EN 12561-3-2011 en Railway applications - Tank wagons - Part 3 Bottom filling and emptying devices for gases liquefied under pressure (Incorporating corrigendum November 2014)《铁路设施.pdf

1、BSI Standards PublicationBS EN 12561-3:2011Railway applications TankwagonsPart 3: Bottom filling and emptying devicesfor gases liquefied under pressureBS EN 12561-3:2011Incorporating corrigendum November 2014BS EN 12561-3:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implemen

2、tation of EN 12561-3:2011, incorporating corrigendum November 2014. It supersedes BS EN 12561-3:2002 which is withdrawn.The UK participation in its preparation was entrusted by Technical Committee RAE/3, Railway Applications - Rolling Stock Products, to Subcommittee RAE/3/-/9, Railway Applications -

3、 Wagons (Tank/Freight).A list of organizations represented on this subcommittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 20

4、14. Published by BSI Standards Limited 2014ISBN 978 0 580 88993 6ICS 13.300; 45.060.20Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2011.Amendments/cor

5、rigenda issued since publicationDate Text affected31 December 2014 Implementation of CEN corrigendum November 2014: Clause 8 deletedEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORM EN 12561-3 June 2011 ICS 13.300; 45.060.20 Supersedes EN 12561-3:2002English Version Railway applications - Tank wagons

6、- Part 3: Bottom filling andemptying devices for gases liquefied under pressure Applications ferroviaires - Wagons citernes - Partie 3:Dispositifs de remplissage et de vidange par le bas pourgaz liqufis sous pression Bahnanwendungen - Kesselwagen - Teil 3: UntenliegendeFll- und Entleereinrichtungen

7、fr unter Druck verflssigte Gase This European Standard was approved by CEN on 3 June 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date li

8、sts and bibliographical references concerning such nationalstandards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder

9、the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the samestatus as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,Finland, France, Germ

10、any, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNGM

11、anagement Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members. Ref. No. EN 12561-3:2011: EIncorporating corrig ndum ovember 14BS EN 12561-3:2011EN 12561-3:2011 (E) 2 Contents Page Foreword 31 Scope 42 N

12、ormative references 43 Terms and definitions .44 Requirements .44.1 General 44.2 Constituent parts .44.3 Locks and seals .54.4 Dimensions .55 Arrangement and structure 65.1 Fittings for the liquid phase 65.2 Fittings for the vapour phase .75.3 Quick closing bottom valve system.75.4 External valves a

13、nd connection fittings 85.5 External branch pipes .85.6 Earthing devices 86 Reserved spaces for connection devices .96.1 General arrangement .96.2 Relative positioning of connection devices . 107 Threaded couplings 108 Dry disconnect couplings 10Annex A (informative) Threaded couplings . 11A.1 Gener

14、al arrangement 11A.2 Dimensions and tolerances . 11A.3 Tests and marking 12Bibliography . 13Figures Figure 1 Plate identifying the vapour phase branch pipe 5Figure 2 Example of arrangement for the liquid phase 6Figure 3 Example of arrangement for the vapour phase .7Figure 4 Arrangement of the contro

15、l cable at buffer height 1 060 mm.8Figure 5 Reserved spaces for connection devices 9Figure 6 Relative positioning of connection devices 10Figure A.1 Threaded couplings . 11Figure A.2 Section Z 11Figure A.3 Plug of threaded coupling . 12Tables Table A.1 Dimensions of couplings12 Text deletedBS EN 125

16、61-3:2011EN 12561-3:2011 (E) 3 Foreword This document (EN 12561-3:2011) has been prepared by Technical Committee CEN/TC 256 Railway applications, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical te

17、xt or by endorsement, at the latest by December 2011, and conflicting national standards shall be withdrawn at the latest by December 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held respo

18、nsible for identifying any or all such patent rights. This document supersedes EN 12561-3:2002. This European Standard Railway applications Tank wagons consists of the following parts: Part 1: Identification plates for tank wagons for the carriage of dangerous goods; Part 2: Bottom emptying devices

19、for liquid products including vapour return; Part 3: Bottom filling and emptying devices for gases liquefied under pressure; Part 4: Devices for top filling and emptying of liquid products; Part 5: Devices for vapour return while filling or emptying of liquid products; Part 6: Manholes; Part 7: Plat

20、forms and ladders; Part 8: Heating connections. The changes made during this revision are editorial because of the change of the title of part 1 and the necessary updates of references. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries

21、 are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,

22、 Spain, Sweden, Switzerland and the United Kingdom BS EN 12561-3:2011EN 12561-3:2011 (E) 4 1 Scope This European Standard specifies requirements on and characteristics of bottom filling and emptying devices on tank wagons used for the carriage of gases liquefied under pressure having a test pressure

23、 up to 2,9 MPa. This European Standard specifies the important dimensions and arrangements for the filling and emptying connections. Safety functions of these devices are subject to RID requirements and not described in this document. This European Standard applies to new tank wagons built after the

24、 1st January 2010. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1456

25、4,Tanks for transport of dangerous goods Terminology EN ISO 286-1, Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits (ISO 286-1) ISO 3419, Non-alloy and alloy steel butt-welding fittings ISO 4200:1991, Plain end s

26、teel tubes, welded and seamless General tables of dimensions and masses per unit length ISO 7005-1:1992, Metallic flanges Part 1: Steel flanges 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 14564 and the following apply. 3.1 stop valve part of the i

27、nternal bottom valve comprising the disc, the gasket, the spring and the seat 4 Requirements 4.1 General The liquid and vapour phase system shall consist of DN 80 pipes and valves. The external connection interface shall be: DN 80 diameter for the liquid phase, and DN 50 diameter for the vapour phas

28、e. 4.2 Constituent parts Both phases shall be equipped with: BS EN 12561-3:2011EN 12561-3:2011 (E) 5 a) an internal quick closing bottom valve according to 5.3, b) an external branch pipe according to 5.5, c) at each end of the branch pipe a flanged external valve according to 5.4 fitted e.g. with t

29、hreaded coupling according to Annex A. The vapour phase branch pipe shall be identified by the letters “GAS“ of 30 mm height embossed on a metallic plate as shown in Figure 1 which is permanently fixed on both sides of the tank wagon. Figure 1 Plate identifying the vapour phase branch pipe 4.3 Locks

30、 and seals External valves as well as internal bottom valves shall be capable of being secured in their closed position to prevent any unintentional opening through impact or an inadvertent act. The operating controls of the external valves shall be equipped with devices to which a seal can be prope

31、rly attached. For customs seals, a hole of diameter 15 mm shall be required. 4.4 Dimensions They are given in millimetres. Unless otherwise indicated in this European Standard the tolerances of EN ISO 286-1 apply. BS EN 12561-3:2011EN 12561-3:2011 (E) 6 5 Arrangement and structure 5.1 Fittings for t

32、he liquid phase The fittings for the liquid phase shall be as shown in Figure 2. Key 1 internal quick closing bottom valve DN 80 2 external valve DN 80 3 threaded coupling DN 80 4 branch pipe DN 80 Figure 2 Example of arrangement for the liquid phase BS EN 12561-3:2011EN 12561-3:2011 (E) 7 5.2 Fitti

33、ngs for the vapour phase The vapour phase shall include a pressure compensation line located inside the tank. The fittings for the vapour phase shall be as shown in Figure 3. Key 1 internal quick closing bottom valve DN 80 2 external valve DN 80 3 threaded coupling DN 50 4 branch pipe DN 80 5 pressu

34、re compensation line DN 80 Figure 3 Example of arrangement for the vapour phase 5.3 Quick closing bottom valve system In addition to the requirements in RID, the quick closing bottom valve system needs to meet the following requirements: a) The quick closing bottom valve shall be equipped with an in

35、stant operation safety device which closes the valve automatically in the event of an unintended movement of the tank wagon or a fire. This shall be achieved by means of a control cable as shown in Figure 4 which connected to an external rail hook. The guide tube and attachment ring for the control

36、cable shall for a buffer height of 1 060 mm be arranged and dimensioned as shown in Figure 4 below. The inner diameter of the attachment ring shall be 50 mm. When the bottom valve is closed, the control cable including the ring shall remain in gauge. b) Have the operating controls positioned at a su

37、fficient distance from the outlet pipes to permit easy access for operation. BS EN 12561-3:2011EN 12561-3:2011 (E) 8 Dimensions in millimetres Key 1 control cable 2 guide tube 3 distance for internal security device with quick closing when being in open position 4 top of rail 5 ring used to attach c

38、ontrol cable Figure 4 Arrangement of the control cable at buffer height 1 060 mm 5.4 External valves and connection fittings The external flange of the external valves shall comply with face type E or type C PN 40 of ISO 7005-1:1992. The setting whether open or closed and/or the direction of closure

39、 of the external valves shall be capable of being visually verified. 5.5 External branch pipes The external branch pipes shall be horizontal in order to minimise product residue in the pipe following loading and unloading. NOTE The external branch pipes may be built with seamless line pipes and butt

40、 welding fittings (straight tees, long radius elbows, etc.) made from low temperature steel as specified in ISO 9329-3. If welded pipes are used they shall exhibit a suitable degree of safety comparable to that of the shell itself. Dimensions of line pipes shall be as specified by serial 1 Grade G s

41、pecified in ISO 4200:1991. Dimensions of butt weld fittings shall be as specified in ISO 3419. 5.6 Earthing devices Two stainless steel earthing plates shall be welded on each side of the tank wagon. Their dimensions shall be at least 40 mm 80 mm 5 mm. They shall be positioned as shown in Figure 6.

42、BS EN 12561-3:2011EN 12561-3:2011 (E) 9 6 Reserved spaces for connection devices 6.1 General arrangement The connecting faces of liquid and vapour phases shall be positioned entirely within the dimensions shown in Figure 5. Dimensions in millimetres 1) These dimensions are given for tank wagons in t

43、he new and empty conditions. 2) For special insulated wagons, a maximum 1 500 is allowed. 3) For traffic of continental tank wagons running in Great Britain, the kinematic gauge for Great Britain rules defined in the Technical Specification for Interoperability for freight wagons (TSI 9) also apply.

44、 Figure 5 Reserved spaces for connection devices BS EN 12561-3:2011EN 12561-3:2011 (E) 10 6.2 Relative positioning of connection devices The connecting faces of filling and emptying devices for liquid and vapour phases shall be located in vertical planes distant at maximum of 50 mm. These vertical p

45、lanes shall be parallel to the longitudinal symmetry plane of the tank wagon. The distance between the centres of the two connecting faces shall be as shown in Figure 6. Dimensions in millimetres Key 1 liquid line 2 earthing plates 3 connection faces 4 gas line Figure 6 Relative positioning of conne

46、ction devices 7 Threaded couplings The general arrangement of threaded couplings is described in Annex A. 8 Dry disconnect couplings The general arrangement of dry disconnect couplings is described in Annex B. Text deletedBS EN 12561-3:2011EN 12561-3:2011 (E) 11 Annex A (informative) Threaded coupli

47、ngs A.1 General arrangement The general arrangement of threaded couplings shall be as shown in Figure A.1. Coupling for vapour line DN 80/5 Coupling for liquid line DN 80 NOTE For section Z see Figure A.2. Figure A.1 Threaded couplings A.2 Dimensions and tolerances The dimensions of threaded couplin

48、gs shall be as shown in Figure A.2 and Figure A.3 and given in Table A.1. The dimensions of the gaskets shall take into account the characteristics of the gasket material in order to ensure the tightness, the interchange ability and the good functioning of the threaded coupling. Figure A.2 Section Z

49、 BS EN 12561-3:2011EN 12561-3:2011 (E) 12 Dimensions in millimetres Holes for tightening and loosening the coupling by means of a key Figure A.3 Plug of threaded coupling Table A.1 Dimensions of couplings Dimensions in millimetres DN b10,2 b2+0,25 -0 d1d2 a d4d5+0 -0,3 d6d7d8d9l1max l2r 0,2 50 11,5 4 218 96,6 52,5 68,3 68 88 78 72 267 39,3 52 80 11,5 4 218 136,3 78 101,6 101 121 108 105 175 55,9 75 aTh