EN 12179-2000 en Curtain Walling - Resistance to Wind Load - Test Method《幕墙 抗风力性能的试验方法》.pdf

1、Curtain walling - Resistance to wind load - Test method The European Standard EN 12179:2000 has the status of a British Standard ICs 91.060.10 I IS EN .21792000 NO COPYING WITIIOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW National foreword been prepared under the direction of the Sector A

2、md.No. Committee for Building and Civil Engineering, was published under the authority of the Standards Committee and comes into effect on 15 August 2000 O BSI 082000 ISBN O 580 35787 2 This British Standard is the officiai English language version of EN 121792000. The UK participation in its prepar

3、ation was entrusted by Technical Committee B/538, Doors, windows, shutters, hardware and curtain walling, to Subcommittee B/538/6, Curtain walling, which has the responsibility to: Date Comments - aid enquirers to understand the text; - present to the responsible European committee any enquiries on

4、the - monitor related international and European developments and promulgate interpretation, or proposals for change, and keep the UK interests informed them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British

5、Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “Intemational Standards Correspondence Index“, or by using the “Find facility of the BSI Standards Eleclzonic Catalogue. A British Stan

6、dard does not purport to include ail the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover,

7、 an inside front cover, the EN title page, pages 2 to 9 and a back cover. The ES1 copyright notice displayed in this document indicates when the document was last issued. STD.BSI BS EN 12179-ENGL 2000 1624669 0866022 837 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12179 June 2000 ICs 91.060

8、.1 O English version Curtain walling - Resistance to wind load - Test method Faades rideaux - Rsistance la pression du vent - Mthode dessai Vorhangfassaden - Widerstand gegen Windlast - Prfverfahren This European Standard was approved by CEN on 6 October 1999. CEN members are bound to comply with th

9、e CEWCENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or

10、 to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versi

11、ons. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOM

12、ITEE FR NORMUNG COMITE EUROPEEN DE NORMALISATION Central Secretariat: rue de Stassart, 36 8-1050 Brussels Q 2000 CEN All rights of exploitation in any form and by any means resewed worldwide for CEN national Members. Ref. No. EN 12179:2000 E STD-BSI BS EN LZL79-ENGL 2000 LbZIbb9 0866023 773 H Page 2

13、 EN 121 79:2000 Con tents Foreword 3 1 2 3 4 5 6 7 a 9 10 Scope 4 Normative references. . 4 Definitions . 4 Principle 5 Apparatus 5 Test specimen . 6 Test preparation 6 Test procedure 6 Results 7 Test report . 7 O BSI 08-2000 STD-BSI BS EN lL2179-ENGL 2000 W Lh2qhh9 OBhh024 hOT Page 3 EN 12179:2000

14、Foreword This European Standard has been prepared by Technical Committee CEN/TC 33, Doors, windows, shutters, building hardware and curtain walling, the Secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identic

15、al text or by endorsement, at the latest by December 2000, and conflicting national standards shall be withdrawn at the latest by December 2000. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Stan

16、dard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. This European Standard forms part of a series of curtain walling tests as defined in the product s

17、tandard prEN 13830:2000. 8 BSI 08-2000 STD.BS1 BS EN 12179-ENGL 2000 1624669 0866025 546 Page 4 EN 121 79:2000 1 Scope This standard defines the method for determining the resistance to wind load of curtain walling, both its fixed and openable parts, under postive and negative static air pressure. N

18、OTE This standard applies to any curtain walling product as defined in prEN 13830:2000. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate points in the text and the pub

19、lications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these listed publications apply to this European Standard only when incorporated into it by amendment or revision. For undated references the latest edition of the publication referred to applies. p

20、rEN 13119: 1997 Curtain walling - Terminology. prEN 13116: 1997 Curtain walling - Resistance to wind load - Performance requirements. ENV 1991-2-4 Eurocode 1 : Basis of design and actions on structures - Part 2-4: Actions on structures - Wind actions. 3 Definitions For the purposes of this standard,

21、 the definitions given in prEN 13119:1997, together with the following, apply. 3.1 test pressure differential pressure between the two faces of the test specimen, expressed in Pascal (Pa) 3.2 posit ive pressure when outer face is subjected to higher pressure than inner face 3.3 negative pressure whe

22、n inner face is subjected to higher pressure than outer face 3.4 design wind load load calculated following the procedure specified within ENV 1991 -2-4 and represented in this test with positive and negative test pressures on the test specimen 3.5 increased load (safety load) I ,5 times design wind

23、 load expressed in Pascal O BSI 08-2000 STDaBSI BS EN LZL79-ENGL 2000 Lh2Ybh7 08hh02b 482 = Page 5 EN 121 79:2000 3.6 residual deformation change in shape or dimension which does not disappear when the test pressure is removed 3.7 frontal displacement movement of a point on a member measured normal

24、to the member 3.8 frontal deflection maximum frontal displacement of a member, minus half the sum of the frontal displacement at each end of the member 4 Principle Application of a sequence of test pressures (positive and negative) with displacements measured at each pressure. 5 Apparatus The test a

25、pparatus shall include the following. 5.1 A chamber with an opening into which the test specimen can be fitted. This chamber shall be of sufficient strength and rigidity to withstand the test pressures likely to be imposed during the tests. It shall not deflect under test pressure to any extent whic

26、h would affect the performance of the test specimen (Figure 1). Adequate representative structural supports shall be provided to which the specimen shall be attached in accordance with the conditions of use in the works (see also clause 6). The chamber shall be so constructed that the air permeabili

27、ty through it, at pressures up to the maximum air permeability test pressures, does not exceed the permissible air permeability through the specimen, at the same pressures. 5.2 A means for applying controlled positive and negative test pressures to the test specimen. 5.3 A means by which rapidly con

28、trolled changes of positive and negative test pressures may be produced within defined limits. 5.4 A means of measuring the applied positive and negative test pressures, steady or fluctuating, within an accuracy of 15 %. 5.5 Devices for measuring displacements to an accuracy of at least - name of th

29、e testing institute; - persons or persons requesting the test; - details of test specimen/s as follows: - type/s of construction; - profile references; O BSI 08-2000 Page 8 EN 121 79:2000 - origin of materials; - type/s of materials; - datek of manufacture, (if known); - dimensional drawing of speci

30、men/s; - the results of the test; - product designation from manufacturers literature; - observations as to the condition of the specimenk; - date of test; - date of calibration of test chamber and equipment; - date of report; - signature of person preparing the report. O BSI 08-2000 STD.BSI BS EN 1

31、2177-ENGL 2000 111 Lb2i1bb 08bb030 703 m Page 9 EN 121 79:2000 Enclosed surround to test chamber Simulated floor structur Test specimen E to chamber arou perimeter.- B B 31E it -4 Figure 1 - Example of test specimen built onto test chamber Q BSI 08-2000 BS EN 121 79:2000 BSI 389 Chiswick High Road L

32、ondon w4 4AL STD.BSI BS EN L2379-ENGL 2000 = Lb24bb9 0866033 84T BSI - British Standards Institution BSI is the independent national body responsible for preparing BriGh Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Rev

33、isions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or a

34、mbiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel 020 8996 9OOO. Fax: 020 8996 7400. BSI offers members an individual updating service caiied PLUS which ensures that subscrib

35、ers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel 020 8996 9001. Fax: O20 8996 7001. In response to orders for internaiional standards, it is BSI policy to su

36、pply the BSI implementation of those that have been published as British Standardc, unless otherwise requested Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Vaxious

37、BSI electronic information services are alCo available which give details on all its products and services. Contact the Information Centre. Tel 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purch

38、ase price of standards. For details of these and other benefits contact Membership Admhislxaiion. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Ex

39、cept as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free us

40、e, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the tem may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel O20 8996 7070.