EN 12952-18-2012 en Water-tube boilers and auxiliary installations - Part 18 Operating instructions《水管锅炉及附属设备 操作规程》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 12952-18:2012W a t e r - t u b e b o i l e r s a n d auxiliary installationsPart 18: Operating instructionsBS EN 12952-18:2012 BRITISH STANDARDNational forewordThis British

2、 Standard is the UK implementation of EN 12952-18:2012. The UK participation in its preparation was entrusted to TechnicalCommittee PVE/2, Water Tube And Shell Boilers.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport

3、to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012ISBN 978 0 580 74964 3 ICS 27.040 Compliance with a British Standard cannot confer immunity from legal obligations.

4、This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 12952-18:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12952-18 October 2012 ICS 27.040 English V

5、ersion Water-tube boilers and auxiliary installations - Part 18: Operatinginstructions Chaudires tubes deau et installations auxiliaires - Partie 18 : Instructions de service Wasserrohrkessel und Anlagenkomponenten - Teil 18: Betriebsanleitungen This European Standard was approved by CEN on 8 Septem

6、ber 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obt

7、ained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the C

8、EN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Irelan

9、d, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Ma

10、rnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12952-18:2012: EBS EN 12952-18:2012EN 12952-18:2012 (E) 2 Contents Page Foreword 31 Scope 52 Normative references 53 Terms and definitions .54 Objective

11、of operating instructions .65 Content and organisation of operating instructions 65.1 General aspects .65.2 Organisation of the operating instructions .65.3 Plant and process-related aspects 75.4 Operation related aspects .8Annex A (informative) Recommended sections of operating instructions 10Annex

12、 ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC . 11Bibliography . 12BS EN 12952-18:2012EN 12952-18:2012 (E) 3 Foreword This document (EN 12952-18:2012) has been prepared by Technical Committee CEN/TC 269 “Shell and water-tube boi

13、lers”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2013, and conflicting national standards shall be withdrawn at the latest by April 2013. Atten

14、tion is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and

15、 the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive 97/23/EC, see informative Annex ZA, which is an integral part of this document. The European Standard series EN 12952 concerning water-tube boilers and auxiliary installat

16、ions consists of the following parts: Part 1: General; Part 2: Materials for pressure parts of boilers and accessories; Part 3: Design and calculation for pressure parts; Part 4: In-service boiler life expectancy calculations; Part 5: Workmanship and construction of pressure parts of the boiler; Par

17、t 6: Inspection during construction, documentation and marking of pressure parts of the boiler; Part 7: Requirements for equipment for the boiler; Part 8: Requirements for firing systems for liquid and gaseous fuels for the boiler; Part 9: Requirements for firing systems for pulverized solid fuels f

18、or the boiler; Part 10: Requirements for safeguards against excessive pressure; Part 11: Requirements for limiting devices of the boiler and accessories; Part 12: Requirements for boiler feedwater and boiler water quality; Part 13: Requirements for flue gas cleaning systems; Part 14: Requirements fo

19、r flue gas DENOX-systems liquefied pressurized ammonia and ammonia water solution; Part 15: Acceptance tests; Part 16: Requirements for grate and fluidized-bed firing systems for solid fuels for the boiler; BS EN 12952-18:2012EN 12952-18:2012 (E) 4 CR 12952 Part 17: Guideline for the involvement of

20、an inspection body independent of the manufacturer; Part 18: Operating instructions. Although these parts can be obtained separately, it should be recognised that the parts are inter-dependent. As such, the design and manufacture of water-tube boilers requires the application of more than one part i

21、n order for the requirements of the standard to be satisfactorily fulfilled. NOTE A “Boiler Helpdesk“ has been established in CEN/TC 269 which may be contacted for any questions regarding the application of the European Standards series EN 12952 and EN 12953, see the following website: http:/www.boi

22、ler-helpdesk.din.de According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Ma

23、cedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 12952-18:2012EN 12952-18:2012 (E) 5 1 Scope This part of this

24、 European Standard specifies the organisation and content of operating instructions for water-tube boilers and auxiliary installations as defined in EN 12952-1 when placed on the market. To what extent the following aspects are used for the establishment of an operating instruction depends on the st

25、ipulated scope of delivery and of the requirements by contract regarding plant operation and maintenance. NOTE The manufacturers scope of supply may be either pressure equipment, or pressure equipment and “auxiliary” plant such as motors, pumps and fans. 2 Normative references The following document

26、s, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12952-1:2001, Water-tube b

27、oilers and auxiliary installations Part 1: General EN 12952-3:2011, Water-tube boilers and auxiliary installations Part 3: Design and calculation for pressure parts of the boiler EN 12952-6:2011, Water-tube boilers and auxiliary installations Part 6: Inspection during construction; documentation and

28、 marking of pressure parts of the boiler EN 12952-12:2003, Water-tube boilers and auxiliary installations Part 12: Requirements for boiler feedwater and boiler water quality 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12952-1:2001 and the followin

29、g apply. 3.1 Piping and Instrument Diagram (P reasonably foreseeable misuse; and residual hazards that may exist. The aspects given in Clause 5 are to be considered the minimum requirements, where applicable, in the establishment of the operating instructions and do not claim to be complete. 5 Conte

30、nt and organisation of operating instructions 5.1 General aspects The operating instructions shall contain the following: a) manufacturers data (company name, complete address, further contact data, where required, e.g. of the authorised representative established within the European Union); b) info

31、rmation on product identification; c) the year of manufacture; d) reference to copyright protection as regards the operating instructions; e) information on the use of the operating instructions (group of users, availability, explanation of symbols); f) where required, EC conformity declarations, an

32、d declarations of incorporation; g) information on the required qualifications of the operating personnel; h) information affixed to the pressure equipment in accordance with EN 12952-6:2011, Clause 12, with the exception of serial identification. It is recommended that the operating instructions in

33、clude a declaration of exemption from liability (in the case of non-observance of the operating instructions, change of operating instructions, unauthorised changes of the plant). 5.2 Organisation of the operating instructions As regards unmistakable communication of the information contained in the

34、 operating instructions care shall be taken to ensure that: a) the limits of the intended use can be identified without doubt; b) instructions for use have been clearly and unambiguously formulated; c) the sequence of activities to be performed is clearly represented; d) warning and safety notices r

35、egarding misuse and inadequate use are contained; BS EN 12952-18:2012EN 12952-18:2012 (E) 7 e) residual hazards as well as prohibitions have been clearly formulated and represented; f) graphic symbols, terminology and abbreviations are explained at suitable locations; g) figures and tables have been

36、 clearly structured and arranged; h) data on process parameters and set values regarding units of measure and order of magnitude are consistent with the related data on plant parts, displays and screens. As regards the required language of the operating instructions agreements under both public and

37、private law should be considered. 5.3 Plant and process-related aspects The operating instructions shall be established with due consideration of plant and process-related aspects: a) description of the plant (extent of plant; plant concept; functional mode of the plant/plant sections/components; pr

38、ocess characteristics, operational characteristics, technical data) including related representations (drawings, P b) design rules, design data e.g. number of stress cycles, wall thickness allowance due to oxidation, corrosion, erosion, abrasion; c) data on hydrostatic test pressure according to EN

39、12952-3:2011, 5.7.4; d) data on process parameters, performance data (design values, allowable operational parameters, limit values); e) guaranteed properties requirements (parameters to be proven, properties to be observed); f) description of operational modes, e.g. automatic, manual, operation wit

40、hout permanent intervention (without permanent supervision); g) description of functional groups, control circuits; h) interaction of interfaces/system boundaries with upstream/ downstream systems; i) description of safety and protective devices, emergency shut-offs; j) description of signals and an

41、nunciations (optical and acoustical signals, warning signals, alarm annunciations); k) indication of set values, e.g. of items of equipment, position of valves; l) data on loadings (additional loads), moments exerted by connected equipment, and dimensions; m) indication of location/operation of fire

42、 alarms/fire protection possibilities; n) indication of operating supplies, consumables, residual matter (properties, storage, use, disposal); o) data on surrounding atmosphere (temperature, air humidity, sound propagation, contaminations, explosive gases/dust); p) lists (spare parts, wear parts, it

43、ems of equipment, consumers); q) system-overlapping remarks on safety and environmental protection; r) description of residual hazards subject to the hazard analysis on account of pressure; BS EN 12952-18:2012EN 12952-18:2012 (E) 8 s) for installations incorporating auxiliary plant the operating ins

44、tructions supplied with that auxiliary plant shall be part of the boiler operating instructions; t) description of sources of danger, danger areas, other effects, protective measures, emergency measures and other accident prevention measures; u) description of warning notices, warning signs; v) requ

45、irements for personal protection equipment. 5.4 Operation related aspects Operation related aspects shall be considered when establishing the operating instructions: a) assembly, installation, erection (descriptions, drawings, circuitry); b) power plant chemistry (chemical mode of operation, boiler

46、feedwater and boiler water quality according to EN 12952-12:2003); c) provision of operational readiness (start-up check list); d) preparation for plant start-up (initial start-up, upon regular shutdown, upon repairs); e) start-up of plant, start-up conditions (cold start, warm start, hot start); f)

47、 normal operation, commercial service (full load, partial load, load changes); g) for boiler plant permitted to operate without manual intervention (without permanent supervision), the maximum time without manual intervention and any additional inspection or operation criteria shall be specified; h)

48、 operational troubles due to failure of units, inadmissible operational parameters, complete failure of power supply, leakage, fire, deflagrations, release of operational fluids (typical troubles, causes, identification, remedial measures); i) shutdown of plant, shutdown conditions (from commercial

49、service, emergency shutdown); j) inspections, functional checks, functional tests (check/test item, type of check/test), extent of check/test, frequency prior to / during / upon determined operating conditions); k) sampling, analyses; l) technically required periodic inspections (item, method, extent of inspection) unless otherwise agreed in the purchase specification; m) maintenance and service work to be performed, specification of replacement parts and tools to be used; n) performance of repairs and