EN 12166-2016 en Copper and copper alloys - Wire for general purposes《铜和铜合金-一般用途的金属丝》.pdf

1、BS EN 12166:2016Copper and copper alloys Wire for general purposesBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 12166:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 12166:2016. It supersedes BS EN 12166:2011 which i

2、s withdrawn.The UK participation in its preparation was entrusted to Technical Committee NFE/34, Copper and copper alloys.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a c

3、ontract. Users are responsible for its correct application. The British Standards Institution 2016 .Published by BSI Standards Limited 2016ISBN 978 0 580 91265 8 ICS 77.150.30 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under t

4、he authority of the Standards Policy and Strategy Committee on 31 July 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 12166:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12166 July 2016 ICS 77.150.30 Supersedes EN 12166:2011English Version Copper and

5、copper alloys - Wire for general purposes Cuivre et alliages de cuivre - Fils pour usages gnraux Kupfer und Kupferlegierungen - Drhte zur allgemeinen Verwendung This European Standard was approved by CEN on 9 April 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which

6、 stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This Euro

7、pean Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members ar

8、e the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Ro

9、mania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and b

10、y any means reserved worldwide for CEN national Members. Ref. No. EN 12166:2016 EBS EN 12166:2016EN 12166:2016 (E) 2 Contents Page European foreword . 4 Introduction 6 1 Scope 7 2 Normative references 7 3 Terms and definitions . 7 4 Designation 8 4.1 Material . 8 4.1.1 General 8 4.1.2 Symbol . 8 4.1

11、.3 Number . 8 4.2 Material condition 8 4.3 Product 8 5 Ordering information . 10 6 Requirements 13 6.1 Composition . 13 6.2 Mechanical properties 13 6.3 Grain size . 13 6.4 Dimensions and tolerances 13 6.4.1 Diameter or width across-flats 13 6.4.2 Shape tolerances for round wire 13 6.4.3 Corner and

12、edge geometry (wire with square and rectangular cross-section only) 13 6.5 Joins . 14 6.6 Surface quality. 14 7 Sampling 14 7.1 General . 14 7.2 Analysis 14 7.3 Tensile, hardness and grain size tests 15 8 Test methods . 15 8.1 Analysis 15 8.2 Tensile test . 15 8.3 Hardness test . 15 8.4 Estimation o

13、f average grain size . 16 8.5 Retests 16 8.6 Rounding of results . 16 9 Declaration of conformity and inspection documentation . 16 9.1 Declaration of conformity . 16 9.2 Inspection documentation 17 10 Marking, packaging, labelling 17 Annex A (informative) Position of wire cross-section within a coi

14、l, reel, spool or drum . 40 Bibliography . 42 BS EN 12166:2016EN 12166:2016 (E) 3 Figures Figure 1 Calculation of corner radii 14 Figure A.1 Illustration of position of wire cross-section within the coil (bunched wound or stagger/traverse wound) . 40 Figure A.2 Illustration of position of wire cross

15、-section within the reel/spool/drum (stagger/traverse wound) . 40 Figure A.3 Illustration of position of wire cross-section within the coil (bunched wound or stagger/traverse wound) . 41 Figure A.4 Illustration of position of wire cross-section within the reel/spool/drum (stagger/traverse wound) . 4

16、1 Tables Table 1 Composition of low alloyed copper alloys 18 Table 2 Composition of copper-nickel-zinc alloys . 21 Table 3 Composition of copper-tin alloys . 21 Table 4 Composition of copper-zinc alloys 22 Table 5 Composition of copper-zinc-lead alloys 23 Table 6 Composition of complex copper-zinc a

17、lloys. 24 Table 7 Mechanical properties of wire of low alloyed copper alloys 24 Table 8 Mechanical properties of wire of copper-nickel-zinc alloys 27 Table 9 Mechanical properties of wire of copper-tin alloys 29 Table 10 Mechanical properties of wire of copper-zinc alloys . 31 Table 11 Mechanical pr

18、operties of wire of copper-zinc-lead alloys . 35 Table 12 Mechanical properties of wire of complex copper-zinc alloys . 36 Table 13 Grain size designations . 37 Table 14 Tolerances on diameter of round wire . 37 Table 15 Tolerances on width across-flats of square or regular polygonal wire . 38 Table

19、 16 Tolerances on width and thickness of rectangular wire 38 Table 17 Corner radii for square or rectangular wire . 39 Table 18 Sampling rate 39 BS EN 12166:2016EN 12166:2016 (E) 4 European foreword This document (EN 12166:2016) has been prepared by Technical Committee CEN/TC 133 “Copper and copper

20、alloys”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2017, and conflicting national standards shall be withdrawn at the latest by January 2017.

21、 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12166:2011. Within its programme of work, Technical Committee CEN/TC 133

22、 requested CEN/TC 133/WG 4 “Extruded and drawn products, forgings and scrap” to revise the following standard: EN 12166:2011, Copper and copper alloys Wire for general purposes. This document is one of a series of European Standards for the copper and copper alloy products rod, wire, profile and for

23、gings. Other products are specified as follows: EN 12163, Copper and copper alloys Rod for general purposes; EN 12164, Copper and copper alloys Rod for free machining purposes; EN 12165, Copper and copper alloys Wrought and unwrought forging stock; EN 12167, Copper and copper alloys Profiles and bar

24、s for general purposes; EN 12168, Copper and copper alloys Hollow rod for free machining purposes; EN 13601, Copper and copper alloys Copper rod, bar and wire for general electrical purposes; EN 13602, Copper and copper alloys Drawn, round copper wire for the manufacture of electrical conductors; EN

25、 13605, Copper and copper alloys Copper profiles and profiled wire for electrical purposes. In comparison with EN 12166:2011, the following significant technical changes were made: a) introduction of an optional procedure how to refer to restrictions to the chemical composition imposed by the 4 MS C

26、ommon Composition List for materials used for products accepted for contact with drinking water; b) provisions for surface quality added. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard:

27、Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, BS EN 12166:2016EN 12166:2016 (E) 5 Netherlands, Norway, Poland, Portugal, R

28、omania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 12166:2016EN 12166:2016 (E) 6 Introduction The European Committee for Standardization (CEN) draws attention to the fact that it is claimed that compliance with this document may involve the use of a patent c

29、oncerning the alloy CuZn21Si3P (CW724R) given in 6.1. CEN takes no position concerning the evidence, validity and scope of this patent right. The holder of this patent right has ensured the CEN that he is willing to negotiate licenses either free of charge or under reasonable and non-discriminatory

30、terms and conditions with applicants throughout the world. In this respect, the statement of the holder of this patent right is registered with CEN. Information may be obtained from: Wieland Werke AG Graf Arco Strae 36 D-89079 Ulm GERMANY Attention is drawn to the possibility that some of the elemen

31、ts of this document may be the subject of patent rights other than those identified above. CEN shall not be held responsible for identifying any or all such patent rights. CEN and CENELEC maintain online lists of patents relevant to their standards. Users are encouraged to consult the lists for the

32、most up to date information concerning patents (ftp:/ftp.cencenelec.eu/EN/IPR/Patents/IPRdeclaration.pdf). Due to developing legislation, the composition of a material may be restricted to the composition specified in this European Standard with respect to individual uses (e.g. for the use in contac

33、t with drinking water in some Member States of the European Union). These individual restrictions are not part of this European Standard. Nevertheless, for materials for which traditional and major uses are affected, these restrictions are indicated. The absence of an indication, however, does not i

34、mply that the material can be used in any application without any legal restriction. BS EN 12166:2016EN 12166:2016 (E) 7 1 Scope This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy wire, finally produced by drawing, rolling or extruding

35、, intended for general purposes, spring and fastener manufacturing applications. The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified. 2 Normative references The following documents, in whole or in part, are n

36、ormatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1173, Copper and copper alloys - Material condition des

37、ignation EN 1412, Copper and copper alloys - European numbering system EN 1655, Copper and copper alloys - Declarations of conformity EN 10204, Metallic products - Types of inspection documents EN ISO 2624, Copper and copper alloys - Estimation of average grain size (ISO 2624) EN ISO 6507-1, Metalli

38、c materials - Vickers hardness test - Part 1: Test method (ISO 6507-1) EN ISO 6892-1, Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1) ISO 1190-1, Copper and copper alloys Code of designation Part 1: Designation of materials 3 Terms and definitions For t

39、he purposes of this document, the following terms and definitions apply. 3.1 wire wound product of uniform cross-section along its whole length Note 1 to entry: Rectangles may have round or sharp corners. 3.2 deviation from circular form difference between the maximum and the minimum diameters measu

40、red at any one cross-section of a round product SOURCE: EN 12163:2016, 3.2 BS EN 12166:2016EN 12166:2016 (E) 8 4 Designation 4.1 Material 4.1.1 General The material is designated either by symbol or by number (see Tables 1 to 6). 4.1.2 Symbol The material symbol designation is based on the designati

41、on system given in ISO 1190-1. NOTE Although material symbol designations used in this standard might be the same as those in other standards using the designation system given in ISO 1190-1, the detailed composition requirements are not necessarily the same. 4.1.3 Number The material number designa

42、tion is in accordance with the system given in EN 1412. 4.2 Material condition For the purposes of this standard, the following designations, which are in accordance with the system given in EN 1173, apply for the material condition: M material condition for the product as manufactured, without spec

43、ified mechanical properties; R. material condition designated by the minimum value of tensile strength requirement for the product with mandatory tensile property requirements; H. material condition designated by the minimum value of Vickers hardness requirement for the product with mandatory hardne

44、ss requirements; S (suffix) material condition for a product which is stress relieved. G. material condition designated by the mid-range value of grain size requirement for the product with mandatory grain size requirements (Table 13). NOTE The G. material condition is normally applicable only to ro

45、und wires in the soft material condition made from alloys given in Tables 3, 4 and non-leaded alloys given in Table 2. Exact conversion between material conditions designated R., H. and G. is not possible. Except when the suffix S is used, material condition is designated by only one of the above de

46、signations. 4.3 Product The product designation provides a standardized pattern of designation from which a rapid and unequivocal description of a product can be conveyed in communication. It provides mutual comprehension at the international level with regard to products which meet the requirements

47、 of the relevant European Standard. The product designation is no substitute for the full content of the standard. The product designation for products to this standard shall consist of: denomination (Wire); BS EN 12166:2016EN 12166:2016 (E) 9 number of this European Standard (EN 12166); material de

48、signation, either symbol or number (see Tables 1 to 6); DW for compliance in the chemical composition according to the 4 MS Common Composition List. This information is mandatory in the case in which the product is used for drinking water applications according to the 4 MS Common Composition List an

49、d not to be given in other cases; material condition designation (see 4.2 and Tables 7 to 13); cross-sectional shape (the following designations shall be used as appropriate: RND for round, SQR for square, RCT for rectangular, HEX for hexagonal, OCT for octagonal, PFL for profile); nominal cross-sectional dimension(s) (or the number of the profile or a fully dimensioned and toleranced drawing); tolerance class for round, square or polygonal wire, (see Tables 14 and 15); fo