EN 12953-13-2012 en Shell boilers - Part 13 Operating instructions《壳牌锅炉- 13部分 操作指令》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 12953-13:2012Shell boilersPart 13: Operating instructionsBS EN 12953-13:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 12953-13:

2、2012.The UK participation in its preparation was entrusted to TechnicalCommittee PVE/2, Water Tube And Shell Boilers.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract

3、. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 70581 6ICS 23.020.01; 27.060.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under th

4、e authority of theStandards Policy and Strategy Committee on 29 February 2012.Amendments issued since publicationDate Text affectedBS EN 12953-13:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12953-13 January 2012 ICS 27.060.30 English Version Shell boilers - Part 13: Operating instructio

5、ns Chaudires tubes de fume - Partie 13: Instructions de service Growasserraumkessel - Teil 13: Betriebsanleitungen This European Standard was approved by CEN on 9 December 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this E

6、uropean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official vers

7、ions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria,

8、 Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.

9、EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12953-13:2012: EBS EN 12

10、953-13:2012EN 12953-13:2012 (E) 2 Contents Page Foreword 31 Scope 52 Normative references 53 Terms and definitions .54 Content of operating instructions 54.1 General 54.2 Minimum of content of operating instructions .6Annex ZA (informative) Relationship between this European Standard and the Essenti

11、al Requirements of EU Directive 97/23/EC 7Bibliography 8BS EN 12953-13:2012EN 12953-13:2012 (E) 3 Foreword This document (EN 12953-13:2012) has been prepared by Technical Committee CEN/TC 269 “Shell and water-tube boilers”, the secretariat of which is held by DIN. This European Standard shall be giv

12、en the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2012, and conflicting national standards shall be withdrawn at the latest by July 2012. Attention is drawn to the possibility that some of the elements of this document may be th

13、e subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Direc

14、tive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. The European Standard EN 12953 concerning shell boilers consists of the following parts: Part 1: General Part 2: Materials for pressure parts of boilers and accessories Part 3: Desig

15、n and calculation for pressure parts Part 4: Workmanship and construction of pressure parts of the boiler Part 5: Inspection during construction, documentation and marking of pressure parts of the boiler Part 6: Requirements for equipment for the boiler Part 7: Requirements for firing systems for li

16、quid and gaseous fuels for the boilers Part 8: Requirements for safeguards against excessive pressure Part 9: Requirements for limiting devices of the boiler and accessories Part 10: Requirements for feedwater and boiler water quality Part 11: Acceptance tests Part 12: Requirements for grate firing

17、systems for solid fuels for the boiler Part 13: Operating instructions CR 12953 Part 14: Guideline for involvement of an inspection body independent of the manufacturer BS EN 12953-13:2012EN 12953-13:2012 (E) 4 Although these parts may be obtained separately, it should be recognized that the parts a

18、re interdependent. As such, the design and manufacture of shell boilers requires the application of more than one part in order for the requirements of the European Standard to be satisfactorily fulfilled. For any questions arising when using these standards the Boiler Helpdesk of CEN/TC 269 may be

19、contacted: http:/www.boiler-helpdesk.din.de According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France

20、, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 12953-13:2012EN 12953-13:2012 (E) 5 1 Scope This European Standard identifie

21、s the requirements for the manufacturer to provide operating instructions for pressure equipment supplied in accordance with EN 12953-1 when placed on the market. NOTE Where the equipment or assembly will reach the final user in a Member State which requires translation of operating instructions, ma

22、nufacturers should be aware of this requirement. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including an

23、y amendments) applies. EN 12953-1:2012, Shell boilers Part 1: General EN 12953-6:2011, Shell boilers Part 6: Requirements for equipment for the boiler 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12953-1:2012 and the following apply. 3.1 Piping and

24、 Instrument Diagram (P first startup procedures and measures; normal operation procedures and surveillance; maintenance including scheduled checks by the user residual hazards NOTE See Clause 4. 4 Content of operating instructions 4.1 General The manufacturer shall provide the operating instructions

25、 for all equipment within the scope of supply. NOTE The end user should produce his own operating and maintenance procedures that implement the manufacturers operating instructions to ensure that the boiler is operated properly and safely. BS EN 12953-13:2012EN 12953-13:2012 (E) 6 4.2 Minimum of con

26、tent of operating instructions The minimum content of operating instructions shall include the following: specification used for design as specified in EN 12953-1:2012, Annex A; specifications for safety accessories (e.g. set values) and pressure accessories; requirements for heat supply equipment,

27、and if necessary, specific requirements for heat supply with slow acting combustion (e.g. combustion of wood or other solid fuels) according to EN 12953-6:2011; marking; technical documents, drawings and diagrams where necessary for a full understanding of these instructions; handling, storage and t

28、ransportation requirements; installation and assembly instructions; putting into operation (first start) and commissioning; start-up and shut down procedures (normal and emergency); requirements under foreseen operating conditions; schedule of maintenance and inspection; information on how to deal w

29、ith known or anticipated fault conditions (frequently asked questions); requirements for supervision during boiler operation by the boiler attendant: frequency, methodology and acceptance criteria for periodic tests of safety devices; any residual hazard from the hazard analysis (e.g. danger from fo

30、reseeable misuse). NOTE The hazard analysis itself is not part of the operating instructions. BS EN 12953-13:2012EN 12953-13:2012 (E) 7 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC This European Standard has been prepared

31、under a mandate given to CEN by the European Commission to provide a means of conforming to Essential Requirements of the New Approach Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment.

32、Once this standard is cited in the Official Journal of the European Union under that Directive and has been implemented as a national standard in at least one Member State, compliance with the clauses of this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a pr

33、esumption of conformity with the corresponding Essential Requirements of that Directive and associated EFTA regulations. Table ZA.1 Correspondence between this European Standard and Directive for Pressure Equipment 97/23/EC Clause(s)/subclause(s) of this EN 12953-13 Essential Requirements (ERs) of D

34、irective for Pressure Equipment 97/23/EC Annex I Qualifying remarks/notes 4 1.2 3rdindent 3.4 a) 3.4 b) 3.4 c) Principles to ensure the safety Basic requirements of the hazard analysis Operating instructions WARNING Other requirements and other EU Directives may be applicable to the product(s) falli

35、ng within the scope of this standard. BS EN 12953-13:2012EN 12953-13:2012 (E) 8 Bibliography 1 Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment; OJEC, L181 2 CEN/TS 764-6:2004, Pressure

36、 equipment Part 6: Structure and content of operating instructions This page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and

37、at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8

38、996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone findin

39、g an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offer

40、s BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards dire

41、ctly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply

42、the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email

43、: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding on

44、line access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted

45、 by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be re

46、produced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: