EN 12152-2002 en Curtin Walling - Air Permeability - Performance Requirements and Classification《幕墙 透气率 性能要求和分类》.pdf

1、Curtain walling Air permeability Performance requirements and c1assii:ication The European Standard EN 12152:2002 has the status ofa British Standard ICs 91.060.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 12152:2002 BS EN 12152:2002 Amd. No. National foreword Date

2、 Comments This British Standard, having been prepared under the direction of the Building and Civil Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 26 March 2002 This British Standard is the official English langua

3、ge version of EN 12152:2002. The UKparticipation in its preparation was entrusted by Technical Committee B/53 8, Doors, windows, shutters, hardware and curtain walling, to Subcommittee B/538/6, Curtain walling, which has the responsibility to: - - aid enquirers to understand the text; present to the

4、 responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this subcommittee can be obtained on reque

5、st to its secretary. Cr oss-r e fer enc e s The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility

6、 of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligation

7、s. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 10, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. O BSI 26 March 2002 ISBN O 580 39416 6 EUROPEAN ST

8、ANDARD NORME EUROPENNE EUROPISCHE NORM EN 12152 February 2002 ICs 91.060.10 English version Curtain walling - Air permeability - Petformance requirements and classification Faades rideaux - Permabilit lair - Exigences de performance et classification Vorhangfassaden - Luftdurchlssigkeit - Leistungsa

9、nforderungen und Klassifizierung This European Standard was approved by CEN on 9 November 2001 CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-dat

10、e lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the re

11、sponsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Ma

12、lta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FR NORMUNG COMIT EUROPEN DE NORMALISATION Management Centre: rue de Stassart, 36 B-1050 Brussels O 2002 CEN All rights of exploitation in any form and by any

13、means reserved worldwide for CEN national Members. Ref. No. EN 12152:2002 E EN 12152:2002 (E) Contents Foreword . . 3 1 Scope 4 2 Normative references . 4 3 Terms and definitions . 4 4 Requirements . 5 5 Test method . 6 6 Class if icatio n . 6 . 10 Bib I i og ra p h y . 2 EN 12152:2002 (E) Foreword

14、This document EN 12152:2002 has been prepared by Technical Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical

15、text or by endorsement, at the latest by August 2002, and conflicting national standards shall be withdrawn at the latest by August 2002. This European Standard is part of a series of European Standards dedicated to curtain walling products and derives from performance requirements. This European St

16、andard forms part of a series of curtain walling standards as specified in the Product Standard prEN 13830. According to the CENICENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republ

17、ic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 3 EN 12152:2002 (E) 1 Scope This European Standard specifies requirements and classification of air permeability of both fixed

18、and openable parts of curtain walling, under positive and negative static air pressure. NOTE This European Standard applies to curtain walling as specified in prEN 13830. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. The

19、se normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For unda

20、ted references the latest edition of the publication referred to applies (including amendments). EN 121 53, Curtain walling -Air permeability - Test method. EN 12207, Windows and doors -Air permeability - Classification. prEN 131 19, Curtain walling - Terminology. prEN 13830, Curtain walling - Produ

21、ct Standard. ENV 1991 -2-4, Eurocode I: Basis of design and actions on structures - Part 2-4: Actions on structures - Wind action. 3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in prEN 13119 together with the following apply: 3.1 test pressure di

22、fferential air pressure between the two faces of the test specimen, expressed in Pascals (Pa) 3.2 positive pressure when the outer face is subjected to higher air pressure than the inner face 3.3 negative pressure when the outer face is subjected to lower air pressure than the inner face 3.4 air per

23、meability passage of air through the curtain walling when subjected to positive or negative air pressure The volume being expressed as a rate in cubic metres per hour (m3/h), this rate being related to the overall area of the curtain walling. Alternatively, the rate can be related to the metre lengt

24、h of joint. 4 EN 12152:2002 (E) 3.5 f xed joint all joints except openable joints of the curtain walling (see Figure 3) 3.6 fixed joint length sum of the length of all fixed joints within the curtain walling measured along the line of the air seal/barrier. Where a window is included within the curta

25、in walling, the length of the perimeter joint shall be included in the calculation (see Figure 3) 3.7 openable joint perimeters of all moving frames, in accordance with EN 12207 3.8 overall area sum of the areas of all the faces measured parallel to all fixed and openable panels (see Figure 2). It s

26、hall be expressed in m2 4 Req u rements 4.1 The air permeability for the fixed areas of the curtain walling shall take no account of the passage of air through openable joints and shall be related to the positive pressures applied and the overall area, or the fixed joint lengths, of the test specime

27、n. The air permeability per m2allowed for classification purposes is related to positive test pressures as shown in Table 1, and the air permeability per metre length of joint is related to positive test pressures as shown in Table 2. 4.2 Air permeability performance requirements of a curtain wall s

28、hall be established from Table 1 or Table 2 which are derived from maximum positive test pressures equating to 0,25 of the design wind load as determined in ENV 1991-2-4. For intermediate test pressures (P,) the air permeability allowed (O,) shall be determined using the formula: 213 Q no =Q E O, Pe

29、rmissible air permeablilty at intermediate positive test pressure P, O, Permissible air permeability at maximum positive test pressure Po 4.3 Where elevation layouts incorporate a large number of smaller pane units with associated mullions and transoms, it may be beneficial to express air permeabili

30、ty in terms of metre length of fixed joint, in lieu of m2 of curtain wall area. In such conditions Table 2 shall apply, based on 0,5 cubic metres per metre per hour (m3/m . h). 4.4 The air permeability for openable parts of curtain walling (e.g. windows within curtain walling facade) shall be relate

31、d to EN 12207. 5 EN 12152:2002 (E) 300 450 600 600 5 Test method The test specimen shall be tested in accordance with EN 12153. NOTE The test sequence as specified in prEN 13830 should be followed. 6 Classification Five classes are specified in order to adequately cover all location and regional con

32、diti experienced. (see Figure 1 and Table 1, or alternatively Table 2). 13 A2 13 A3 13 A4 13 AE ns likely to be Maxim um pressure pmax (Pa) 150 300 450 600 600 For the relevant class, the air permeability at the maximum test pressure indicated in Table 1 or Table 2, and the air permeability at the i

33、ntermediate test pressures specified in EN 12153 and calculated in accordance with 4.2, shall not exceed that allowed, through the entire range of specified test pressure steps. Air permeability Class m3/m . h 03 AI 03 A2 03 A3 03 A4 03 AE According to the results of the tests, the fixed element cur

34、tain walling product can be classified as indicated in Table 1, or alternatively in Table 2, and by reference to Figure 1. Table 1 -Air permeability classes (A) Based on overall area I Maxim um pressure I Air permeability I Class 6.1 Specimens which leak air 13 m3/m2. h at pressures 150 Pa cannot be

35、 classified. 6.2 Specimens which leak air Figure 1). 1,5 m3/m2. h at pressures 600 Pa are classified E (Exceptional) (see Table 2 -Air permeability classes (A) Based on fixed joint length 6.3 Specimens which leak air 0,5 m3/m . h at pressures 150 Pa cannot be classified. 6.4 Specimens which leak air

36、 Figure 1). 0,5 m3/m . h at pressures 600 Pa are classified E (Exceptional) (see 6 EN 12152:2002 (E) Cu E r v . c3 E 7 1.5 1 .o 0.8 0.6 O .4 - 1.15, - - -YI I / 0.72 / / 9 -i / / 50 1 O0 150 300 450 600 2 3 - nlrn 1 2 3 Pressure in Pascals (Pa). Fixed panel by area m3/m2. h Fixed panel by joint leng

37、th m3/m. h Figure 1 - CLASSIFICATION - Maximum permissible air permeability -0.5 -0.33 0.27 E -0.2 y r c3 E Cu -0.133 NOTE The exceptional category is attained when air permeability at all pressure steps is that for a higher performance class than A4, +IO %. 7 EN 12152:2002 (E) i , Total area = (a x

38、 j) + (a x m) + (b x k) + (d x k) + (c x n) + (c x e) + (c x f) +2(f x n) + (k - n x f) Figure 2 - Example of calculation of overall area 8 EN 12152:2002 (E) tt I I 0 4 2. 1 Fixed joint 2 Openable joint according to EN 12207 3 Openable panel 4 Fixed panel 1 I. Figure 3 - Example of fixed and openabl

39、e joint 9 EN 12152:2002 (E) Bibliography EN 1026, Windows and doors -Air permeability - Test method. 10 BS EN 12152:2002 BSI 389 Chiswick High Road Lon don w4 4AL BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at t

40、he international level. It is incorporated by Royal Charter. Re vi si ons British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and

41、services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offer

42、s members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +

43、44 (0)20 8996 7001. Email: orders&-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Informati

44、on on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the

45、Information Centre. Tel: +44 (0)20 8996 71 11. Fax: +44 (0)20 8996 7048. Email: infomi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details ofthese and other benefits contact Membership Administ

46、ration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 700 1. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyrigh

47、t subsists in all BSI publications. BSI also holds the copyright, in the UK, ofthe publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or

48、by any means - electronic, photocopying, recording or otherwise -without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, ofnecessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then the prior written permission ofBSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyright&-.