EN 12629-4-2001 en Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 4 Concrete roof tile making machines (Incorporates Ame.pdf

1、BRITISH STANDARDBS EN 12629-4:2001Machines for the manufacture of constructional products from concrete and calcium-silicate Safety Part 4: Concrete tile making machinesICS 91.220NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW+A1:2010roof National forewordThis British Standard

2、 is the UK implementation of EN 12629-4:2001+A1:2010. It supersedes BS EN 12629-4:2001 which is withdrawn.The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text alt

3、ered by CEN amendment A1 is indicated by !“.The UK participation in its preparation was entrusted by Technical Committee MCE/3, Safeguarding of machinery, to Subcommittee MCE/3/7, Machines for pre-cast concrete and calcium-silicate products Safety.A list of organizations represented on this subcommi

4、ttee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.BS EN 12629-4:2001+A1:2010This

5、British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 April 2001 BSI 2010Amendments/corrigenda issued since publicationDate Comments 31 October 2010 Implementation of CE

6、N amendment A1:2010ISBN 978 0 580 63124 5EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12629-4:2001+A1 September 2010 ICS 91.220 Supersedes EN 12629-4:2001English Version Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 4: Concrete roo

7、f tile making machines Machines pour la fabrication de produits de construction en bton et silico-calcaire - Scurit - Partie 4: Machines pour la fabrication de tuiles en bton Maschinen fr die Herstellung von Bauprodukten aus Betonund Kalksandsteinmassen - Sicherheit - Teil 4: Beton-Dachsteinmaschine

8、n This European Standard was approved by CEN on 1 January 2001 and includes Amendment 1 approved by CEN on 5 August 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard witho

9、ut any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language

10、made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, F

11、inland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHE

12、S KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12629-4:2001+A1:2010: EEN 12629-4:2001+A1:2010 (E) 2 Contents Foreword 3Introduction . 41 Scope . 42 Nor

13、mative references . 53 !Terms and definitions“ . 54 List of significant hazards . 64.1 Mechanical Hazards . 64.1.1 Crushing hazards . 64.1.2 Shearing hazards 64.1.3 Cutting and severing hazards . 64.1.4 Entanglement hazards . 64.1.5 Drawing - In or trapping hazards 74.1.6 Impact hazards 74.1.7 High

14、pressure fluid ejection 74.1.8 Ejection of parts or materials 74.1.9 Slip, trip and fall hazards . 74.2 Noise Hazards . 74.3 Hazards from materials used 74.3.1 Contact or inhalation 74.3.2 Fire or explosion . 74.4 Hazards generated by neglecting ergonomic principles in design. 74.4.1 Neglected use o

15、f personal protective equipment . 74.4.2 Inadequate local lighting . 74.4.3 Human error 75 !Safety requirements and/or protective measures“ 85.1 General 85.2 Mechanical hazards 85.2.1 Propulsion unit and cutting unit and extrusion unit . 85.2.2 Press unit and its interfaces 85.2.3 Slip, trip and fal

16、l hazards . 85.2.4 Contact 85.2.5 Control panel . 86 !Verification of safety requirements and/or protective measures“ . 87 !Information for use“ 98 Warnings . 99 Marking 9Annex A (informative) First typical concrete tile manufacturing plant 10Annex B (informative) Second typical concrete tile manufa

17、cturing plant . 11Annex ZA (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC“ 12Bibliography 13BS EN 12629-4:2001+A1:2010EN 12629-4:2001+A1:2010 (E) 3 Foreword This document (EN 12629-4:2001+A1:2010) has been prepared by Technical Co

18、mmittee CEN/TC 151 “Construction equipment and building material machines - Safety “, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2011, and confl

19、icting national standards shall be withdrawn at the latest by March 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This documen

20、t includes Amendment 1, approved by CEN on 2010-08-05. This document supersedes EN 12629-4:2001. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! “. This European Standard has been prepared under a mandate given to CEN by the European Commission and

21、the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. !deleted text“ !The series “Machines for the manufacture of constructional products from concrete

22、and calcium silicate Safety“ consists of following parts: Part 1: Common requirements Part 2: Block making machines Part 3: Slide and turntable machines Part 4: Concrete rooftile making machines Part 5.1: Concrete pipe machines manufacturing in the vertical axis Part 5.2: Concrete pipe machines manu

23、facturing in the horizontal axis Part 5.3: Pipe prestressing machines Part 5.4: Concrete pipe coating machines Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products Part 7: Stationary and mobile equipment for the benched manufacture of prestressed products Part 8

24、: Machines and equipment for the manufacture of constructional products from calcium silicate (and concrete).“ According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

25、 Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 12629-4:2001+A1:2010E

26、N 12629-4:2001+A1:2010 (E) 4 Introduction !This European Standard is a Type C-standard as stated in EN ISO 12100. The machinery concerned and the extent to which hazards, hazardous situation and events are covered are indicated in the scope of this document. When provisions of this type C document a

27、re different from those, which are stated in type A or B documents, the provisions of this type C document take precedence over the provisions of the other documents, for machines that have been designed and built according to the provisions of this type C document. This document specifies the addit

28、ional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific for the concrete roof tile making machines as described in 1.1. With the aim of clarifying the intentions of the document it should be noticed that the following assumptions were made when producing it: specific condit

29、ions of use or environmental conditions out of the scope of the document shall be the subject of negotiations between the manufacturer and the user/owner, the equipment will only be used by competent and designated persons, the place of use/installation is adequately lit, all operations are carried

30、out by specially trained operators.“ 1 Scope ! 1.1 This part of EN 12629, taken together with EN 12629-1:2000+A1:2010, applies to concrete roof tile making machines. EN 12629-1:2000+A1:2010 specifies general requirements applicable to machines for the manufacture of constructional products from conc

31、rete and calciumsilicate. This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific to the machines it covers.“ 1.2 Limits of the machine The tile making machine is considered to begin at the point where moulds and/or the concrete are delivere

32、d to the fixed part of the machine and ends after the tile cutting process where products on their moulds are delivered on to an outfeed conveyor (see Annexes A and B). Moulds and concrete may be delivered to and removed from the machine by hand. The preparation of the concrete mixture and the trans

33、port from the mixer to the machine are not covered by this standard. The equipment for the transport and handling of formed products is not covered by this standard. BS EN 12629-4:2001+A1:2010EN 12629-4:2001+A1:2010 (E) 5 ! 1.3 This European Standard deals with all significant hazards pertinent to t

34、hese machines, including the interfaces, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant ha

35、zards. This standard establishes safety requirements and/or methods of protection which applies to these machines.“ ! 1.4 This document is not applicable to concrete roof tile making machines, which are manufactured before the date of publication of this document by CEN.“ 2 Normative references !The

36、 following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 953, Safety of machinery Guards General requireme

37、nts for the design and construction of fixed and movable guards EN 1837, Safety of machinery Integral lighting of machines EN 12629-1:2000+A1:2010, Machines for the manufacture of constructional products from concrete and calcium-silicate Safety Part 1: Common requirements EN ISO 12100-1:2003, Safet

38、y of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles (ISO 12100-2:2003) EN ISO 13850, Safety of machinery Emergency st

39、op Principles for design (ISO 13850:2006)“ 3 !Terms and definitions“ !For the purposes of this document, the terms and definitions given in EN ISO 12100-1:2003, EN 12629-1:2000+A1:2010 and the following apply.“ 3.1 concrete roof tile making machine tile machine Power driven automatic machine which m

40、anufactures concrete roof tiles and is part of a complex manufacturing process (see annexes A and B) NOTE The tile manufacturing process is complex comprising stationary and mobile equipment, designed to manufacture roof tiles in various sizes and shapes, including the complementary roof fitting. Th

41、e tile machine is only one element in the overall tile making process which may comprise a number of linked equipment (see annexes A and B). 3.2 machine parts 3.2.1 extrusion unit Equipment consisting of a propulsion unit which drives the mould through to the making section of the file machine, forc

42、ing the mixed raw materials and mould a die. The extruded column is cut to length BS EN 12629-4:2001+A1:2010EN 12629-4:2001+A1:2010 (E) 6 3.2.2 press unit equipment, including hopper(s) and internal conveying system, for the production of tile by moulding and compaction of mortar (concrete) with or

43、without vibration which then ejects the mould and formed tile 3.2.3 propulsion unit mechanism for supporting and/or driving the mould through the making section 3.2.4 sample point A position at the machine outlet from which a representative sample of product may be removed from the process 3.2.5 kni

44、fe gear A cutting mechanism for the extruded concrete ribbon to allow it to be cut to the required dimensions 4 List of significant hazards This clause contains all hazards and hazardous situations, as far as they are dealt with in this European Standard, identified by risk assessment as specific fo

45、r this type of machinery and which require action to eliminate or reduce risk. !In accordance with Clause 4 of EN 12629-1:2000+A1:2010 the hazard zones described in the following sub-clauses are illustrated in Annexes A and B.“ 4.1 Mechanical Hazards 4.1.1 Crushing hazards Access to the propulsion u

46、nit. Access to press enclosure. Access to trap between mould and damping mechanisms. 4.1.2 Shearing hazards Access between the fixed and moving parts of the propulsion unit and associated drive systems. From the mould on entry to the press enclosure. Between the fixed and moving parts of the press.

47、4.1.3 Cutting and severing hazards Access to the knife gear and any trimming blades. Sharp machinery parts. 4.1.4 Entanglement hazards From the propulsion and cutting unit projections. From access to moving parts in the making section. BS EN 12629-4:2001+A1:2010EN 12629-4:2001+A1:2010 (E) 7 4.1.5 Dr

48、awing - In or trapping hazards From the extrusion unit. From access to nips on concrete recovery conveyors and in and outfeed conveyors. From access to moving parts in the making section. 4.1.6 Impact hazards Access to projections on moving propulsion and cutting units. 4.1.7 High pressure fluid eje

49、ction Hoses under hydraulic pressure. 4.1.8 Ejection of parts or materials Ejection of moulds. Ejection of parts. 4.1.9 Slip, trip and fall hazards From spilt mould oil at the infeed parts of the tile machine. 4.2 Noise Hazards From mould collision. From mechanical/pneumatic equipment. 4.3 Hazards from materials used 4.3.1 Contact or inhalation Chemical burns or dermatitis from cement in wet c