EN 1294-2000 en Door Leaves - Determination of the Behaviour under Humidity Variations in Successive Uniform Climates《门扉 连续一致气候下湿度不同时的性能测定》.pdf

1、 STD-BSI BS EN L294-ENGL 2000 M Lb24bb9 0859980 440 BRITISH STANDARD Door leaves - Determination of the behaviour under humidity variations in successive uniform climates The European Standard EN 12942000 has the status of a British Standard ICs 91.060.50 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS

2、PERMITTED BY COPYRIGE LAW BS EN 1294:2000 STD-BSI BS EN L294-ENGL 2000 W 1b24bbS 0859981 387 W direction Committee of for the Building Sector and Civil _II.- Engineering, was published under the authority of the Standards Committee and comes into effect on 15 July 2000 O BSI 07-2000 - BS EN 1294:200

3、0 (:omnients National foreword This British Standard is the official English language version of EN 12942OO0, which is included in a package of new European Standards being prepared by CENITC 33 relating to doors. Mer standards included in the package are EN 1121, and EN 12219. Although the Englkh I

4、aiguage versions of these European Standards will be adopted as British Standards as they become available, the existing British Stan- for doors WU be retained, but only untii such time that the complete package of European Standards becomes available. The original group of British Standards wiii th

5、en be withdrawn and this wili be notified in BSI Standards Update. This British Standard will supersede BS 5369: 1987. The UK participation in its preparation was entrusted by Technical Committee B/538, Doors, windows, shutters, hardware and curtain walling, to Subcommittee B/538/2, Doors, which has

6、 the responsibility to: - aid enquirers tci understand the text; - present to the responsible European committee any enquiries on the - monitor related international and European developments and promulgate interpretation, or proposals for change, and keep the UK interests informed; them in the LJK.

7、 A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standastls which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “I

8、nternational Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance wit

9、h a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 4, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when th

10、e document was last issued. ISBN O 580 36103 9 I1 STD.BSI BS EN 12V-ENGL 2000 Lb2Vbb 0859982 213 mI EN 1294 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM February 2000 ICs 91 .O6050 Sepersedes EN 43: 1985 English version Door leaves - Determination of the behaviour under humidity variations in s

11、uccessive uniform climates Vantaux de portes - Dtermination du compoitement aux variations dhumidit entre des climats successifs uniformes Trbltter - Ermittlung des Verhalten bei Feuchtigkeitsnderungen in aufeinanderfolgenden beidseitig gleichen Klimaten This European Standard was approved by CEN on

12、 12 December 1999. CEN members are bound to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographcal references concerning cuch national standards ma

13、y be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by traislation under the responsibility of a CEN member into its own language and notified to the Cen

14、tral Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingd

15、om. EUROPEAN COMMITEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Central Secretariat: rue de Stassart, 36 B-1050 Brussels 8 2000 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1294:2000 E Pag

16、e 2 EN 1294:2000 FOREWORD This European Standard has been prepared by Technical Committee CENTTC 33, Doors, windows, shutters, building hardware and curtain walling, the Secretariat of which is held by AFNOR. This European Standard replaces EN 43:1985, Methods of tesng doors - Behaviour under humidi

17、ty variations of door leaves placed in successive uniform climates. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2000, and conflicting national standards shall be withdrawn at the latest

18、 by August 2000. According to the CENICENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherl

19、ands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. This European Standard has been prepared taking into account IS0 6444 and EN 43. This draft is one of a series of standards for doors. 1 SCOPE This European Standard describes the method which is to be used to test the behavi

20、our under humidity variations of door leaves placed in successive uniform climates. This standard can be applied to all door leaves, (e.g. solid doors, hollow core doors, panelled doors and glazed doors), which are nominally flat and rigid, and which contain hygroscopic materials can might influence

21、 their behaviour during this test. 2 NORMATIVE REFERENCES This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references,

22、 subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 951 EN 952 prEN 1251 9: 1996 Door leaves - Method for measur

23、ement of height, width, thickness and squareness Door leaves - General and local flatness - Measurement method Doors and windows - Terminology 3 DEFINITIONS For the purposes of this Standard the definitions given in prEN 12519:1996 apply. OBSI 07-2000 Page 3 EN 1294:2000 4 PRELIMINARY CONDITIONING P

24、rior to the test, condition the door leaf for at least 7 days in one of these two standard climates: Temperature (20 f 2) “C; Temperature (23 f 2) OC; Relative Humidity (65 f 5) %; Relative Humidity (50 f 5) %. 5 APPARATUS Climate chambers capable of maintaining controlled temperature and humidity.

25、Suitable supporting device for holding the door leaf in a vertical position without imposing any restraint that might affect the development of deformation. Apparatus for measuring general and local flatness in accordance with EN 952. Apparatus for measuflng height and width in accordance with EN 95

26、1. Apparatus for weighing the specimen in accordance with 6.1, 6.2,6.3, 6.4 and 6.5 6 TEST PROCEDURE 6.1 Initial measurement After conditioning the door leaf in accordance with clause 4, measure its height and width in accordance with EN 951, its general flatness in accordance with EN 952, and its m

27、ass. Also measure local flatness in accordance with EN 952 if required. 6.2 Exposure to high humidity Place the door leaf in a climate defined by: Temperature (23 f 2) OC; Relative Humidity (85 f 5) %. The mean values of temperature and relative humidity shall be maintained as close as practicable t

28、o the nominal values: the tolerances are permitted only for purposes of regulation. The duration of exposure to this climate shall be 7 days for doors without applied finish, and 21 days for all other doors. The test may be stopped before the end of the period specified above, if two successive meas

29、urements of general flatness taken at 2 day intervals do not differ by more than 1 % or if the specimen has reached hygroscopic equilibrium (difference in mass between two successive weighings at 2 day intervals less than Oll % of the initial mass). If the test house stops the test before the full d

30、uration of exposure, it shall give reasons for its decision. 6.3 Measurement after exposure to high humidity Remeasure the height and width, the general flatness and the mass of the door leaf. Also remeasure local flatness if required. OBSI 07-2000 Page 4 EN 1294:2000 6.4 Exposure to low humidity Pl

31、ace the door leaf in a climate defined by: Temperature (23 i: 2) OC; Relative Humidity (30 I 5) %. The mean values of temperature and relative humidity shall be maintained as close as practicable to the nominal values; the tolerances are permitted only for purposes of regulation. The duration of exp

32、osure to this climate shall be 7 days for doors without applied finish, and 21 days for all other doors. The test may be stopped before the end of the period specified above, if two successive measurements of general flatness taken at 2 day intervals do not differ by more than I % or if the specimen

33、 has reached hygroscopic equilibrium (difference in mass between two successive weighings at 2 day intervals less than 0,l %). If the test house stops the test before the full duration of exposure, it shall give reasons for its decision. 6.5 Measurement after exposure to low humidity Remeasure the h

34、eight and width, the general flatness and the mass of the door leaf. Also remeasure local flatness if required. 7 EXPRESSION OF RESULTS The results shall be expressed in terms of absolute value and variations in the measurements of the height, width, general flatness, local flatness and mass. The ac

35、curacy of the measurements shall be as prescribed in EN 951 and EN 952. 8 TESTREPORT The test report shall include the following information: a) all necessary details to identify the door leaf; b) all relevant details concerning the type, dimensions, shape and constructional details of the door leaf

36、, the c) description of the device supporting the door leaf during the test; d) duration and characteristics of the conditioning climate if it did not conform to 4; e) reasons for the duration of exposure to the two climates, if shorter than prescribed; 9 the successive measurements of height and wi

37、dth; g) the successive measurements of general flatness, and of local flatness if measured; h) the successive measurements of mass; i) any damage occuring during the test; j) name of the testing laboratory; k) the dates between which the test was performed; I) reference to this European Standard. in

38、itial mass, any machining to receive the hardware, and any applied finish; BS EN 12942000 BSI 389 Chiswick High Road London w4 4AL STD*BSI BS EN 1274-ENGL 2000 Lb2Ybb7 085778b 7b7 BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It

39、 presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that. they possess the latest amendments or editions. It is the constant aim

40、 of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel 020 89

41、96 9OOO. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, intemational and foreign standards publications should be addressed to Customer Servi

42、ces. Tel 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on na

43、tional, European and international standards through its Libraxy and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel 020 8996 7111. Fax: 020 8996 7048. Sub

44、scribing members of BSI are kept, up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copynght subsists in dl RSI publi

45、cations. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no eximct may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic,

46、photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details ancl advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.