1、STD-BSI BS EN LObS-ENGL 1999 W Lb24669 OBLZb87 019 m BRITISH STANDARD Adjustable telescopic steel props - Product specifications, design and assessment by calculation and tests The European Sandard EN 10651998 has the status of a British Standard ICs 91.220 BS EN 1065: 1999 NO COPYING WITHOUT BSI PE
2、RMISSION EXCEPT AS PERMITTED BY COPYRIGHI LAW STD-BSI BS EN LOb5-ENGL 1999 M Lb24669 O812b88 T55 BS EN 1065:1999 Amd. No. This British Standard, having been prepared under the direction of the Sector Committee for Building and Civil Engineering, was published under the authority of the Standards Com
3、mittee and comes into effect on 15 November 1999 Date Comments O BSI 11-1999 ISBN O 580 32838 4 National foreword This British Standard is the English language version of EN 1065:1998. The UK participation in its preparation was enirusted by Technical Committee B/514, Access and support equipment, t
4、o Subcommittee B/514/28, Props, tubes and couplers, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; - monitor related internation
5、al and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. This British Standard, together with BS 40741999 (in course preparation), will supersede BS 40741982, and partially supersede BS 550731982
6、 which is currently under revision. The revised edition of BS 5507-3 will descibe methods of determining the characteristic resistance of dustable props not conforming to BS EN 1065. BS 40741999 covers steel trench struts. This standard provides the user with a greatly enlarged choice of props. It i
7、s recommended, therefore, in the interests of maximizing site utilization, length compatibility with existing props, and as an aid to economic prop manufacture, that users should give preferential consideration to sizes 25,30,35,40 and 50 in either B or C strength grades and to either F2 or F4 corro
8、sion protection methods. Additionally, the use of loose forkheads is recommended. It is recommended that, if a pin has any reduction in its nominal cross section (such as holes for cables or chains), a means should be provided to ensure that this portion of the pin is always outside the collar nut m
9、ajor diameter. The principal changes from BS 40741982 and points of significance are as follows: a) Steel trench struts (previously known as trench struts) are not covered. b) Advice on safe working loads is not included. It is envisaged that the next amendment to BS 5975 will contain some advice. c
10、) Five different strength classes of props are included. Identification is now given by marking on each prop the number of the standard, the name or trademark of the manufacturer, the year of manufacture, the classification, and the props compatibility with EN 74 couplers. The prop may also have the
11、 classification identified by profiling the endplates. When required (see annex E) the level of inspection and/or the sign of the independent certification system also have to be marked. d) Five methods of corrosion protection are given. e) Props are classified according to their fully extended leng
12、ths which range from 2,5 m to 5,5 m in 0,5 m intervals. Fully closed lengths of props are no longer specified but all props have at least 1,0 m of adjustment. f, Props having a fully closed height of less than 1,5 m are no longer included. g) A test to venfy that the component parts of dustable tele
13、scopic steel props do not become inadvertently disengaged in use has been added. h) There is a minimum linear clearance of 100 mm between the inner and outer tubes intended to form an anti-hand trapping gap when the prop is in the fully closed position. i) The minimum permissible end plate bearing a
14、rea is reduced. j) A maximum clearance between threads is now specified. k) There is a minimum material thickness for ali prop components. 1) The use of rimming steel is no longer permitted. m) Geometric designed props are no longer included. n) Verification of the nominal characteristic resistance
15、of an individual prop design may also be by calculation. o) Information about independent prototype assessment is included in annex D. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogu
16、e under the section entitled “International Standards Correspondence Index“, or by using the “Find“ facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their corr
17、ect application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 34, an inside back cover and a back cover. The BSI copyright notice displayed in
18、 this document indicates when the document was last issued Amendments issued since publication STD-BSI BS EN LObS-ENGL 1999 Lb24bb9 O12b89 991 EUROPEAN STANDARD EN 1065 NORME EUROPENNE EUROPISCHE NORM September 1998 ICs Descriptors: building sites, scaffolding, props, steels, classifications, design
19、ation, corrosion prevention, adjustment, dimensions, mechanical strength, verification, computation, tests, marking English version Adjustable telescopic steel props - Product specif cations, design and assessment by calculation and tests Etais tklescopiques rglables en acier - Spcifications du prod
20、uit, conception et valuation par calculs et essais Bausttzen aus Stahl mit Ausziehvorrichtiing - Produktfestlegungen, Bemessung und Nachweis durch Berechnung und Versuche This European Standard was approved by CEN on 1 O June 1998. CEN members are bound to comply with the CENKENELEC Internal Regulat
21、ions which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This Euro
22、pean Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the nati
23、onal standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisch
24、es Komitee fr Normung Central Secretariat: rue de Stassart, 36 8-1050 Brussels O 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref. No. EN 1065:1998 E Page 2 EN 10651998 Con tents Page Foreword . 3 Introduction . 3 1 2 3 4 5 6 6.1 6.2 6.
25、3 7 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 7.10 8 9 9.1 9.2 9.3 9.4 9.5 10 10.1 10.2 10.3 10.4 11 12 Scope . 3 Normative references . 4 Definitions and symbols 6 Classification . 8 Designation 9 Materials 9 General 9 Modification by cold working . 9 Corrosion protection 10 Configuration 10 Tubes Weldin
26、g . Length adjustment device Permanent prevention against unintentional disengagement . Endplates . . Props with fixed forkheads . Anti hand trap . Minimum extended length Data required from the manufacturer 16 Overlapping length Nominal characteristic strength 16 Verification 16 General . 16 Verifi
27、cation of the actual characteristic strength by calculation . 17 Verification of the actual characteristic strength by testing 21 Verification of the strength of adjustment device . 21 Verification of the prevention against unintentional disengagement . 21 . 22 General Test method for the prop stren
28、gth . 22 Test of a pin and its supports . 25 Test of the prevention against unintentional disengagement 26 Test report 26 Marking . 27 Annex A (normative) Equations for the calculation of the structural properties of tubes . 28 Annex B (normative) Calculation of resistance for pin connections . 30 A
29、nnex C (normative) Statistical evaluation of data . 31 Annex 0 (informative) Prototype assessment 32 Annex E (informative) Ongoing production inspection 33 OBSI 11-1999 STD.BS1 BS EN 1065-ENGL 1999 1624669 0812691 54T Page 3 EN 1065:1998 Foreword This European Standard has been prepared by Technical
30、 Committee CENTTC 53, Temporary works equipment, the Secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 1999, and conflicting national standards shall be wi
31、thdrawn at the latest by March 1999. According to the CENCENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
32、Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Introduction Whilst this European Standard deals with the more common types of adjustable telescopic steel props in use, it is not intended to prevent development of other types of props. For example, props
33、 may have hinged ends or other length adjustment devices or be made of other materials Whilst such props cannot comply with this European Standard it is recommended that the principles of this European Standard be considered in the design and assessment of such props. The characteristic strength val
34、ues specified in this European Standard form a reference level which is unsafe for direct site use. It is a matter for a separate European Standard to relate these characteristic strengths to safe site usage by applying suitable partial safety factors yu and yF. It is also a matter for a separate Eu
35、ropean Standard to specify the required level of corrosion protection and inspection. This European Standard is a product standard primarily for use in the field of falsework and formwork. In cases where the prop is an integral part of a system of soffit support, other design and assessment procedur
36、es may be more appropriate or even necessary. This European Standard gives a number of alternatives, a designation of which is given in clause 5. 1 Scope This European Standard specifies materials, design requirements, corrosion protection alternatives together with assessment methods using both cal
37、culations and testing for open thread and covered thread adjustable telescopic steel props which are intended for use on construction sites (see Figure 1). It specifies five classes of nominal characteristic strengths for adjustable telescopic steel props each having a series of maximum extended len
38、gths. Each having differing endplate configuration. This European Standard does not apply to adjustable props of different materials or construction, nor does it provide any information concerning the use of adjustable steel props. OBSI 11-1999 Page 4 EN 1065:1998 / 4.2 a) Open thread (= DO) b) Cove
39、red thread (= DC) 4 Length adjustment device 5 Central hole 6 Connection holes 7 Pin hole X a) bl .2 Figure 1 : Adjustable telescopic steel prop 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references ar
40、e cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest e
41、dition of the publication referred to applies. EN 74 Couplers, loose spigots and base-plates for use in working scaffolds and falsework made of steel tubes - Requirements and test procedures EN 729-2 Quality requirements for welding - Fusion welding of metallic materials - Part 2: Comprehensive qual
42、ity requirements EN 1562 Founding - Malleable cast irons EN 1563 Founding - Spheroidal graphite cast irons EN 10002-1 Tensile testing of metallic materials - Method of test at ambient temperature EN 10025 Hot rolled products of non-alloy structural steels - Technical delivery conditions OBSI 11-1999
43、 STD-BSI BS EN LOb5-ENGL 1999 Lb24bb9 OBL2b93 312 Page 5 EN 1065:1998 EN 10083-1 Quenched and tempered steels - Pari 1 : Technical delivery conditions for special steels Quenched and tempered steels - Part 2: Technical delivery conditions for unalloyed quality steels EN 10083-2 EN 10083-3 Quenched a
44、nd tempered steels- Part 3: Technical delivery conditions for boron steels Hot-rolled products in weldable fine grain structural steels - Part 1 : General delivery conditions Hot-rolled products in weldable fine grain structural steels - Part 2: Delivery conditions for normalizedlnormalized rolled s
45、teels EN 10113-1 EN 10113-2 EN 10113-3 Hot-rolled products in weldable fine grain structural steels - Part 3: Delivery conditions for thermomechanical rolled steels EN 10155 Structural steels with improved atmospheric corrosion resistance -Technical delivery conditions Metallic products -Types of in
46、spection documents EN 10204 : 1991 EN 10210-1 Hot finished structural hollow sections of non-alloy and fine grain structural steels - Part 1 : Technical delivery requirements EN 10210-2 Hot finished structural hollow sections of non-alloy and fine grain structural steels - Part 2: Tolerances, dimens
47、ions and sectional properties EN 10219-1 Cold formed structural hollow sections of non-alloy and fine grain structural steels - Part 1 : Technical delivery requirements Cold formed structural hollow sections of non-alloy and fine grain structural steels - Part 2: Tolerances, dimensions and sectional
48、 properties Steel tubes for tube and coupler scaffold structures - Technical delivery conditions Eurocode 3: Design of steel structures - Part 1-1 : General rules and rules for buildings Quality systems - Model for quality assurance in design, development, production, installation and servicing EN 1
49、021 9-2 prEN 39 ENV 1993-1-1 EN IS0 9001 (IS0 9001 ) Quality systems - Model for quality assurance in production, installation and servicing (IS0 9002) EN IS0 9002 IS0 2937 Plain end seamless steel tubes for mechanical application Plain end seamless precision steel tubes -Technical conditions for delivery Plain end welded precision steel lubes -Technical conditions for delivery Plain end as-welded and sized precision steel lubes -Technical conditions for delivery IS0 3304 IS0 3305 IS0 3306 O BSI 11-1999 STDIBSI BS EN 1Ob5-ENGL 1997 M 1624bb9 0812b74 259 E Page 6 EN 1065:1998
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1