EN 1173-2008 en Copper and copper alloys - Material condition designation《铜和铜合金 材料状态标识》.pdf

1、BRITISH STANDARDBS EN 1173:2008Copper and copper alloys Material condition designationICS 77.120.30g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58B

2、S EN 1173:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2008 BSI 2008ISBN 978 0 580 59371 0National forewordThis British Standard is the UK implementation of EN 1173:2008. It supersedes BS EN 1173:1996 which is withdrawn. The UK

3、 participation in its preparation was entrusted to Technical Committee NFE/34, Copper and copper alloys.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are

4、 responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1173April 2008ICS 77.120.30 Supersedes EN 1173:1995 English VersionCo

5、pper and copper alloys - Material condition designationCuivre et alliages de cuivre - Dsignation des tatsmtallurgiquesKupfer und Kupferlegierungen - ZustandsbezeichnungenThis European Standard was approved by CEN on 21 March 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulati

6、ons which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This Europe

7、an Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the nationa

8、l standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and Unite

9、d Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1173:2008: EEN 11

10、73:2008 (E) 2 Contents Page Foreword3 1 Scope 4 2 Basis of designation system 4 3 Structure of designation .4 3.1 General4 3.2 Position 14 3.3 Positions 2 to 4 5 3.4 Positions 5 and 6 .5 4 Examples 5 4.1 General5 4.2 Elongation 5 4.3 Spring bending limit 5 4.4 As drawn.5 4.5 Grain size5 4.6 Hardness

11、.6 4.7 As manufactured6 4.8 Tensile strength .6 4.9 0,2% proof strength .6 4.10 Additional treatment “Stress relieving“ 6 Bibliography 7 BS EN 1173:2008EN 1173:2008 (E) 3 Foreword This document (EN 1173:2008) has been prepared by Technical Committee CEN/TC 133 “Copper and copper alloys”, the secreta

12、riat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at the latest by October 2008. Attention is drawn

13、to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1173:1995. Within its programme of work, Technical Committee CEN/TC 133 decid

14、ed to prepare the revision of the fol-lowing standard: EN 1173:1995, Copper and copper alloys Material condition or temper designation In comparison with the first edition of EN 1173:1995, the following significant technical changes were made: title has been changed, the term “temper” has been withd

15、rawn; examples in Clause 4 have been completed; alloy designation in 4.10 has been corrected. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Re

16、pub-lic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 1173:2008EN 1173:2008 (E) 4 1 Scope This E

17、uropean Standard establishes a system for designation of material conditions to be used for the identifica-tion of mandatory property requirements. These designations are applicable to wrought products of copper and copper alloys. 2 Basis of designation system The material condition designation is b

18、ased on the mandatory property requirement(s), the level of property re-quired and if necessary, any special additional treatment. 3 Structure of designation 3.1 General The material condition designation usually consists of four characters. In position 1 there shall be a letter and in positions 2 t

19、o 4 there shall be figures. A further figure shall be added in position 5 or, in the case of additional treatment, a suffix letter shall be added in position 5 or 6. Only one designation is allowed for a certain material condition and the whole size range, for which the minimum requirement applies.

20、3.2 Position 1 Position 1 indicates the designating mandatory property, specified in the appropriate European product standard, by one capital letter of the alphabet. The use of a letter indicating the designating mandatory property does not preclude the combination of two or more mandatory properti

21、es if specified in the appropriate product standard. Letters shall be used in accordance with Table 1. Table 1 Letters for Position 1 Letter Designating mandatory property A Elongation B Spring bending limit D As drawn, without specified mechanical properties G Grain size H Hardness (Brinell or Vick

22、ers) M As manufactured, without specified mechanical properties R Tensile strength Y 0,2%-proof strength NOTE The manufacturing process including heat treatment is not indicated by these letters. BS EN 1173:2008EN 1173:2008 (E) 5 3.3 Positions 2 to 4 Except for designations D, G and M, positions 2 t

23、o 4 consist of a three digit figure to designate the minimum value of the mandatory property specified in the European product standard. Designations D and M are not fol-lowed by any further characters. For designation G, positions 2 to 4 consist of a three digit figure to designate the mid-range va

24、lue of the mandatory property specified in the European product standard. In the case of a value of two significant digits a zero “0“ is to be indicated at position 2 in front of the value speci-fied, e.g. for hardness. In the case of a value of one significant digit, zeros are to be indicated at po

25、sitions two and three in front of the value specified, e.g. for elongation. 3.4 Positions 5 and 6 If necessary a four digit figure may be indicated by use of the additional position 5, e.g. for very high tensile strength of precipitation hardened alloys. If an additional treatment is applicable for

26、the purpose of stress relieving a product, the suffix “S“ is added in position 5 or 6. 4 Examples 4.1 General The material condition designation is intended to be used in product designation and ordering information. In the product designation the material condition designation shall follow the mate

27、rial designation and be separated from it by a hyphen (“). Some examples of material condition designations in accordance with this standard are given in 4.2 to 4.10. 4.2 Elongation Wire EN 13602 Cu-OF A007 .1)7 4.3 Spring bending limit Strip EN 1654 CuSn8 B410 .1) 2 4.4 As drawn Tube EN 13600 Cu-ET

28、P D .1) 6 4.5 Grain size Strip EN 1652 CuZn37 G020 .1) 1 1) Continued according to the appropriate product standard, see Bibliography. BS EN 1173:2008EN 1173:2008 (E) 6 4.6 Hardness Sheet EN 1652 CuZn37 H150 .1) 1 4.7 As manufactured Hollow rod EN 12168 CuZn36Pb3 M .1) 4 4.8 Tensile strength Rod EN

29、12164 CuZn39Pb3 R500 .1) 3 or Strip EN 1652 CuBe2 R1200 .1) 1 4.9 0,2% proof strength Strip EN 1654 CuZn30 Y460 .1) 2 4.10 Additional treatment “Stress relieving“ Tube EN 12452 CuZn20Al2As R340S .1) 5 BS EN 1173:2008EN 1173:2008 (E) 7 Bibliography 1 EN 1652, Copper and copper alloys Plate, sheet, st

30、rip and circles for general purposes 2 EN 1654, Copper and copper alloys Strip for springs and connectors 3 EN 12164, Copper and copper alloys Rod for free machining purposes 4 EN 12168, Copper and copper alloys Hollow rod for free machining purposes 5 EN 12452, Copper and copper alloys Rolled, finn

31、ed, seamless tubes for heat exchangers 6 EN 13600, Copper and copper alloys Seamless copper tubes for electrical purposes 7 EN 13602, Copper and copper alloys Drawn round copper wire for the manufacture of electrical conductors BS EN 1173:2008BS EN 1173:2008BSI Group Headquarters389 Chiswick High Ro

32、ad,London W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards Institute (BSI)BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritis

33、h Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while

34、 using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400BSI offers members an individual updating service called PLUS which ensures that subscribers

35、automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the

36、BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European a

37、nd international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Sub

38、scribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding onli

39、ne access to British Standards via British Standards Online can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bo

40、dies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the fre

41、e use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070 Email: