EN 1083-2-1997 en Power-Driven Brushes - Part 2 Safety Requirements《电刷 第2部分 安全要求》.pdf

1、STD-BSI BS EN 1083-2-ENGL 1777 m Lb24bb7 Ob37127 372 m BRITISH STANDARD Power-driven brushes Part 2. Safety requirements The European Standard EN 1083-2 : 1997 has the status of a British Standard ICs 25.100.70 NO COPYING WITHOUT ES1 PERMISSION EXCEPT AS PERMITTED BY COPYRIGH LAW BS EN 1083-2 : 1997

2、 BS EN 1083-2 : 1997 been prepared under the direction of the Consumer Amd. No. Dak Products and Services Sector Board, was published under the authority of the Standards Board and comes into effect on 15 September 1997 O BSI 1997 ISBN O 580 28310 O National foreword Text affected This British Stand

3、ard is the English language version of EN 1083-2 : 1997. Together with BS EN 10 - monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Sta

4、ndards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. Compliance with a B

5、ritish Standard does not of itself confer immunity from legal obligations. STD-BSI BS EN 1083-2-ENGL 1977 3b24bb7 Ob137321 T4O EUROPEAN STANDARD NORME EUROPEENNE EUROP b) the number of this European Standard, i.e. EN 1083-23) c) the maximum safe speed in revolutions per minute; d) the statement wear

6、 eye protection, or a symbol to that effect. NOTE. Additional relevant information may also be provided. following: Where, for reasons of size or material, it is impracticable to mark the brush, this information shall be given on its immediate packaging material. 6.2 Instructions Manufacturers shall

7、 provide mounting and safety instsuctions as follows. a) Brushes should not be mounted on machines having a speed in excess of the maximum permissible brush speed b) Damaged brushes should not be used. c) Rust discoloration or other signs of chemical or mechanical changes of the fill material may ca

8、use premature failure. d) Brushes should be stored in suitable racks, containers or boxes in such a manner that they are protected against the effects of: 1) high humidity, heat, water or other liquids which might cause damage to the brush; 2) exposure to acids, or fumes from acids, which might indu

9、ce deterioration; 3) any temperature low enough to cause condensation on the brush when removed from storage to an area of higher temperature; 4) distortion of any of the brush components. 3, Such marking is a claim of compliance with EN 1083-2 but does not imply CEN approval of the product; the acc

10、uracy of this claim is therefore solely the responsibility of the person applying the marking. O BSI 1997 BS EN 1083-2 : 1997 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the

11、 UK view on standards in Europe and at the intedonal level. It is incorporated by Royal Charter. Contract requirements A British Standard does not purport to include ail the necessary provisions of a contsact. Users of British Standards are responsible for their correct application. Revisions Britis

12、h Standards are updated by amendment* or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity whi

13、le using this British Standard would inform the Secretary of the responsible technical committee, the identity of which can be found on the inside front cover. Tel O181 996 9000; Fax: O181 996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automati

14、cally receive the Mest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services, Sales Department at Chiswick Tel O181 996 7000; Fax: O181 996 7001. In response to orders for international standards, it is B

15、SI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested Information on standards BSI provides a wide range of information on national, European and international standards through its Iibrary, the Standardline Database, the BSI In

16、formation Technology Service (BITS) and its Technical Help to Exporterc Service. Contact the Information Department at Chiswick Tel O181 996 7111; Fax: O181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of

17、 standards. For deW of these and other benefits contact Customer Services, Membership at Chiswick Tel O181 996 7002; Fax: O181 996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Exc

18、ept as permilked under the Copyright, Designs and Patents Act 1988 no eximct may be reproduced, stored in a rehied system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in

19、 the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained If permission is granted, the terms may include royal payments or a licensing agreement. Dem and advice can be obtained from the Copyright Manager, BSI, 389 Chiswick High Road, London W4 4AL.