EN 12192-1-2002 en Products and Systems for the Protection and Repair of Concrete Structures - Granulometry Analysis - Part 1 Test Method for Dry Components of Premixed Mortar《混凝土结.pdf

1、BRITISH STANDARD Products and systems for the protection and repair of concrete structures Granulometry analysis Part 1: Test method for dry components of premixed mortar The European Standard EN 12192-1:2002 has the status ofa British Standard ICs 91.080.40; 91.100.10 BS EN 12192-1 12002 NO COPYING

2、 WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 12192-112002 National foreword This British Standard is the official English language version of The UKparticipation in its preparation was entrusted by Technical Committee B/5 17, Concrete, to Subcommittee B/517/8, Protection and re

3、pair of concrete structures, which has the responsibility to: EN 12192-112002. This British Standard, having been prepared under the direction of the Building and Civil Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee

4、on 12 July 2002 - - aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the U

5、K. - A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “Internat

6、ional Standards Correspondence Index”, or by using the “Search”faci1ity ofthe BSI Electronic Catalogue or ofBritish Stan dards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for their correct application. Compliance with a Briti

7、sh Standard does not ofitself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 7 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendm

8、ents issued since publication Amd.No. I Date I Comments OBSI 12 July 2002 ISBN O 580 40084 O EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12192-1 May 2002 ICs 91.080.40; 91.100.10 English version Products and systems for the protection and repair of concrete structures - Granulometry analysi

9、s - Part 1 : Test method for dry components of premixed mortar Produits et systmes de protection et de rparation des structures en bton -Analyse granulomtrique - Partie 1: Mthode dessai applicable aux composants secs des mortiers prts lemploi Produkte und Systeme fr den Schutz und die Instandsetzung

10、 von Betontragwerken - Prfverfahren - Korngrenverteilung - Teil 1: Verfahren fr Trockenkomponenten von Fertigmrtel This European Standard was approved by CEN on 4 January 2002 CEN members are bound to comply with the CENLENELEC Internal Regulations which stipulate the conditions for giving this Euro

11、pean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English,

12、French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, D

13、enmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FR NORMUNG COMIT EUROPEN DE NORMALISATION Management Centre: rue de Stassart,

14、 36 B-I 050 Brussels O 2002 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12192-1:2002 E EN 12192-1 :2002 (E) Contents Page Foreword 3 1 2 3 4 5 6 7 7.1 7.2 7.3 8 9 Scope . .4 Normative references . . 4 Terms and definitions . Pr

15、inciple . Apparatus . 5 Sampling and preparation . Procedure . General Sieving Weighing . Express ion of res u Its . . 5 Test Report. . 2 EN 12192-1 :2002 (E) Foreword This document EN 12192-1 :2002 has been prepared by Technical Committee CEN/TC 104 ”Concrete and related products”, the secretariat

16、of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2002, and conflicting national standards shall be withdrawn at the latest by December 2002. It has been prepared b

17、y sub-committee 8 ”Products and systems for the protection and repair of concrete structures”, the secretariat of which is held by AFNOR. This European Standard describes a method for determining the particle size distribution of repair mortars, containing various water-dispersible components. It ha

18、s been adapted from EN 1015-1 ”Method of Test for mortar for masonry - Part 1 : Determination of particle size distribution” which is unsuitable for measurement of particle size for proprietary repair products and systems because they contain a variety of special additives, fibres and fillers. It is

19、 one of a series of inter-related parts dealing with granulometry size grading of products and systems for the protection and repair of concrete structures. The other part of this standard is: EN 121 92-2, Producfs and sysfems of fhe profecfion and repair of concrefe sfrucfures - Granulomefry analys

20、is- Par 2: Tesf mefhod for fillers for polymer bonding agenfs. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard : Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece

21、 Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 3 EN 12192-1 :2002 (E) 1 Scope This European Standard specifies a method for measuring the particle size distribution of the dry components of repair mortar mixes, being pa

22、rt of a repair product or system, as defined in prEN 1504-3, with a maximum particle size of 8 mm or 10 mm. Part 1 does not cover particle size distribution of separate aggregates, which should be determined in accordance with the test method described in EN 933 series. NOTE This standard gives a me

23、thod for granulometric analysis of fillers for polymer bonding agents. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are li

24、sted hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN

25、1504-1 , Producfs and sysfems for fhe profecfion and repair of concrefe sfrucfures - Definifions, requiremenfs, qualify con fro1 and evaluafion of conformify - Part 1: Definifions. EN 933-1, Tesfs for geomefrical properties of aggregafes - Part 1: Deferminafion of particle size disfribufion - Sievin

26、g mefhod. EN 933-2, Tesfs for geomefrical properties of aggregafes - Part 2: Deferminafion of particle size disfribufion - Tesf sieves, nominal size of apertures. EN 1015-2, Mefhod of fesf for mortar for masonry - Part 2: Bulk sampling of mortars and preparafion of fesf mortars. prEN 1504-3l, Produc

27、fs and sysfems for fhe profecfion and repair of concrefe sfrucfures - Part 3: Sfrucfural and non-sfrucfural repair. IS0 331 0-1, Tesf sieves - Technical requiremenfs and fesfing - Part 1: Tesf sieves of mefal wire clofh. 3 Terms and definitions For the purposes of this European Standard, the terms a

28、nd definitions contained in EN 1504-1 apply. 4 Principle Test sieves with increasing aperture size are nested on each other on top of a collection pan. The sample is placed on the top sieve and the stack of sieves agitated until the mass retained on each sieve remains constant. The retained mass is

29、then measured. NOTE of total mass. For samples with particles of different densities the sieve analysis will only give particle size distribution as a percent Under preparation. 4 EN 12192-1 :2002 (E) 5 Apparatus Table 1 -Aperture sizes of the test sieves (in mm) Series Al 8,OO 4,OO 2,oo 1 ,o0 I 0,5

30、00 I I 0,250 I O, 125 I 0,063 I Additional sieve aperture sizes (e.g. 5,6 mm, 0,09 mm) may be added when needed. Series R20 from IS0 565 may be used as an alternative. 5.1 Balance with a capacity of 1 kg and an accuracy of 0,l g. 5.2 shall not exceed 10 mm. The test sieves shall conform to the requi

31、rements of IS0 3310-1. Test sieves, with square apertures as specified in EN 933-2, are given in Table 1. The maximum aperture 5.3 Tightly fitting fines collection pan and lid, for the sieves. 5.4 Shallow trays, made of corrosion resistant metal, approximately 200 mm in diameter and 50 mm in height.

32、 5.5 Soft brush. 5.6 Ventilated oven, thermostatically controlled to maintain temperatures of (105 f 5) OC and (60 f 5) OC. 5.7 Sieving machine (optional). 6 Sampling and preparation The sample shall be taken in accordance with EN 1015-2. Reduction shall be carried out by use of a sample divider or

33、by quartering, yielding a test sample of mass larger than minimum value below, but not of an exact predetermined value. The minimum dry mass of the test sample shall be as follows: 0,3 kg for Dmax 2 4 mm; 0,6 kg for Dmax 4 mm. where Dmax = the maximum aggregate size of the sample in millimetres. Spr

34、ead the sample in a thin layer in shallow trays and dry in the oven at a temperature of (105 f 5) OC. With respect to the special constituents of repair mortars, a drying temperature of (60 f 5) OC may be used if recommended by the manufacturer. 5 EN 12192-1 :2002 (E) Continue the drying process unt

35、il two successive weighings of the sample at one day intervals do not differ by more than 1 g. 7 Procedure 7.1 General If mortars with lightweight or organic aggregates are tested, the material to be sieved may be statically charged by the motion of the material on the sieve, resulting in agglomerat

36、ion, or sticking to the sieve base. Should such a phenomenon occur, suitable measures should be taken to reduce this effect. 7.2 Sieving The dried sample shall be weighed immediately before sieving. The sample shall be placed on the top sieve of the nested sieves and the sieve-shaking procedure begu

37、n. NOTE sieving . Mechanical sieving is preferred, but manual sieving can be used if it produces the same results as mechanical Continue sieving until less than 1 % of the retained material (according to EN 933-1) will pass through any individual sieve during continuous hand sieving for one minute.

38、Do not force any material through the sieve by hand pressure. The use of a soft brush may be helpful if the mortar agglomerates. 7.3 Weighing Determine the mass of each fraction retained on the individual sieves and the fines collected in the pan. By addition, calculate the residual mass of the samp

39、le. Any difference between the original weight and the residual weight shall be added to the pan fines. NOTE 1 Some losses of very fine material into the air are likely to occur. On the sieves with apertures smaller than 4,OO mm, the fraction retained at the end of the sieving operation shall not ex

40、ceed the following: where m, is the mass, in grams of the fraction retained on the sieve; A is the area, in square millimetres, of the sieve; d is the nominal aperture size, in millimetres, of the sieve. If any of the fractions retained exceeds this amount, one of the two following procedures shall

41、be used: a) divide the fraction into proportions smaller than the specified maximum and sieve these one after the other; b) divide the portion of the sample passing through the 4,OO mm sieve with the aid of a sample divider or by quartering, and continue the sieve analysis on the reduced sample. NOT

42、E 2 To meet these requirements, completing the mechanical sieving by hand may be necessary. If the material to be sieved contains fibres, their proportion and type shall be recorded and described 6 EN 12192-1 :2002 (E) 8 Expression of results Calculate each individual retained fraction as percentage

43、 of the total mass of the sample, and express this as the percentage passing each sieve. If a dividing operation as described in 7.3 was carried out, this shall be taken into account in the calculation. NOTE A graphical presentation of the results can assist in making comparisons with manufacturers

44、production limits. 9 TestReport The test report shall include the following information: a reference to the test method standard; name and address of the test laboratory; identification number and date of the test; name and address of the manufacturer or supplier of the product; name and identificat

45、ion marks or batch number of the product; date of supply of the product; date of preparation of the test specimens and any deviation from the prescribed method of preparation; conditions of storage of prepared specimens prior to test; date of test and details of the test equipment used, including th

46、e make, type and capacity and the calibration details or the identification number of the apparatus, the total mass of each individual test sample, the method of sieving (by hand or mechanical means, etc.); the test results, including the percentage passing each sieve, and/or the cumulative percenta

47、ge of the mass of the total sample passing each sieve, to the nearest 1 %; if fibres are present, description of procedures used to identify nature and measure fibre content; precision data; date of test report and signature. 7 BS EN 12 192- 1 12002 B SI 389 Chiswick High Road London w4 4AL BSI -Bri

48、tish Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of

49、British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the late