EN 10263-4-2017 en Steel rod bars and wire for cold heading and cold extrusion - Part 4 Technical delivery conditions for steels for quenching and tempering.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Steel rod, bars and wire for cold heading and cold extrusionPart 4: Technical delivery conditions for steels for quenching and temperingBS EN 102634:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10263-4 Novem

2、ber 2017 ICS 77.140.60; 77.140.65 Supersedes EN 10263-4:2001English Version Steel rod, bars and wire for cold heading and cold extrusion - Part 4: Technical delivery conditions for steels for quenching and tempering Barres, fil machine et fils en acier pour transformation froid et extrusion froid -

3、Partie 4: Conditions techniques de livraison des aciers pour trempe et revenu Walzdraht, Stbe und Draht aus Kaltstauch- und Kaltfliepresssthlen - Teil 4: Technische Lieferbedingungen fr Vergtungssthle This European Standard was approved by CEN on 26 July 2017. CEN members are bound to comply with th

4、e CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Managemen

5、t Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status

6、as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, N

7、etherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017

8、 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10263-4:2017 ENational forewordThis British Standard is the UK implementation of EN 102634:2017. It supersedes BS EN 102634:2001, which is withdrawn.The UK participation in its prepa

9、ration was entrusted to Technical Committee ISE/106, Wire Rod and Wire.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct appl

10、ication. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 85297 8ICS 77.140.65; 77.140.60Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and St

11、rategy Committee on 31 December 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 102634:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10263-4 November 2017 ICS 77.140.60; 77.140.65 Supersedes EN 10263-4:2001English Version Steel rod, bars and wire

12、 for cold heading and cold extrusion - Part 4: Technical delivery conditions for steels for quenching and tempering Barres, fil machine et fils en acier pour transformation froid et extrusion froid - Partie 4: Conditions techniques de livraison des aciers pour trempe et revenu Walzdraht, Stbe und Dr

13、aht aus Kaltstauch- und Kaltfliepresssthlen - Teil 4: Technische Lieferbedingungen fr Vergtungssthle This European Standard was approved by CEN on 26 July 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard

14、the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, Fr

15、ench, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgari

16、a, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerlan

17、d, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Mem

18、bers. Ref. No. EN 10263-4:2017 EBS EN 102634:2017EN 10263-4:2017 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Classification and designation 4 4.1 Classification . 4 4.2 Designation 4 5 Production Process . 4 5.1 Steelmaking process 4 5.2

19、 Deoxidation . 4 6 Requirements . 4 6.1 Delivery conditions 4 6.2 Chemical composition . 5 6.3 Mechanical properties . 5 6.4 Hardenability 5 6.5 Surface requirements 5 6.6 Supplementary or special requirements 5 BS EN 102634:2017EN 10263-4:2017 (E) 3 European foreword This document (EN 10263-4:2017)

20、 has been prepared by Technical Committee ECISS/TC 106 “Wire rod and wires”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2018, and conflicting na

21、tional standards shall be withdrawn at the latest by May 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10263-4:20

22、01. This European Standard EN 10263 is subdivided as follows: Part 1: General technical delivery conditions Part 2: Technical delivery conditions for steels not intended for heat treatment after cold working Part 3: Technical delivery conditions for case hardening steels Part 4: Technical delivery c

23、onditions for steels for quenching and tempering Part 5: Technical delivery conditions for stainless steels According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cr

24、oatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Tu

25、rkey and the United Kingdom. BS EN 102634:2017EN 10263-4:2017 (E) 4 1 Scope 1.1 This part of EN 10263 is applicable to round rod and round bars and wire with a diameter up to and including 100 mm, of non-alloy and alloy steel, intended for cold heading, cold extrusion, subsequent quenching and tempe

26、ring or induction hardening or flame hardening. 1.2 EN 10263-1:2017 is indispensable for this part of EN 10263. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the e

27、dition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10020, Definition and classification of grades of steel EN 10263-1:2017, Steel rod, bars and wire for cold heading and cold extrusion Part 1: General technical delivery

28、conditions 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10263-1:2017 and the following apply. 3.1 quenched and tempered steels engineering steels which, because of their chemical composition, are suitable for hardening and in the quenched and tempe

29、red condition to provide enhanced toughness at a given tensile strength 4 Classification and designation 4.1 Classification All steels covered by this part of EN 10263 are special steels according to EN 10020. Steel grades from C35EC to C45RC as quoted in Table 3 are non-alloy steels and all others

30、are alloy steels according to EN 10020. 4.2 Designation See EN 10263-1:2017. 5 Production Process 5.1 Steelmaking process See EN 10263-1:2017. 5.2 Deoxidation All steels according to this part of EN 10263 shall be deoxidised. 6 Requirements 6.1 Delivery conditions The delivery conditions in which th

31、e products covered by this part of EN 10263 are normally supplied, the product forms and the applicable requirements are given in Tables 1 and 2. BS EN 102634:2017EN 10263-4:2017 (E) 5 6.2 Chemical composition 6.2.1 Cast analysis The chemical composition for the cast analysis shall be in accordance

32、with the values specified in Tables 3 and 4. 6.2.2 Product analysis In cases where a product analysis is requested, the permissible deviations from the values specified for the cast analysis are indicated in Table 5. 6.3 Mechanical properties The mechanical properties of the products, to be determin

33、ed by the tensile test, shall be in accordance with the Tables 6, 7 and 8 but by considering the prescriptions given in Table 1 and the delivery condition given in Table 2. 6.4 Hardenability 6.4.1 In the case of products ordered with standard requirements regarding hardenability, that is, when the s

34、teel names or numbers as quoted in Tables 3 and 4 are supplemented by the symbol “+H”, the hardness values obtained in the end quench test (Jominy test) (see Table 1 of EN 10263-1:2017) shall be in compliance with the values given in Tables 9 and 11. 6.4.2 In the case of products ordered with restri

35、cted requirements regarding the scatter bands of the hardness values obtained by the Jominy test, that is when the steel name or number as quoted in Table 3 is supplemented by the symbol “+HH” or “+HL”, the above hardness values shall be in compliance with the values given in Table 10. NOTE 1 The sy

36、mbol “+HH” denotes that the upper limit of the scatter band coincides with the upper limit for the corresponding steel “+H”. NOTE 2 The symbol “+HL” denotes that the lower limit of the scatter band coincides with the lower limit for the corresponding steel “+H”. NOTE 3 See EN 10263-1:2017, 7.7.4 and

37、 10.2 6.4.3 The austenizing temperatures for the Jominy test are given in Tables 9, 10 and 11. 6.4.4 Core hardening In the case of products ordered with requirements for core hardening, that is when the steel name or number, as quoted in Tables 3 and 4 is supplemented by the symbol “+CH”, the core h

38、ardening temperature, the hardness values and the corresponding maximum diameters for the lowest hardenability shall be in compliance with the values given in Table 12. 6.5 Surface requirements For any particular surface requirement to be agreed at the time of ordering, see EN 10263-1:2017, 7.10. 6.

39、6 Supplementary or special requirements Other requirements which can be agreed at the time of enquiry and order are described in EN 10263-1:2017, Annex A. BS EN 102634:2017EN10263-4:2017(E)6Table1Summaryofdeliveryconditions,productformsand applicablerequirementsHeat-treatment conditionat deliverySym

40、bolProducts formApplicablerequirementsincaseswherethesteelconcerned hasbeenorderedwith referencetothesteelnamesindicated inbarrodwireTables 3and4,6or7or8Tables 3and4,6or7or8,9or10or11Tables 3and4,6or7or8,12Tables3,4,6,7,8,9,10,11or12untreatedNoneor+UXXChemicalcomposition asspecifiedinTables3and4Mech

41、anicalpropertiesasspecifiedin Table6or7 or8Chemicalcomposition asspecifiedinTables3and4Mechanicalpropertiesasspecifiedin Table6or7 or8Values forhardenabilityaccordingtoTables9 or10 or11Chemicalcomposition asspecifiedinTables3and4Mechanicalpropertiesasspecifiedin Table6or7 or8Minimumcorehardnessand m

42、aximum diameteraccordingtoTable12SupplementaryorspecialrequirementsasspecifiedinAnnexA of EN10263-1aspheroidised+ACXXXOthersOtherdeliveryconditionsmaybeagreedat thetimeoforderingKeyX=applicable=not applicableaIfagreedat thetimeoftheenquiryand order.BS EN 102634:2017EN10263-4:2017(E)7Table2Surfacecon

43、ditionatdeliverySurfaceconditionatdeliverySymbolbarrodwireUnlessotherwise agreedasrollednoneor+ARxxParticularsurfaceconditions suppliedbyagreementcolddrawn+Cxskinpassed+LCxxpeeled+PExxxBS EN 102634:2017EN10263-4:2017(E)8Table3Chemicalcompositionforsteelgradeswithoutboroncastanalysis %bymassSteelgrad

44、eCbSimaxaMnPmaxSCrMoNiCumaxSteelnameSteelnumberC35ECC35RCC45ECC45RC1.11721.10601.11921.10610,32to0,390.32to0,390,42to0,500,42to0,500,300,300,300,300,50to0,800,50to0,800,50to0,800,50to0,800,0250,0250,0250,0250,025max0.020to0,0350,025max0.020to0,0350,250,250,250,2537Mo21.54180,35to0,400,300,60to0,900,

45、0250,025max0,20to0,300,2538Cr246Cr234Cr437Cr441Cr441CrS41.70031.70061.70331.70341.70351.70390,35to0,420,42to0,500,30to0,370,34to0,410,38to0,450,38to0,450,300,300,300,300,300,300,50to0,800,50to0,800,60to0,900,60to0,900,60to0,900,60to0,900,0250,0250,0250,0250,0250,0250,025max0,025max0,025max0,025max0,

46、025max0.020to0,0400,40to0,600,40to0,600,90to1,200,90to1,200,90to1,200,90to1,200,250,250,250,250,250,2525CrMo425CrMoS434CrMo437CrMo442CrMo442CrMoS41.72181.72131.72201.72021.72251.72270,22to0,290,22to0,290,30to0,370,35to0,400,38to0,450,38to0,450,300,300,300,300,300,300,60to0,900,60to0,900,60to0,900,60

47、to0,900,60to0,900,60to0,900,0250,0250,0250,0250,0250,0250,025max0.020to0,0400,025max0,025max0,025max0.020to0,0400,90to1,200,90to1,200,90to1,200,90to1,200,90to1,200,90to1,200,15to0,300,15to0,300,15to0,300,15to0,300,15to0,300,15to0,300,250,250,250,250,250,2534CrNiMo641NiCrMo7321.65821.65630,30to0,380.

48、38to0,440,300,300,50to0,800,60to0,900,0250,0250,025max0,025max1,30to1,700,70to0,900,15to0,300,15to0,301,30to1,701,65to2,000,250,25aLowersiliconcontentsmaybeagreedat thetimeofordering, inwhich casedueconsiderationshouldbegiventotheeffectsthat couldresult forwhat concernsthespecifiedpropertiessuchas,

49、forexample, hardenability.bAcarbonrangeof0,04%(e.g. 0,33%-0,37%) maybe agreed atthe time ofenquiryand order.NOTE1Elementsnot quotedinthistableshouldnot beintentionallyaddedtothesteelwithout theagreement ofthepurchaser, except thoseintendedforfinishingtheheat. Allreasonableprecautionsshallbetakeninordertoprevent theadditionofsuch elementsfrom scraporothermaterialsusedintheproductionprocess, which mayaffect thehardenability, mechanicalpropertiesandapplicability.NOTE2Inthecaseofsteelswith hardenabilityrequirements(seeTables