire 3,00 350 Tensile strength range in any one batch within

45、 a wire type shall be not more than 200 N/mm2. 8 Sampling and testing The manufacturer shall be responsible for the control of product quality by the application of statistical methods of sampling and analysis of results or, alternatively, by sampling and testing for the agreed quality characteristi

46、cs at a rate of one roll/reel in 50. 9 Inspection documentation Unless otherwise agreed at the time of enquiry and order, non specific testing and inspection documentation shall be provided according to the requirements of EN 10021 and EN 10204. 10 Test methods 10.1 Tensile tests Tensile tests shall

47、 be in accordance with EN 10218-1. 10.2 Coating tests The zinc or zinc alloy coated wire before fabrication into the fence shall be tested for the weight, adherence of coating and, where required, the uniformity of coating in accordance with EN 10244-1 and EN 10244-2. 11 Packaging Woven hinged or kn

48、otted joint fencing shall usually be supplied in 50 m or 100 m rolls with a tolerance of 10 +m. Other lengths may be supplied by agreement. BS EN 10223-5:2012BS EN 10223-5:2012EN 10223-5:2012 (E) 11 Annex A(informative) Typical designations for hinged joint and knotted joint fencing Table A.1 Typica

49、l woven hinged joint fencing designations No. of line Approximate woven roll width in centimeters wires 53 60 65 80 90 95 100 115 120 125 130 140 145 150 155 160 180 190 200 220 4 60/4/15 5 53/5/15 60/5/15 6 60/6/15 65/6/15 80/6/15 90/6/30 7 80/7/15 100/7/15 8 80/815 90/815 100/8/15 115/8/30 145/8/15 9 100/9/15 120/9/15 125/9/15 10 95/10/15 120/10/15 140/10/15 11 130/11/15 140/11/15 150/11/15 160/11