EN 12771-1999 en Footwear - Test Methods for Outsoles - Tear Strength《鞋类 鞋底试验方法 撕裂强度》.pdf

1、STDmBSI BS EN L277L-ENGL 2000 M Lb24bb9 0835L82 5T0 BS EN 12 77 1:2000 BRITISH STANDARD Footwear - Test methods for outsoles - Tear strength The European Standard EN 12771:1999 has the status of a British Standard NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW STD-BSI BS EN L

2、277L-ENGL 2000 Lb24669 0835383 437 M , BS EN 12771:2000 direction of the Sector AmdNo. Committee for Materiais and Chemicals, was published under the authority of the standards Committee and comes into effect on 15 March 2000 0 BSI 03-2000 National foreword Date Comments This British Standard is the

3、 official English ianguage version of EN 12771:1999. The UK participation in its preparation was entrusted to Technical Committee TCI/69, Footwear and leather, which has the responsibility to: It peisede J3S 5131-2.61979 which is withdrawn. - aid enquirem to understand the text; - present to the res

4、ponsible European committee any enquiries on the - monitor related international and European developments and promulgate interpretation, or proposals for change, and keep the UK interests informed; them in the UK A list of organbtions represented on this committee can be obtained on request to its

5、secrem. Cross-references The British Standards which implement internaonal or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “Internationai Standards Correspondence Index”, or by using the “Find” faciity of the BSI Standards

6、Ele - 4,O mm f 0,2 mm for semiexpanded and cellular outsoles; - for leather outsole the full thickness shall be tested. The test is being performed with at least 3 specimens. Their uniform thickness (see specification below) shall be obtained by means of an appropriate splitting machine. If feasible

7、, smooth original skin” surfaces of the sample shall remain unchanged in the specimens. This leads to three possible types of specimen: specimen with 2 original “skins” - S 2; specimen with 1 original “skin” - S 1 ; specimen with no original “skin” - S O. The final result shall be based only on spec

8、imens of the same type, which shall be stated in the report. Q BSI 03-2000 STD=BSI BS EN L277L-ENGL 2000 m 1624667 0835187 755 m Page 6 EN 12771:1999 6 Test method Measure the thickness of the test pieces, using the thickness gauge (see 4.4). Mount the test piece in the testing machine; apply a stea

9、dily increasing traction force at a rate of separation of the grips of 100 mm/min f IO mm/min until the piece breaks. Record the force throughout the tearing process. 7 Expression of results The tear strength Ts expressed in newtons per millimetre thickness, is given by the formula T, = F/d where F

10、is the median force in newton, calculated in accordance with the following procedure: From the force peak values of the trace for tear strength, the median peak force (see 3.2) of peak force values is determined by the appropriate method specified below. NOTE In applying the methods described in thi

11、s standard, it should be assumed that the trace being evaluated is a time record of the variation of force during the period of test. Method A (for traces having less than five peaks) Determine the median of the values of the force peaks in the trace. If there is only one force peak, consider its va

12、lue to be the median. Method B (for traces having five to twenty peaks) Consider only the peak values of the central 80% of the complete trace and determine the median peak force of these values. d is the median thickness, in millimetres, of the test piece. The result is expressed as the average of

13、the three determinations. 8 Test report The test report shall include the following information: a) b) c) d) e) date of testing; 9 type of specimen; g) results, expressed in accordance with clause 7; thickness of the test pieces; full description of the samples tested including commercial styles, co

14、des, colours, nature, etc.; reference of this method of test; any deviations from this test method. Q BCI 03-2000 STDmBSI BS EN 12771-ENGL 2000 m 1b24bb9 0835190 b77 W Page 7 EN 12771 : 1999 Dimensions in millimetres Figure 1 - Trouser test piece Dimensions in millimetres Figure 2 - Trouser test pie

15、ce for leather outsoles Q BSI 03-2000 STD.BS1 BS EN 12771-ENGL 2000 M 1624669 0835191 503 M Page 8 EN 12771 : 1999 Figure 3 - Positioning of trouser test piece in testing machine BSI 03-2000 STD-BSI BS EN L2773-ENGL 2000 Lb24667 0835392 44T E Page 9 EN 12771:1999 Bibliography IS0 34-1 : 1994 Rubber,

16、 vulcanized or thermoplastic - Determination of tear strength - Part 1: Trouser, angle and crescent test pieces. O BSI 03-2000 BS EN 12771:2000 STDOBSI BS EN 12771-ENGL 2000 W 1624667 0635193 386 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the independent nati

17、onal body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess t

18、he latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identi of wh

19、ich can be found on the inside front cover. Tel 020 8996 9OOO. Fax: 020 8996 7400. BSI offen members an individual updating service called PLUS which ensures that subscribers automaidy receive the latest editions of standards. Buying standards orders for a BSI, intemational and foreign standards pub

20、lications should be addressed to Customer SeMces. Tel 020 8996 9001. Fax: O20 8996 7001. In response to orders for intemalionai standards, it is BSI policy to supply the BSI implementation of those that have been published as British standards, unless otherwise requested. Information on standards BS

21、I provides a wide range of information on national, European and intemational standards through its Library and its Technical Help to Exporters Service. Various BSI electronic infodon services are also available which give details on ali its products and services. Contact the Infodon Centre. Tel 020

22、 8996 7111. Fax O20 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantia discounts on the purchase price of standards. For details of these and other benefits contact Membership AchhMraQ on. Tel 020 8996 7002. Fax: O20 8996 7001. Copyright Copy

23、right subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international sandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or mnsmiW in any form or b

24、y any means - eleclmnic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. if permission is granted, the terms may include royaity payments or a iicensing agreement. Details and advice can be obtained from the Copynght Manager. Tel: 020 8996 7070.