EN 12312-10-2005 en Aircraft ground support equipment - Specific requirements - Part 10 Container Pallet transfer transporters (Incorporates Amendment A1 2009)《航空地面辅助设备 特殊要求 第10部分 .pdf

1、BRITISH STANDARD BS EN 12312-10:2005Aircraft ground support equipment Specificrequirements Part 10: Container/Pallet transfer transportersICS 49.100g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39

2、g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58+A1:2009This British Standard was published under the authority of the Standards Policy and Strategy Committeeon 27 February 2006 BSI 2009National forewordBS EN 12312-10:2005+A1:2009EN 12312-10:2005+A1:2009. It supersedes BS EN 12312-10:2005 which is w

3、ithdrawn.The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of CEN amendment. For example, text altered by CEN amendment A1 is indicated by a b.The UK participation in its preparation was entrusted to

4、 Technical Committee ACE/57, Air cargo and ground support equipment.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct applica

5、tion.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate Comments ISBN 978 0 580 61365 4This British Standard is the UK implementation of the 30 June 2009 Implementation of CEN amendment A1:2009EUROPEAN STANDARD NORME EU

6、ROPENNE EUROPISCHE NORM EN 12312-10:2005+A1 April 2009 ICS 49.100 Supersedes EN 12312-10:2005English Version Aircraft ground support equipment - Specific requirements - Part 10: Container/Pallet transfer transporters Matriel au sol pour aronefs - Exigences particulires - Partie 10: Transporteurs de

7、conteneurs et de palettes Luftfahrt-Bodengerte - Besondere Anforderungen - Teil 10: Container-/Paletten-Transfer-Transporter This European Standard was approved by CEN on 13 June 2005 and includes Amendment 1 approved by CEN on 1 March 2009. CEN members are bound to comply with the CEN/CENELEC Inter

8、nal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN memb

9、er. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN membe

10、rs are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, S

11、witzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I T E U R O P E N D E N O R M A LI S A T I O N EUR OP IS C HES KOM ITEE FR NOR M UNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide fo

12、r CEN national Members. Ref. No. EN 12312-10:2005+A1:2009: EEN 12312-10:2005+A1:2009 (E) 2 Contents Page Foreword 3g3Introduction . 4g31g3 Scope 5g32g3 Normative references 6g33g3 Terms and definitions . 6g34g3 List of hazards 6g35g3 Safety requirements and/or measures 7g35.1g3 General requirements

13、7g35.2g3 Platform design, guide rails and stops 7g35.3g3 Operation 8g35.4g3 Transportability 8g35.5g3 Drive systems and mobility 8g35.6g3 Drivers accommodation . 8g35.7g3 Emergency stops . 9g35.8g3 Operating speeds. 9g35.9g3 Options . 9g36g3 Information for use 9g36.1g3 Marking . 9g36.2g3 Warnings .

14、 9g36.3g3 Instructions 9g37g3 Verification of requirements . 10g3Annex A (informative) Examples of different transporters . 11g3Annex B (normative) List of hazards in addition to those of EN 1915-1 13g3Annex C (informative) Functional requirements for conveying systems on platforms . 14g3Annex D (in

15、formative) Typical data for unit load devices . 16g3Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC 18g3Annex ZB (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 2006/4

16、2/EC“ . 19g3Bibliography 20g3BS EN 12312-10:2005+A1:2009 EN 12312-10:2005+A1:2009 (E) 3 Foreword This document (EN 12312-10:2005+A1:2009) has been prepared by Technical Committee CEN/TC 274, “Aircraft ground support equipment“, the secretariat of which is held by DIN. This European Standard shall be

17、 given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the latest by December 2009. This document includes Amendment 1, approved by CEN on 2009-03-01. This documen

18、t supersedes EN 12312-10:2005. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! “. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association and supports essential require

19、ments of EU Directive(s). !For relationship with EU Directives, see informative Annexes ZA and ZB, which are integral parts of this document.“ The Parts of EN 12312 Aircraft ground support equipment Specific requirements are: Part 1: Passenger stairs Part 2: Catering vehicles Part 3: Conveyor belt v

20、ehicles Part 4: Passenger boarding bridges Part 5: Aircraft fuelling equipment Part 6: Deicers and deicing/antiicing equipment Part 7: Air-craft movement equipment Part 8: Maintenance stairs and platforms Part 9: Container/Pallet loaders Part 10: Container/Pallet transfer transporters Part 11: Conta

21、iner/Pallet dollies and loose load trailers Part 12: Potable water service equipment Part 13: Lavatory service equipment Part 14: Disabled/Incapacitated passenger boarding equipment Part 15: Baggage and equipment tractors Part 16: Air start equipment Part 17: Air conditioning equipment Part 18: Nitr

22、ogen or Oxygen units Part 19: Aircraft jacks, axle jacks and hydraulic tail stanchions Part 20: Ground power equipment According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, B

23、ulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 12312-10:2005+A1:2009

24、EN 12312-10:2005+A1:2009 (E) 4 Introduction This European Standard specifies health and safety requirements, as well as some functional and performance requirements for container/pallet transfer transporters intended for moving unit load devices (ULD) on an airport. The minimum essential criteria ar

25、e considered to be of primary importance in providing safe, serviceable, economical and practical container/pallet transfer transporters. Deviations from the recommended criteria should occur only after careful consideration, extensive testing, risk assessment and thorough service evaluation have sh

26、own alternative methods or conditions to be satisfactory. This European Standard is a Type C standard as stated in EN ISO 12100. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this European Standard. When provisions

27、of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this type C standard. BS EN 123

28、12-10:2005+A1:2009 EN 12312-10:2005+A1:2009 (E) 5 1 Scope This European Standard specifies the technical requirements to minimise the hazards listed in Clause 4 which can arise during the commissioning, operation and maintenance of container/pallet transfer transporters when carried out in accordanc

29、e with the specifications given by the manufacturer or his authorised representative. It also takes into account some performance requirements recognised as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines and handling agencies. This European St

30、andard applies to self-propelled container/pallet transfer transporters, with a seated driver. Examples of typical transfer transporters are shown in Annex A. This European Standard does not apply to: loading equipment with a height adjustment capability in excess of 150 mm; transporter-loaders (sin

31、gle platform loader with transporter capability, see EN 12312-9); roller-bed transport platforms mounted on unmodified commercial road chassis. This European Standard does not establish requirements for noise and vibration. Noise and vibration are dealt with respectively in EN 1915-4 and EN 1915-3.

32、This European Standard is not dealing with hazards in respect to a standard automotive chassis and the traffic on the apron. This Part of EN 12312 is not applicable to GSE which are manufactured before the date of publication by CEN of this European Standard. NOTE Certain measurements have been give

33、n in imperial units (in parentheses) following the metric measurements since the containers/pallets to be handled are based mainly on the imperial system. !This part of EN 12312 is intended to be used in conjunction with EN 1915-1, EN 1915-2, EN 1915-3 (for vehicles) and EN 1915-4.“ BS EN 12312-10:2

34、005+A1:2009 EN 12312-10:2005+A1:2009 (E) 6 2 Normative references The following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including

35、 any amendments) applies. !deleted text“ EN 1050:1996, Safety of machinery Principles for risk assessment EN 1915-1:2001, Aircraft ground support equipment General requirements Part 1: Basic safety requirements EN 1915-2, Aircraft ground support equipment General requirements Part 2: Stability and s

36、trength requirements, calculations and test methods !EN 1915-3, Aircraft ground support equipment General requirements Part 3: Vibration measurement methods and reduction EN 1915-4, Aircraft ground support equipment General requirements Part 4: Noise measurement methods and reduction“ EN ISO 12100-1

37、2003, Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles (ISO 12100-2:2003) !EN ISO 13850:2008, Safety of mach

38、inery Emergency stop Principles for design (ISO 13850:2006)“ ISO 2328, Fork-lift trucks Hook-on type fork arms and fork arm carriages Mounting dimensions !ISO 10254“, Air cargo and ground equipment Vocabulary 3 Terms and definitions For the purposes of this European Standard, the terms and definitio

39、ns given in EN 1915-1:2001, EN ISO 12100:2003 and the following apply. 3.1 transfer transporter self-propelled GSE capable of transporting and transferring ULDs 3.2 container completely enclosed ULD for use on aircraft that interfaces directly with the aircraft cargo handling and restraint system (s

40、ee also !ISO 10254“) 3.3 pallet ULD for use on aircraft, consisting of a flat platform with flat undersurface of standard dimensions on which goods are assembled and secured before being loaded as a unit onto the aircraft and which interfaces directly with the aircraft handling and restraint system

41、see also !ISO 10254“) 4 List of hazards The list of risks and hazards (see Annex B) is based on EN 1050 and contains the hazards and hazardous situations, as far as they are dealt with in this European Standard, identified by risk assessment as significant for container/pallet transfer transporters

42、 and which require action to eliminate or reduce risks. BS EN 12312-10:2005+A1:2009 EN 12312-10:2005+A1:2009 (E) 7 5 Safety requirements and/or measures 5.1 General requirements 5.1.1 !Container/Pallet transfer transporters shall conform to the relevant requirements of EN 1915-1, EN 1915-2, EN 1915-

43、3 and EN 1915-4 unless otherwise specified in this standard.“ They shall also conform to the specific requirements of this European Standard. 5.1.2 Strength calculations shall be carried out in accordance with EN 1915-2. 5.2 Platform design, guide rails and stops 5.2.1 Platform design 5.2.1.1 The tr

44、ansporter shall provide a rollerized, or equivalent, platform capable of transferring ULDs. The platform shall be adjustable in height to permit alignment with other ULD handling/storage systems having a nominal interface height of 508 mm (20 in). NOTE Typically, the range of adjustment may be betwe

45、en 450 mm and 580 mm (18 in and 23 in) from the ground. 5.2.1.2 Roller systems shall meet the requirements given in Annex C. NOTE Typical container and pallet overall dimensions and masses are given in Annex D. 5.2.1.3 The conveyor system shall be designed such that it takes into account the mating

46、of two items of GSE. 5.2.1.4 A lead-in edge or roller, or equivalent, shall be provided commensurate with the design of the transporter, in order to absorb the initial impact of transferring ULDs. 5.2.1.5 All walkways, beams or other structures shall be at least 13 mm (0,5 in) below the tops of the

47、conveying surface. 5.2.1.6 The transporter shall be so designed as to minimize the risk of damaging the ULD, e.g. by the avoidance of projections or sharp corners. 5.2.2 Guides and stops 5.2.2.1 Guides shall be provided as follows: Fixed side guide rails shall be provided on the platform suitably sp

48、aced to cater for the widest ULD to be carried; Guide rails shall have a minimum height of 100 mm (4 in) above the conveying surface; Funnel shaped lead-ins shall be provided at both ends. 5.2.2.2 Stops shall be provided as follows: Roll-off stops shall be incorporated on both ends of the transporte

49、r to preclude inadvertent movement of a ULD off the conveying system. Forward and aft stops shall be provided capable of containing all the ULDs to be transported; All stops shall have a minimum height of 50 mm (2 in) above the conveying surface; The maximum centre to centre distance between two stops on one end shall be less than the width of the smallest ULD to be transported; The minimum width of a stop shall be 50 mm (2 in) where practicable. BS EN 12312-10:2005+A1:2009 EN 12312-10:2005+A1:2009 (E) 8 NOTE For t