EN 12561-4-2011 en Railway applications - Tank wagons - Part 4 Devices for top filling and emptying of liquid products《铁路设施 油罐车 第4部分 液态产品用顶部装卸装置》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 12561-4:2011Railway applications TankwagonsPart 4: Devices for top filling and emptyingof liquid productsBS EN 12561-4:2011 BRITISH STANDARDNational forewordThis British St

2、andard is the UK implementation of EN 12561-4:2011.It supersedes BS EN 12561-4:2002 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee RAE/1/-/9, Railway Applications - Wagons (Tank/Freight).A list of organizations represented on this committee can beobtai

3、ned on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 72810 5ICS 13.300; 45.060.20Compliance with a British Standard cannot confer immunity fromlegal obligations

4、.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2011.Amendments issued since publicationDate Text affectedBS EN 12561-4:2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12561-4 June 2011 ICS 13.300; 45.060.20 Supersedes EN 125

5、61-4:2002English Version Railway applications - Tank wagons - Part 4: Devices for top filling and emptying of liquid products Applications ferroviaires - Wagons citernes - Partie 4: Dispositifs suprieurs de vidange et de remplissage par le haut pour produits liquides Bahnanwendungen - Kesselwagen -

6、Teil 4: Einrichtungen fr Obenentleerung und Obenbefllung von flssigen Stoffen This European Standard was approved by CEN on 3 June 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national

7、 standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version

8、 in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czec

9、h Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EURO

10、PEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12561-4:2011: EBS EN 12561-4:2011EN 12561-4:2011 (E) 2 Contents Page Fore

11、word 3Introduction .41 Scope 52 Normative references 53 Terms and definitions .54 Requirements .54.1 General 54.2 Dimensions .54.3 Filling and emptying devices 64.4 Manhole 85 Positioning of equipment 8Bibliography . 10Figures Figure 1 Examples of handle on blind flange 7Figure 2 Splash ring .7Figur

12、e 3 Arrangement of equipment 9Table Table 1 Internal diameter of splash rings 8BS EN 12561-4:2011EN 12561-4:2011 (E) 3 Foreword This document (EN 12561-4:2011) has been prepared by Technical Committee CEN/TC 256 “Railway applications”, the secretariat of which is held by DIN. This European Standard

13、shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2011, and conflicting national standards shall be withdrawn at the latest by December 2011. Attention is drawn to the possibility that some of the elements of thi

14、s document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12561-4:2002. This European Standard Railway applications Tank wagons consists of the following parts: Part 1: Identification pl

15、ates for tank wagons for the carriage of dangerous goods; Part 2: Bottom emptying devices for liquid products including vapour return; Part 3: Bottom filling and emptying devices for gases liquefied under pressure; Part 4: Devices for top filling and emptying of liquid products; Part 5: Devices for

16、vapour return while filling or emptying of liquid products; Part 6: Manholes; Part 7: Platforms and ladders; Part 8: Heating connections. The changes made during this revision are editorial because of the change of the title of part 1 and the necessary updates of references. According to the CEN/CEN

17、ELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuan

18、ia, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 12561-4:2011EN 12561-4:2011 (E) 4 Introduction Tank wagons for the transport of liquid substances are equipped with top devices standardised within CEN

19、Technical Committee 256 Railway Applications. Devices fitted to tank wagons that can be emptied through the top, and which incorporate a dip pipe, are covered by this European Standard. Devices fitted on the top of tank wagons that can only be bottom emptied are covered by EN 12561-5. BS EN 12561-4:

20、2011EN 12561-4:2011 (E) 5 1 Scope This European Standard is applicable to top devices of tank wagons used for liquid substances of RID carried in the liquid state and able to be top filled and emptied. Safety functions of these devices are subject to RID requirements and not described in this docume

21、nt. This European Standard specifies the type of equipment which is fitted on the top of such tank wagons and the important dimensions for their connections. This European Standard applies to new tank wagons built after the 1st January 2010. 2 Normative references The following referenced documents

22、are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12561-2, Railway applications Tank wagons Part 2: Bottom emptying devices for liq

23、uid products including vapour return EN 12561-6, Railway applications Tank wagons Part 6: Manholes EN ISO 286-1, Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits (ISO 286-1:2010) ISO 7005-1:1992, Metallic flanges

24、 Part 1: Steel flanges 3 Terms and definitions Not applicable. 4 Requirements 4.1 General In order to allow the filling and emptying of tank wagons through the top, the tank wagon shall be fitted with devices for loading and emptying and with a manhole. Where bottom emptying devices, return vapour d

25、evice and associated auto vent valves are also fitted they shall be in compliance with EN 12561-2. All openings shall be equipped with devices to which a seal can be properly attached. For customs seals, a hole of diameter 15 mm shall be required. All nozzles including manhole shall be positioned ac

26、cording to Clause 5. 4.2 Dimensions All dimensions are given in millimetres. Unless otherwise indicated in this European Standard tolerances of EN ISO 286-1 apply. BS EN 12561-4:2011EN 12561-4:2011 (E) 6 4.3 Filling and emptying devices These devices shall allow the filling of tank wagons through th

27、e filling inlet or the dip pipe and the emptying through the dip pipe. They shall consist of the following minimum equipment: a dip pipe DN 80 on nozzle DN 150; an air/vapour connection DN 50 to DN 80; a filling or spare nozzle, DN 150 to DN 300. Flanges shall have their connection dimensions in acc

28、ordance with ISO 7005-1:1992 PN 10 series, face A or face B. Blind flanges shall be fitted with a handle mounted horizontally or vertically according to Figure 1 below. NOTE Other dimension for the nozzles are permissible by special agreement between supplier and customer. BS EN 12561-4:2011EN 12561

29、-4:2011 (E) 7 Dimensions in millimetres Key 1 hole for custom seal 2 horizontal arrangement 3 vertical arrangement Figure 1 Examples of handle on blind flange Where blind flanges which are not preceded by a valve are fitted on filling or emptying devices, the blind flanges shall be equipped with spl

30、ash rings according to Figure 2 and Table 1. Dimensions in millimetres Figure 2 Splash ring BS EN 12561-4:2011EN 12561-4:2011 (E) 8 Table 1 Internal diameter of splash rings Flanges d mm DN 50 170 DN 80 205 DN 150 285 DN 300 455 In addition to the markings specified by ISO 7005-1, blind flanges shal

31、l be identified by painting them red for dip pipe and blue for air/vapour connection. NOTE It is recommended to have a sufficient space at the top of the flanges to install valves and/or couplings. The distance between air/vapour connection and dip pipe centres shall be in accordance with Figure 3.

32、4.4 Manhole The tank wagons shall be fitted with a manhole according to EN 12561-6 located at the top centre line of the tank and in the proximity of middle of the tank. Where the tank wagon is fitted with an internal bottom valve, the manhole shall be located so that its vertical projection on the

33、bottom of the tank is not closer than 100 mm from any part of that valve. 5 Positioning of equipment The equipment shall be positioned in the area as indicated in Figure 3. BS EN 12561-4:2011EN 12561-4:2011 (E) 9 Dimensions in millimetres Key 1 filling inlet 2 air inlet 3 dip pipe nozzle 4 dip pipe

34、5 manhole 6 transversal tank axis 7 longitudinal tank axis 8 air inlet area 9 area for positioning of equipment Figure 3 Arrangement of equipment BS EN 12561-4:2011EN 12561-4:2011 (E) 10 Bibliography 1 EN 12561-5, Railway applications - Tank wagons - Part 5: Devices for vapour return while filling o

35、r emptying of liquid products 2 EN 12972, Tanks for transport of dangerous goods Testing, inspection and marking of metallic tanks 3 RID, Regulations concerning the International Carriage of Dangerous Goods by Rail1)implementing Commission Directives 2003/28/EC and 2003/29/EC. 4 UIC 573, Technical c

36、onditions for the construction of tank wagons2)1) Commonly known as RID. 2) May be purchased from: Railway Technical Publications (ETF), 16 rue Jean Rey, F-75015 Paris. This page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standard

37、s-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)2

38、0 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding a

39、n inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS wh

40、ich ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, in

41、ternational and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, u

42、nless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive de

43、tails on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-mi

44、nistration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright

45、,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise w

46、ithout prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: