EN 12629-1-2000 en Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 1 Common requirements (Incorporates Amendment A1 2010).pdf

1、|BRITISH STANDARDBS EN12629-1:200ICS 91.220NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWMachines for themanufacture ofconstructional productsfrom concrete andcalcium-silicate Safety Part 1: Common requirements+A1:20100National forewordThis British Standard is the UK implemen

2、tation of EN 12629-1:2000+A1:2010. It supersedes BS EN 12629-1:2001 which is withdrawn.The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendme

3、nt A1 is indicated by !“.The UK participation in its preparation was entrusted to Technical Committee MCE/3, Safeguarding of machinery, to Subcommittee MCE/3/7, Machines for pre-cast concrete and calcium-silicate products Safety.A list of organizations represented on this subcommittee can be obtaine

4、d on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.BS EN 12629-1:2000+A1:2010This British Standard, h

5、aving been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 February 2001 BSI 2010Amendments/corrigenda issued since publicationDate Comments 31 October 2010 Implementation of CEN amendent A1:20

6、10, alignment of BSI and CEN publication datesISBN 978 0 580 63121 4EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12629-1:2000+A1 September 2010 ICS 91.220 Supersedes EN 12629-1:2000English Version Machines for the manufacture of constructional products from concrete and calcium-silicate - Sa

7、fety - Part 1: Common requirements Machines pour la fabrication de produits de construction en bton et silico-calcaire - Scurit - Partie 1: Exigences communes Maschinen fr die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 1: Gemeinsame Anforderungen This European

8、 Standard was approved by CEN on 12 May 2000 and includes Amendment 1 approved by CEN on 5 August 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

9、 Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translatio

10、n under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Ge

11、rmany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMU

12、NG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12629-1:2000+A1:2010: EEN 12629-1:2000+A1:2010 (E) 2 Contents Foreword 4Introduction . 51 Scope 52 Normative references 53

13、 !Terms and definitions“ . 74 List of significant hazards 94.1 Mechanical hazards . 94.2 Electrical hazards 94.3 Hazards generated by noise . 94.4 Hazards generated by materials and products . 94.5 Hazards generated by neglecting ergonomic principles . 94.6 Hazards caused by failure of energy supply

14、 95 !Safety requirements and/or protective measures“ . 95.1 Mobile parts of power transmission 105.2 Mobile parts taking part in the working process 105.3 Tool-setting changing of tools and machine maintenance operations . 125.4 Safety functions treatment by control networks 135.5 Warning equipment

15、. 135.6 Electrical equipment 135.7 Noise . 135.8 Materials and products . 145.9 Ergonomic design 145.10 Hydraulic and pneumatic equipment . 145.11 Integrated transport systems that are an integral part of the machine . 145.12 !Additional requirements for mobile manufacturing machines“ 146 Verificati

16、on of safety measures and/or provisions 167 Information for use 177.1 Safety systems . 177.2 Interface 187.3 Spare parts . 187.4 Noise . 187.5 Access 187.6 Storage 187.7 Oils 188 Marking . 19BS EN 12629-1:2000+A1:2010EN 12629-1:2000+A1:2010 (E) 3 Annex A (informative) Examples of machines for the ma

17、nufacture of constructional products from concrete and calcium silicate . 20Annex B (informative) Guarding examples . 22Annex ZA (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC“ . 27!Bibliography“ . 28BS EN 12629-1:2000+A1:2010EN 1

18、2629-1:2000+A1:2010 (E) 4 Foreword This document (EN 12629-1:2000+A1:2010) has been prepared by Technical Committee CEN/TC 151 “Construction equipment and building material machines Safety”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national stand

19、ard, either by publication of an identical text or by endorsement, at the latest by March 2011, and conflicting national standards shall be withdrawn at the latest by March 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN

20、 and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document includes Amendment 1, approved by CEN on 2010-08-05. This document supersedes EN 12629-1:2000. The start and finish of text introduced or altered by amendment is indicated in the text by tags !

21、 “. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this sta

22、ndard. !The series “Machines for the manufacture of constructional products from concrete and calcium silicate Safety“ consists of the following parts: Part 1: Common requirements Part 2: Block making machines Part 3: Slide and turntable machines Part 4: Concrete roof tile making machines Part 5.1:

23、Pipe making machines manufacturing in the vertical axis Part 5.2: Pipe making machines manufacturing in the horizontal axis Part 5.3: Pipe prestressing machines Part 5.4: Concrete pipe coating machines Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products Part 7:

24、 Stationary and mobile equipment for long line manufacture of prestressed products Part 8: Machines and equipment for the manufacture of constructional products from calcium silicate (and concrete)“ !deleted text“ According to the CEN/CENELEC Internal Regulations, the national standards organization

25、s of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,

26、Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 12629-1:2000+A1:2010EN 12629-1:2000+A1:2010 (E) 5 Introduction This European Standard is a Type C-standard as stated in !EN ISO 12100“. The machinery concerned and the extent to which hazards, hazardous situations and

27、events are covered are indicated in the scope of this standard. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been d

28、esigned and built according to the provisions of this type C standard. Reference to pertinent standards mentioned above is made where requirements of such standards are relevant. 1 Scope 1.1 This European Standard applies to machines for the manufacture of constructional products from concrete and/o

29、r calcium silicate examples of which are listed in annex A of this part. It gives concepts and general and common requirements for the design, operation and maintenance of such machines. 1.2 !This European Standard deals with hazards listed in Clause 4 which can arise during the operation and mainte

30、nance, including the interfaces, of the machines for the manufacture of constructional products from concrete and calcium silicate, when carried out as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer. Part 2 to 8 of this standard give additional specific

31、requirements and therefore have to be applied together with this part.“ 1.3 The preparation of concrete and/or calcium-silicate mixture and the transport from the mixer to the manufacturing plant are not part of this European Standard (see !EN 12151:2007“). The equipment for the transport and handli

32、ng of formed products, other than the integrated transport system, is not covered by this standard. !deleted text“ !1.4“ At the time of drafting, machine specific noise test codes for !EN 12629-2 to -8“ are not available to fulfill the requirements of 5.7.2 and 7.4.2. When they are available, they w

33、ill be incorporated in these standards. !1.5 This document is not applicable to machines for the manufacture of constructional products from concrete and/or calcium silicate, which are manufactured before the date of publication of this document by CEN.“ 2 Normative references !The following referen

34、ced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 349:1993+A1:2008, Safety of machinery Minimum gaps to avoid crushin

35、g of parts of the human body EN 457:1992, Safety of machinery Auditory danger signals General requirements, design and testing EN 547-1:1996+A1:2008, Safety of machinery Human body measurements Part 1: Principles for determining the dimensions required for openings for whole body access into machine

36、ry EN 547-2+A1:2008, Safety of machinery Human body measurements Part 2: Principles for determining the dimensions required for access openings EN 547-3:1996+A1:2008, Safety of machinery Human body measurements Part 3: Anthropometric data BS EN 12629-1:2000+A1:2010EN 12629-1:2000+A1:2010 (E) 6 EN 57

37、4, Safety of machinery Two hand control devices Functional aspects Principles for design EN 614-1:2006+A1:2009, Safety of machinery Ergonomic design principles Part 1: Terminology and general principles EN 626-1:1994+A1:2008, Safety of machinery Reduction of risks to health from hazardous substances

38、 emitted by machinery Part 1: Principles and specifications for machinery manufacturers EN 894-1, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 1: General principles for human interactions with displays and control actuators EN 894-2, Safety of mac

39、hinery Ergonomics requirements for the design of displays and control actuators Part 2: Displays EN 894-3, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 3: Control actuators EN 953:1997+A1:2009, Safety of machinery Guards General requirements for t

40、he design and construction of fixed and movable guards EN 954-1:1996, Safety of machinery Safety-related parts of control systems Part 1: General principles for design EN 982:1996+A1:2008, Safety of machinery Safety requirements for fluid power systems and their components Hydraulics EN 983:1996+A1:

41、2008, Safety of machinery Safety requirements for fluid power systems and their components Pneumatics EN 999, Safety of machinery The positioning of protective equipment in respect of approach speeds of parts of the human body EN 1037:1995+A1:2008, Safety of machinery Prevention of unexpected start-

42、up EN 1088, Safety of machinery Interlocking devices associated with guards Principles for design and selection EN ISO 3746:2009, Acoustics Determination of sound power levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane (ISO 374

43、6:1995, including Cor 1:1995) EN ISO 11204:2010, Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010) EN ISO 11688-1:2009, Acoustics Recommend

44、ed practice for the design of low-noise machinery and equipment Part 1: Planning (ISO /TR 11688-1:1995) EN ISO 12100-1:2003, Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery Basic conc

45、epts, general principles for design Part 2: Technical principles (ISO 12100-2:2003) EN ISO 13850:2008, Safety of machinery Emergency stop Principles for design (ISO 13850:2006) EN ISO 13857:2008, Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO

46、 13857:2008) EN ISO 14122-1:2001, Safety of machinery Permanent means of access to machinery Part 1: Choice of fixed means of access between two levels (ISO 14122-1:2001) BS EN 12629-1:2000+A1:2010EN 12629-1:2000+A1:2010 (E) 7 EN ISO 14122-2:2001, Safety of machinery Permanent means of access to mac

47、hinery Part 2: Working platforms and walkways (ISO 14122-2:2001) EN ISO 14122-3:2001, Safety of machinery Permanent means of access to machinery Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2001) EN ISO 14122-4:2004, Safety of machinery Permanent means of access to machinery Part 4: Fixe

48、d ladders (ISO 14122-4:2004) EN 60204-1:2006, Safety of machinery Electrical equipment of machines Part 1: General requirements (IEC 60204-1:2005, modified) EN 61310-1:2008, Safety of machinery Indication, marking and actuation Part 1: Requirements for visual, acoustic and tactile signals (IEC 61310-1:2007) EN 61496-1:2004, Safety of machinery Electro-sensitive protective equipment Part 1: General requirements and tests (IEC 61496-1:2004, modified)“ 3 !Terms and definitions“ !F