EN 10244-3-2001 en Steel Wire and Wire Products - Non-Ferrous Metallic Coatings on Steel Wire - Part 3 Aluminium Coatings《钢丝及其制品 钢丝上的非有色金属涂层 第3部分 铝涂层》.pdf

1、STD=BSI BS EN L0244-3-ENGL 2001 D Lb24bb9 0709257 04T I BRITISH STANDARD Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 3: Aluminium coatings The European Standard EN 10244-3:2001 has the status of a British Standard ICs 25.220.40; 77.140.65 BS EN 10244-3 :200 1 NO

2、 COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW STDmBSI BS EN L0244-3-ENGL ZOO present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments

3、and promulgate them in the UK. - A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue u

4、nder the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct

5、 application. Compliance with a British Standard does not of itself confer immunity from legal obligations. This British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 Ma

6、y 2001 Summary Of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication 8 BSI 05-20

7、01 I I ISBN O 580 37142 5 - STD-BSI BS EN L0244-3-ENGL 2001 Lb24bb9 0907257 9L2 EUROPEAN STANDARD EN 102443 NORME EUROPENNE EUROPISCHE NORM March 2001 ICs 25.220.40 English version Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 3: Aluminium coatings Fils et produit

8、s trfils en acier - Revtements mtalliques non ferreux sur fils dacier - Partie 3: Revtements daluminium Stahldraht und Drahterzeugnisse - berzge aus Nichteisenmetall auf Stahldraht - Teil 3: berzge aus Aluminium This European Standard was approved by CEN on 21 January 2001. CEN members are bound to

9、comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Managem

10、ent Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the off

11、icial versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMiTEE FOR STANDARDIZATION COMIT

12、E EUROPEEN DE NORMALISATION EUROPISCHES KOMITEE FOR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels O 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10244-3:2001 E STDeBSI BS EN L0244-3-ENGL 20011 I Lb24bb7 090

13、92b0 634 Page 2 EN 10244-312001 Contents Foreword . 3 1 2 3 4 4 .I 4.2 4.3 4.4 4.5 5 5.1 5.1.1 5.1.2 5.2 Scope . 4 Normative references . 4 Terms and definitions . 4 Requirements relating to coating 4 Material . 4 Coating mass . 4 Adherence of the coating . 5 Special finishes . 5 Tests conditions 5

14、Samples . 5 General . 5 Length of samples 5 Determination of mass of coating . 5 Appearance of coating . 5 6 BSI 052001 STD.BS1 BS EN 10244-3-ENGL 2001 = 1624669 0907263 570 Page 3 EN 10244-312001 Foreword This European Standard has been prepared by Technical Committee ECISSTTC 30, Steel wires, the

15、Secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2001, and conflicting national standards shall be withdrawn at the latest by September 2001. This Eur

16、opean Standard for non-ferrous metallic coating on steel wire is made up of the following parts: Part I: General principles Part 2: Zinc and zinc alloy coatings Part 3: Aluminium coatings Patt 4: Tin coatings Part 5: Nickel coatings Part 6: Copper, bronze and brass coatings According to the CENICENE

17、LEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Swi

18、tzerland and the United Kingdom. O BSI 05-2001 STDmBSI BS EN l10244-3-ENGL 2001 L624bb7 07072b2 407 Page 4 EN 10244-312001 1 Scope This patt of this European Standard specifies the requirements for the mass other properties and testing of aluminium coatings on steel wire and steel wire products of c

19、ircular or other cross-section. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, su

20、bsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 10244-1, Steel wire and wire products -

21、Non-ferrous metallic coatings on steel wire - Part I: General principles ASTM A428, Test method for determining the mass of aluminium coating on steel products 3 Terms and definitions For the purposes of this European Standard the following terms and definitions apply. 3.1 wire with aluminium coatin

22、g wire to which an aluminium coating has been applied primarily to protect it against corrosion and/or to improve its electrical conductivity. The coating is generally applied by passing the wires individually through a bath of molten aluminium, by extrusion or by cladding 3.2 mass of coating mass o

23、f aluminium per unit area is expressed in grams per square meter of stripped wire surface. In the case of thick coatings, the quantity of aluminium on the wire may also be expressed by the radial thickness 4 Requirements relating to coating 4.1 Material The ingot of unrefined aluminium used for the

24、coating shall consist of aluminium with less than the following impurities: Copper (Cu) 0,lO ?lo max. in mass % Iron (Fe) 0,50 % max. in mass % 4.2 Coating mass The minimum mass of aluminium per unit surface area shall comply with the requirements of Table 1. The product standard relating to wire pr

25、oducts with an aluminium coating may specify different requirements for minimum mass. O BSI 05-2001 STD.BSI BS EN 10244-3-ENGL 2001 H 1624669 0709263 343 Page 5 EN 10244-312001 4.3 Appearance of coating The aluminium coated wire shall be free of slivers, scale and other imperfections not consistent

26、with good commercial practice. The coating on the wire shall be continuous, reasonably smooth and as evenly distributed as practicable. 4.4 Adherence of the coating The aluminium wire shall be tested in accordance with EN 10244-1. The mandrel for the wrapping test shall have a diameter equal to thre

27、e times the nominal diameter of the wire tested. 4.5 Special finishes If the customer requires a special finish it shall be specified at the time of enquiry and order. Similarly if drawing after coating with aluminium is requested it shall be specified at the time of enquiry and order. 5 Tests condi

28、tions 5.1 Samples 5.1.1 General See the General requirements in EN 10244-1. 5.1.2 Length of samples The length of the samples shall be sufficient to allow the various tests to be carried out. 5.2 Determination of mass of coating The mass of the coating shall be determined using the gravimetric metho

29、d as indicated in EN 10244-1. The stripping solution, sampling, and other procedures, shall be in accordance with ASTM A428. The calculation of the coatings mass is based on the difference in weight in grammes of a test specimen before and after stripping. if Am = difference in weight by stripping i

30、n grammes; m2 = the weight in grammes of the stripped test sample; d = the diameter of the (round) wire in mm; mA = the mass of coating in g/m2; AFn mA =1962xdx- “2 Q BSI 052001 STD-BSI BS EN 102YY-3-ENGL 2001 Lb24bb9 D9092b4 28T m 1 I Page 6 EN 10244-3:2001 Diameter of wire (mm) d Table 1 - Require

31、ments for the mass of aluminium coating Coating mass Class A“ min. I Class CEb thickness 1.2Id 1.5 1,5 I d e 2,O 2,O I d 2,3 2,3 I d 2,7 2,7 5 d 3,7 3,7 I d 5 6,O min. 10% of nominal radius of wire 70 80 95 1 O0 110 125 Q BSI 052001 BS EN 10244-3900 1 BSI 389 Chiswick High Road London W4 4AL BSI - B

32、ritish Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level, It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users o

33、f British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary

34、of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying st

35、andards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at httxi:/www.bsi-. In response to orders for international standards, it is BSI policy to

36、supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Vario

37、us BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing memberdof BSI are kept up to date with standards developments and receive substantial discounts on the pu

38、rchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at httr,:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the cop

39、yright, in the TJK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or ot

40、herwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.