1、BRITISH STANDARD Steel rod, bars and wire for cold heading and cold extrusion - Part 5: Technical delivery conditions for stainless steels The European Standard EN 10263-5:2001 has the status of a British Standard ICs 77.140.60; 77.140.65 BS EN 10263-5:200 1 Incorporating Corrigendum No. 1 NO COPYIN
2、G WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 10263-5:2001 13453 Corrigendum No. 1 National foreword 13 September 2001 This British Standard is the official English language version of EN 10263-5:2001. Together with BS EN 10263-1:2001 it supersedes BS 3111-2:1979 which is withd
3、rawn. The UK participation in its preparation was entrusted to Technical Committee ISE71, Steel rods for wire drawing, which has the responsibility to: - - aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change
4、, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or Eu
5、ropean publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the ne
6、cessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. This British Standard, having been prepared under the direction of the Engineering Sector Committe
7、e, was published under the authority of the Standards Committee and comes into effect on 15 August 2001 Summary Of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 11 and a back cover. The BSI copyright date displayed in this document indicates when t
8、he document was last issued. Amendments issued since publication Amd. No. IDate O BSI 13 September 2001 ISBN O 580 37624 9 Comments Addition of supersession details EUROPEAN STANDARD NORME EUROPENNE EUROPASCHE NORM EN 10263-5 June 2001 ICs 77.140.60: 77.140.65 English version Steel rod, bars and ste
9、el wire for cold heading and cold extrusion - Part 5: Technical delivery conditions for stainless steels Barres, fil machine et fils en acier pour transformation froid et extrusion froid - Partie 5: Conditions techniques de livraison des aciers inoxydables Walzdraht, Stbe und Draht aus Kaltstauch- u
10、nd Kalffliepresthlen - Teil 5: Technische Lieferbedingungen fr nichtrostende Sthle This European Standard was approved by CEN on 19 April 2001. CEN members are bound to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a n
11、ational standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in a
12、ny other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, German
13、y, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITI? EUROPBEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels O 2001 CEN All
14、rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10263-52001 E Page 2 Contents EN 10263-5:2001 Page Foreword . 3 1 2 3 4 4.1 4.2 5 6 6.1 6.2 6.3 6.4 6.5 Scope 4 Normative references 4 Terms and definitions . 4 Classification and designation
15、 4 Classification . 4 Designation . 4 Production Process 4 Requirements . 5 Delivery conditions 5 Chemical composition . 5 Surface quality 5 Supplementary or special requirements . 5 Mechanical properties . 5 O BSI 13 September 2001 Page 3 EN 10263-5:2001 O Foreword This European Standard has been p
16、repared by Technical Committee ECISSTC 15, Wire-rod - Qualities, dimensions, tolerances and specific tests, the Secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by
17、 December 2001, and conflicting national standards shall be withdrawn at the latest by December 2001. This European Standard EN 10263 is subdivided as follows: - Part I: General technical delivery conditions; - Part 2: Technical delivery conditions for steels not intended for heat treatment after co
18、ld working; - Part 3: Technical delivery conditions for case hardening steels; - Part 4: Technical delivery conditions for steels for quenching and tempering; - Part 5: Technical delivery conditions for stainless steels. According to the CENKENELEC Internal Regulations, the national standards organi
19、zations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. O BSI 13 September 200
20、1 1 Page 4 EN 10263-5:2001 1 Scope 1 .I intended for cold heading and cold extrusion having a diameter up to and including: - 25 mm for ferritic and austenitic-ferritic steels; - 50 mm for austenitic steels; - 1 O0 mm for martensitic steels. This part of EN 10263 is applicable to round rod, round ba
21、rs and wire made of stainless steels 1.2 This part of EN 10263 is complemented by EN 10263-1. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and t
22、he publications are listed hereafter. For dated references, subsequent amendments to or revisions of, any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (inc
23、luding amendments). EN 10020, Definitions and classification of grades of steel. EN 10088-1, Stainless steels - Part I: List of stainless steels. EN 10263-1, Steel rod, bars and wire for cold heading and cold extrusion - Part I: General technical delivery conditions. 3 Terms and definitions For the
24、purposes of this standard the definitions in EN 10263-1:2001 and the following apply. 3.1 stainless steels steels with at least 10,5 % of Cr and max. 1,2 % C are considered as stainless steels if their resistance to corrosion is of primary importance 4 Classification and designation 4.1 Classificati
25、on All steels covered by this part of EN 10263 standard are special alloy steel according to EN 10020. O From a practical viewpoint these steels are also classified on the basis of their structure, see also annex B of EN 10088-1 : 1995. 4.2 Designation See EN 10263-1:2001. 5 Production Process See E
26、N 10263-1 :2001 O BSI 13 September 2001 Page 5 EN 10263-512001 0 6 Requirements 6.1 Delivery conditions The delivery conditions in which the products covered by this part of EN 10263 are normally supplied, the product forms and the applicable requirements are given in Table 1. 6.2 Chemical compositi
27、on 6.2.1 Heat analysis The chemical composition shall be in accordance with the values specified in Table 2 for the heat analysis. 6.2.2 Product analysis In cases where a product analysis is requested, the admissible deviations from the values specified for the heat analysis are indicated in Table 3
28、. 6.3 Mechanical properties The mechanical properties of the products, to be determined by the tensile test, shall be in accordance with the prescriptionsgiien in Tables 4, 5, 6 and 7. 6.4 Surface quality 6.4.1 Rod is normally supplied in the pickled condition. Mechanical descaling (sandblasting) ca
29、n also be used, in which case a subsequent treatment in a pickling solution shall be carried out unless otherwise agreed. Particular processes such as peeling can also be applied, subject to specific agreement at the time of enquiry and order. 6.4.2 originating from rolled-in scale, shall not be reg
30、arded as defects. Minor surface imperfections that may occur under normal manufacturing conditions, such as scores 6.4.3 6.5 Supplementary or special requirements Any particular surface requirements may be agreed at the time of enquiry and order. 6.5.1 Aptitude to cold forming A test for the verific
31、ation of the aptitude of products to cold forming may be carried out if agreed at the time of enquiry and order. If for the verification of the aptitude to cold forming the upsetting test is applied, it shall be carried out as follows: - - a test piece with an initial length (height) equal to 13 d,
32、where d is the product diameter, is submitted to axial heading by means of a press until its length is reduced to 1/3 of the initial value. The above test shall be carried out at ambient temperature and limited to the products with a max. diameter of 15 mm. The criteria for the assessment of test re
33、sults shall be agreed at the time of ordering bearing in mind the end use for which the products are intended. 6.5.2 Depth of surface defects The max. admissible depth of surface defects is indicated in Table 8. The depth of a defect is considered as being the distance between the surface of the pro
34、duct and the bottom of the defect, to be measured in a direction perpendicular to the surface along a radius. In case of dispute the determination of the depth of surface defects shall be carried out by metallographic means with a magnification of X 100, on a straight cross-section of the product in
35、 the delivery condition concerned. O BSI 13 September 2001 - o) C .- 8 g .- E rc O c al m W al 5 c k m al C m o m C O W C n .- c .- 8 L. .- 5 - al U 8 3 - k E - C 3 2 8 u xx II II xx xx II I- $ ff +.$ -c cl K CK a a 3n !K -0.G 00- - c 83 + u) C c, ! p! a p! .- U a o P %! 2 .- - u) E c, E 2 a 2 n n .
36、- U a m o P m U C tu u) O o 3 w .- - E ic c, g u) z o 2 .- g 2 E O .- c, C - a w O ic 2 E S ua I i-“ r al n - I - X - X - I - X I X X X X X X X X f $ al 5 c m al o) ,m II II L! x I= mn Z W a u) u) E r P s 4- (II aa 5 E O u) O .- .- U ; o - lu o aa c o .- E m E lu u) aa m $i - aa aa G I im (Y aa n .-
37、 z I a o K E u3 K E n (II s K vj E o i a, O U e kj .- 2; =I v-c cc m noua Page 8 EN 10263-52001 Table 3 - Permissible deviations between product analysis and the limiting values specified in Limiting values of the cast (heat) analysis % by mass I 0,030 Elements Permissible deviation for the product
38、analysis % by mass + 0,005 C 0,030 I O ,I5 I1,OO l,oo I2,OO I l,oo si f 0,Ol + 0,05 + 0,lO + 0,03 Mn (00 I2,OO I 0,045 I 0,015 P f 0,04 + 0,005 + 0,003 S 0,015 I 0,030 I0,22 2 11,50 20,OO I23,OO I l,oo 1,OO I 4,OO 1,75 2 1,75 I 3,50 I1,OO 1,OO I 5,OO 5,OO I 10,OO 10,Oo I 14,OO Ni Ti f 0,20 f 0,25 +
39、0,07 f 0,lO f 0,05 f 0,lO + 0,03 f 0,07 f 0,lO f 0,15 I 0,70 I f 0,05 upper value or under the lower value of the specified range in Table 2, but not both at the same time. O BSI 13 September 2001 Page 9 EN 10263-512001 Steel name X6Crl7 X6CrMo 17-1 Table 4 - Mechanical properties for Ferritic Stain
40、less steels in the specified delivery condition Steel number 1.4016 1.41 13 1 Steel grade I Diameter Delivery condition +A+C+A I +A+C+A+LC Delivery condition +A+A+PE +A+LC I +A+C+A I +A+C+A+LC I 1 Mpa = lN/mrn I name X2CrNi MoN22- 5-3 Table 5 - Mechanical properties for Martensitic Stainless steels
41、in the specified delivery condition mm MPa % MPa % MPa % MPa % number rnm 950 55 1 O10 50 - 2 5 880 55 - 1.4462 5 10 880 55 1020 - 900 55 970 50 - 10 25 880 55 1 O00 - 880 55 - O BSI 13 September 2001 Page 10 EN 10263-5:2001 1 MPa = 1N/mm2 (continue4 O BSI 13 September 2001 Page 11 EN 10263-5:2001 S
42、teel grade Steel Steel name number Delivery condition Diameter +AT or +AT+C +AT+C+AT +AT+C+AT+L +AT+PE C Rm z Rm z Rm z Rm z mm mm MPa % MPa % MPa Yo MPa Yo above upto max. min. max. min. max. min. max. min. I1 MPa = lN/mmL I Diameter in the delivery conditiona mm Max. admissible depth of defectb mm
43、 I I10 I 0.10 I 10 a For diameter less than 5 mm, the permissible depth of surface defects shall be reduced in prportion of the I 1 % of the diameter reduction of the diamter during cold drawing. b For ferritic, martensitic and austenitic-ferritic steels, higher values may be agreed at the time of e
44、nquiry and order. O BSI 13 September 2001 BS EN 10263-5 :ZOO 1 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level.
45、 It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grat
46、eful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating servi
47、ce called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available f
48、rom the BSI website at httd/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national
49、, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1