EN 12285-1-2018 en Workshop fabricated steel tanks - Part 1 Horizontal cylindrical single skin and double skin tanks for the underground storage of flammable and nonflammable water.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Workshop fabricated steel tanksPart 1: Horizontal cylindrical single skin and double skin tanks for the underground storage of flammable and nonflammable water polluting liquids other than for heating and cooling of bui

2、ldingsBS EN 122851:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12285-1 July 2018 ICS 13.300; 23.020.10 Supersedes EN 12285-1:2003English Version Workshop fabricated steel tanks - Part 1: Horizontal cylindrical single skin and double skin tanks for the underground storage of flammable an

3、d nonflammable water polluting liquids other than for heating and cooling of buildings Rservoirs en acier fabriqus en atelier - Partie 1 : Rservoirs horizontaux cylindriques simple ou double paroi pour le stockage enterr de liquides inflammables et non inflammables polluant leau en dehors du chauffa

4、ge et du refroidissement des btiments Werksgefertigte Tanks aus Stahl - Teil 1: Liegende, zylindrische, ein- und doppelwandige Tanks zur unterirdischen Lagerung von brennbaren und nicht brennbaren wassergefhrdenden Flssigkeiten, die nicht fr das Heizen und Khlen von Gebuden vorgesehen sind This Euro

5、pean Standard was approved by CEN on 15 February 2018. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

6、concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN membe

7、r into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, Fran

8、ce, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPI

9、SCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12285-1:2018 ENational forewordThis British Standard is the UK implementation of EN

10、122851:2018. It supersedes BS EN 122851:2003, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PVE/15, Storage Tanks for the Petroleum Industry.A list of organizations represented on this committee can be obtained on request to its secretary.This public

11、ation does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 89308 7ICS 13.300; 23.020.10Compliance with a British Standard cannot confer i

12、mmunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 122851:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN

13、 12285-1 July 2018 ICS 13.300; 23.020.10 Supersedes EN 12285-1:2003English Version Workshop fabricated steel tanks - Part 1: Horizontal cylindrical single skin and double skin tanks for the underground storage of flammable and nonflammable water polluting liquids other than for heating and cooling o

14、f buildings Rservoirs en acier fabriqus en atelier - Partie 1 : Rservoirs horizontaux cylindriques simple ou double paroi pour le stockage enterr de liquides inflammables et non inflammables polluant leau en dehors du chauffage et du refroidissement des btiments Werksgefertigte Tanks aus Stahl - Tei

15、l 1: Liegende, zylindrische, ein- und doppelwandige Tanks zur unterirdischen Lagerung von brennbaren und nicht brennbaren wassergefhrdenden Flssigkeiten, die nicht fr das Heizen und Khlen von Gebuden vorgesehen sind This European Standard was approved by CEN on 15 February 2018. CEN members are boun

16、d to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CE

17、N-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre h

18、as the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, L

19、uxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Rue de la Science 2

20、3, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12285-1:2018 EBS EN 122851:2018EN 12285-1:2018 (E) 2 Contents Page European foreword . 4 1 Scope 5 2 Normative references 6 3 Terms, definitions, symbols and a

21、bbreviations . 6 3.1 Terms and definitions . 6 3.2 Symbols and abbreviations . 8 4 Product characteristics . 9 4.1 General 9 4.2 Welding . 9 4.2.1 Types of joints 9 4.2.2 Shell plate arrangement 12 4.2.3 Consumables 12 4.2.4 Interstitial space . 12 4.3 Load bearing capacity . 12 4.4 Additional requi

22、rements . 12 4.4.1 Manways and inspection covers . 12 4.4.2 Structural bolts . 13 4.4.3 Tank fittings, pipes and nozzles 13 4.4.4 Lifting lugs 14 4.5 Mechanical resistance and stability 15 4.5.1 Materials for shell, dished ends and manways 15 4.5.2 Wall thickness . 15 4.5.3 Stiffening resistance 17

23、4.5.4 Design of Stiffening Rings 18 4.6 Internal pressure . 19 4.7 Tightness (gas and liquid). 19 4.8 Release of dangerous substances . 19 4.9 Durability 19 4.10 Crushing resistance . 20 5 Testing and sampling methods . 20 5.1 Mechanical resistance and stability 20 5.1.1 Materials for shell, dished

24、ends and manways 20 5.1.2 Wall thickness . 20 5.1.3 Welding 20 5.1.4 Stiffening resistance 20 5.2 Load-bearing capacity 20 5.3 Tightness test (gas or liquid) . 21 5.4 Crushing resistance . 21 5.5 Testing of additional requirements. 21 5.5.1 Manways and inspection covers . 21 5.5.2 Structural bolts .

25、 21 5.5.3 Tank fittings, pipes and nozzles 21 5.5.4 Lifting lugs 21 5.6 Durability 22 BS EN 122851:2018EN 12285-1:2018 (E) 3 6 Classification 22 6.1 Tank type . 22 6.2 Tank classes 22 6.3 Designation and purchasers specification . 22 7 Marking and labelling . 23 7.1 Marking of the tank 23 7.2 Docume

26、ntation 23 8 Environmental aspects . 23 Annex A (informative) Transport, storage and installation procedure . 24 A.1 Transport . 24 A.2 Storage 24 A.3 Installation procedure 24 A.3.1 Planning . 24 A.3.2 Ground works 24 A.3.3 Backfill materials 25 A.3.4 Installing backfill 25 A.3.5 Access chamber . 2

27、6 Annex B (informative) Evaluation of liquid-material-combinations for storage tanks according to this standard 27 B.1 General . 27 B.2 Criteria for evaluation 27 B.2.1 Conditions for resistance . 27 B.2.2 Criteria for the suitability evaluation of liquid-material-combinations 29 B.3 Evaluation of l

28、iquids not mentioned in the positive-liquid-list . 29 B.4 Use of the positive-liquid-list . 29 B.4.1 Classification of the tanks according to their working conditions . 29 B.4.2 Conditions for the use of the liquids 30 Annex C (informative) Environmental aspects 114 Annex D (informative) A-deviation

29、s 117 Bibliography 119 BS EN 122851:2018EN 12285-1:2018 (E) 4 European foreword This document (EN 12285-1:2018) has been prepared by Technical Committee CEN/TC 265 “Metallic tanks for the storage of liquids”, the secretariat of which is held by BSI. This European Standard shall be given the status o

30、f a national standard, either by publication of an identical text or by endorsement, at the latest by January 2019, and conflicting national standards shall be withdrawn at the latest by April 2020. Attention is drawn to the possibility that some of the elements of this document may be the subject o

31、f patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document, together with prEN 12285-3:2016, supersedes EN 12285-1:2003. Compared to EN 12285-1:2003, this document has been revised as follows: exclusion of tanks covered by the Mandate M/131; old C

32、lause 3, Terms and definitions has been combined with old Clause 4, Symbols and abbreviations; old Clause 5, Designation and purchasers specification has been combined with new Clause 7, Classification and designation; old Clause 6, Materials, Clause 7, Design, Clause 8, Fabrication and Clause 10, H

33、andling and installation have been replaced by new Clause 4, Product characteristics; old Clause 9, Testing has now become Clause 5, Testing, assessment and sampling methods; old Clause 11, Marking of the tank and manufacturers statement has now been combined with new Clause 8, Marking, labelling an

34、d packaging. The informative Annexes A and B give further guidance: A on transport, storage and installation procedures and B on the liquid-material combinations to be chosen. Annex C provides guidance on environmental aspects. This European Standard Workshop fabricated steel tanks consists of 3 par

35、ts: Part 1: Horizontal cylindrical single skin and double skin tanks for the underground storage of flammable and nonflammable water polluting liquids other than for heating and cooling of buildings; Part 2: Horizontal cylindrical single skin and double skin tanks for the aboveground storage of flam

36、mable and non-flammable water polluting liquids; Part 3: Horizontal cylindrical single skin and double skin tanks for the underground storage of flammable and nonflammable water polluting liquids for heating and cooling of buildings. According to the CEN-CENELEC Internal Regulations, the national st

37、andards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

38、 Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 122851:2018EN 12285-1:2018 (E) 5 1 Scope This document specifies the product characteristics and test methods for workshop fabricated cylin

39、drical, horizontal steel tanks, single (type S) and double skin (type D) intended to be used for the underground storage of water polluting liquids (both flammable and non-flammable) and installed in industrial processes or in petrol stations at normal ambient temperature conditions (20 C to +50 C)

40、within the following limits: from 800 mm up to 3 000 mm nominal diameter and; up to a maximum overall length of 6 times the nominal diameter; with an operating pressure (Po) of maximum 50 kPa (0,5 bar(g) and minimum 5 kPa (50 mbar(g) and; for double skin tanks with a vacuum leak detection system whe

41、re the kinematic viscosity does not exceed 5 103m2/s. Tanks designed to this standard allow for an earth cover of up to 1,5 m. If there are imposed traffic loads or a greater earth cover, calculation is expected to be carried out. This document is not applicable to tanks used for storage and/or supp

42、ly of fuel/gas for building heating/cooling systems, and of hot or cold water not intended for human consumption, nor to loads and special measures necessary in areas subject to risk of earthquakes. Guidance on installation of tanks is presented in Annex A, which does not include special measures th

43、at might be necessary in areas subject to flooding. This document is not applicable for the storage of liquids having dangerous goods classes listed in Table 1 because of the special dangers involved. Table 1 List of dangerous goods which are not covered by this standard UN-classification Type of da

44、ngerous goods Class 1 Explosives Class 4.2 Substances liable to spontaneous combustion Class 4.3 Substances which in contact with water emit flammable gases Class 5.2 Organic peroxides Class 6.2 Infectious substances Class 7 Radioactive substances, hydrocyanic or hydrocyanic solvent liquids, metal c

45、arbons, hydrofluoric acid, bromide liquids NOTE The classifications referred to are those adopted by the United Nations Committee of Experts on the Transport of Dangerous Goods (not to be interpreted as tank classes described in 6.2). BS EN 122851:2018EN 12285-1:2018 (E) 6 2 Normative references The

46、 following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

47、EN 10025-2:2004, Hot rolled products of structural steels Part 2: Technical delivery conditions for non-alloy structural steels EN 10204:2004, Metallic products - Types of inspection documents EN 13160-1, Leak detection systems Part 1: General Principles EN 13160-2, Leak detection systems Part 2: Re

48、quirements and test/assessment methods for pressure and vacuum systems EN 13160-3, Leak detection systems Part 3: Requirements and test/assessment methods for liquid systems for tanks EN 22768 (all parts), General tolerances (ISO 2768 series) EN ISO 898-1, Mechanical properties of fasteners made of

49、carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1) EN ISO 12944-7, Paints and varnishes - Corrosion protection of steel structures by protective paint systems Part 7: Execution and supervision of paint work (ISO 12944-7) EN ISO 13920, Welding - General tolerances for welded constructions - Dimensions for lengths and angles - Shape and position (ISO 13920) 3 Terms, definitions, symbols and abbrevia