EN 12320-2012 en Building hardware - Padlocks and padlock fittings - Requirements and test methods《构建硬件-挂锁和挂锁配件要求和测试方法》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 12320:2012Building hardware Padlocksand padlock fittings Requirements and testmethodsBS EN 12320:2012 BRITISH STANDARDNational forewordThis British Standard is the UK imple

2、mentation of EN 12320:2012. Itsupersedes BS EN 12320:2001 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/538/4, Building hardware.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does n

3、ot purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 67831 8ICS 91.190Compliance with a British Standard cannot confer immunity fromlegal obligat

4、ions.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 October 2012.Amendments issued since publicationDate Text affectedBS EN 12320:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12320 October 2012 ICS 91.190 Supersedes EN 12320:20

5、01English Version Building hardware - Padlocks and padlock fittings - Requirements and test methods Quincaillerie pour le btiment - Cadenas et porte-cadenas -Exigences et mthodes dessai Baubeschlge - Hangschlsser und Hangschlossbeschlge - Anforderungen und Prfverfahren This European Standard was app

6、roved by CEN on 11 August 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationa

7、l standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language

8、 and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hu

9、ngary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Manage

10、ment Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12320:2012: EBS EN 12320:2012EN 12320:2012 (E) 2 Contents Page Foreword . 31 Scope 42 Normative references 43 Terms and definitions

11、 . 44 Requirements . 65 Test methods . 86 Classification . 167 Marking . 17Annex A (normative) Sampling and sequencing - Tests on alternative design padlocks 18Annex B (normative) Test rig illustrations 19BS EN 12320:2012EN 12320:2012 (E) 3 Foreword This document (EN 12320:2012) has been prepared by

12、 Technical Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2

13、013, and conflicting national standards shall be withdrawn at the latest by April 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights

14、. This document supersedes EN 12320:2001. The following is a list of technical changes since the previous edition: - Limited manual attack - Corrosion resistance - Table 2 security requirements - Resistance to attack by plug/cylinder extraction - Annex A, sampling and sequencing The test methods are

15、 specified in detail to ensure reproducibility at any testing establishment within Europe, and the acceptance criteria are defined objectively to ensure consistency of assessment. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are b

16、ound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portu

17、gal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 12320:2012EN 12320:2012 (E) 4 1 Scope This European Standard applies to mechanical padlocks and padlock fittings used on buildings and general use and specifies the test methods to be used. This Europe

18、an Standard specifies performance and other requirements for strength, security, durability, performance, and corrosion resistance of padlocks. It establishes one category of use, two categories of durability, six categories for corrosion resistance and six grades for security based on performance t

19、ests that simulate attack. Limited manual attack testing is included in this European Standard because the machine testing does not replicate all known manual attacks. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensab

20、le for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1303:2005, Building hardware Cylinders for locks Requirements and test methods EN 1670:2007, Building hardware Co

21、rrosion resistance Requirements and test methods EN 10025-2, Hot rolled products of structural steels Part 2: Technical delivery conditions for non-alloy structural steels ISO 10899, High-speed steel two-flute twist drills Technical specifications 3 Terms and definitions For the purposes of this doc

22、ument, the following terms and definitions and symbols apply. 3.1 Terms and definitions 3.1.1 cam part of the key and cylinder mechanism which operates the locking mechanism 3.1.2 effective key differ difference between the key mechanism of similar design, achieved only by the movable detainer, whic

23、h allows each key mechanism to be operated only by its own key Note 1 to entry: The number of effective differs is equal to the number of theoretical differs after deduction of the differs suppressed by the manufacturer due to technical constraints and those differs suppressed in accordance with the

24、 restraints of 4.5.1 3.1.3 hasp part of the padlock fitting which goes over the staple. BS EN 12320:2012EN 12320:2012 (E) 5 3.1.4 key mechanism part of the mechanism which recognises a correct key 3.1.5 locking mechanism part of the mechanism which is operated by the key mechanism to lock/unlock the

25、 padlock 3.1.6 padlock independent locking device comprising a body, a key mechanism, a locking mechanism and a shackle 3.1.7 padlock fitting device fitted to the object which is to be locked with a padlock excluding cables and chains 3.1.8 shackle part of the padlock which passes through and secure

26、s the padlock fitting 3.1.9 staple part of the padlock fitting through which the padlock shackle is passed. 3.2 Symbols Table 1 Symbol Unit Definitiond mm Diameter of shackle F1 kN Push/pull force on cylinder plug/locking mechanism F2 kN Pull force on shackle or staple F3 kN Cutting force on shackle

27、 or staple F4 kN Maximum possible push/pull force on cylinder plug/locking mechanismh mm Height through which weight is dropped (impact test) M1 Nm Torque on key to test for interpassing M2 Nm Torque on cylinder plug/locking mechanism M3 Nm Twisting torque on shackle or staple n Minimum number of ef

28、fective key differs t min Drilling/sawing resistance time T C Temperature of product for impact testing m g Drop mass for impact test BS EN 12320:2012EN 12320:2012 (E) 6 4 Requirements 4.1 General The structure of this clause reflects the classification as given in Clause 6. 4.2 Category of use (fir

29、st classification digit) Grade 1: according to requirements in 5.2 4.3 Durability (second classification digit) Grade 0: no requirements Grade 1: 10 000 cycles When tested in accordance with 5.3 it shall be possible to operate the padlock. The padlock fittings are excluded from the durability test.

30、4.4 Corrosion Resistance (third classification digit) Products shall be classified in accordance with EN 1670. Grade 0: no defined corrosion resistance Grade 1: 24h +1h/-0 h; Grade 2: 48h +1h/-0 h; Grade 3: 96h+1h/-0 h; Grade 4: 240h +1h/-0 h; Grade 5: 480h +1h/-0 h; After the corrosion test, the pa

31、dlock shall operate using a maximum torque on the key of 2.5 Nm. This corrosion test shall apply to the functionality only (not appearance). 4.5 Security (fourth classification digit) 4.5.1 General Some of the requirements can be confirmed with a certificate and test report according to EN 1303. In

32、grades 4, 5 and 6 it shall not be possible to remove the key until the shackle is deadlocked in the closed position and the key retained in open position. 4.5.2 Minimum number of effective key differs Padlocks shall have a minimum of n effective key differs (Table 2). For a mechanical padlock, the m

33、aximum number of steps on the same level shall be 60 %, maximum two adjacent and a minimum of three levels. BS EN 12320:2012EN 12320:2012 (E) 7 4.5.3 Non-interpassing of keys with just one interval effective differ When tested in accordance with 5.5.2, it shall not be possible to operate the padlock

34、 with keys differing from the correct key by one interval, i.e. the next closest key. The next closest key shall be defined by the manufacturer according to its key coding system. 4.5.4 Resistance to force on cylinder plug or locking mechanism When tested in accordance with 5.5.3, the cylinder plug

35、or the locking mechanism shall resist a force F1 (Table 2). 4.5.5 Resistance to torque on cylinder plug or locking mechanism When tested in accordance with 5.5.4, the cylinder plug or the locking mechanism shall resist a torque M2 (Table 2). 4.5.6 Resistance to pulling of shackle or staple When test

36、ed in accordance with 5.5.5, the shackle and the staple shall each resist a force F2 (Table 2). 4.5.7 Resistance to twisting of shackle or staple When tested in accordance with 5.5.6, the shackle and the staple shall each resist a torque M3 (Table 2). 4.5.8 Resistance to cutting of shackle or staple

37、 When tested in accordance with 5.5.7, the shackle and the staple shall each resist a force F3 (Table 2). 4.5.9 Resistance to impact on padlock body, shackle and staple at low temperature When tested in accordance with 5.5.8, the padlock body, the shackle and the staple cooled to temperature T, shal

38、l each resist the blows from the steel pole with the mass m and from the height h (Table 2). 4.5.10 Resistance to drilling of padlock body, shackle and staple When tested in accordance with 5.5.9, the padlock body, the shackle and the staple shall each resist drilling for a time t (Table 2). 4.5.11

39、Resistance to sawing of padlock body, shackle and staple When tested in accordance with 5.5.10, the padlock body, the shackle and the staple shall each resist sawing for a time t (Table 2). 4.5.12 Attack resistance When tested in accordance with 5.5.11, the padlock shall resist attacks with manual t

40、ools for a time t (see Table 2). BS EN 12320:2012EN 12320:2012 (E) 8 Table 2 Security requirements Require-ment clause number Requirement Test method clause number Test parameter Grade Unit 1 2 3 4 5 6 4.5.1 Key retained in open position yes / no - - - yes yes yes 4.5.2 Minimum number of effective k

41、ey differs 5.5.1 n 300 1 000 2 500 5 000 10 000 20 000 - 4.5.3 Non-interpassing of keys with just one interval differ - Torque on key 5.5.2 M1 1 1 1,5 1,5 1,5 1,5 Nm 4.5.4 Resistance to force on cylinder plug or locking mechanism 5.5.3 F1 - - 4 5 10 15 kN 4.5.5 Resistance to torque on cylinder plug

42、or locking mechanism 5.5.4 M2 - 2,5 5 15 20 30 Nm 4.5.6 Resistance to pulling of shackle and staple 5.5.5 F2 3 5 15 30 70 100 kN 4.5.7 Resistance to twisting of shackle and staple 5.5.6 M3 40 100 200 600 1 200 2 500 Nm 4.5.8 Resistance to cutting of shackle and staple 5.5.7 F3 6 15 25 45 70 100 kN 4

43、.5.9 Resistance to impact on padlock body, shackle and staple at low temperature 5.5.8 T m h - - - - - - - 20 1 250 800 - 20 3 050 1 000 - 40 6 550 1 400 - 40 7 150 1 500 C g mm 4.5.10 Resistance to drilling of padlock body, shackle and staple 5.5.9 t - - - 2 4 8 min 4.5.11 Resistance to sawing of p

44、adlock body, shackle and staple 5.5.10 t - - - 2 4 8 min 4.5.12 Manual attack 5.5.11 t toolsets - - - 3 5 10 min NOTE Classification is in six grades where grade 1 has the lowest requirement. 5 Test methods 5.1 General 5.1.1 Introduction The manufacturer will provide assembly and component drawings

45、to enable the tester to carry out a preliminary product assessment prior to testing. The padlock shall be tested in the locked position with the key removed. It is not necessary for the correct key to operate the padlock after testing. Padlocks/ padlock fittings and their original keys shall be take

46、n at random and submitted for each test. In the event of one of the original two samples failing the test, the padlocks/ padlock fittings shall be deemed to have failed and a further two shall be tested, both of which shall pass the test. BS EN 12320:2012EN 12320:2012 (E) 9 If the parts to be tested

47、 are inaccessible when the product is correctly mounted in accordance with the manufacturers instructions, the product shall be considered to have passed that test. A padlock shall be deemed to have been opened when a bar, of equal cross-section to that of its shackle, can be released. Ability to op

48、en can be checked at any time during the test by manipulation with a screwdriver or similar implement (maximum length 200 mm) for a period of 5 s max. 5.1.2 Tolerances Unless otherwise stated, the following tolerances shall apply : force 2 % ; torque 2 % ; mass/weight 2 % ; distance 2 % ; time 5 s ;

49、 temperature 2 C. Unless otherwise stated, the forces shall be applied progressively and without shock to the required load within 1 min. 5.1.3 Test environment The ambient temperature of the test environment shall be controlled throughout the test to 20 C 5 C unless otherwise stated. 5.1.4 Test tools Specification of steel for cutting and impact tests as required in 5.5.7.1 and 5.5.8. shall be structural steel E335 defined in EN 10025-2, heat treated to have a hardness of