1、BS EN 13215:2016Condensing units forrefrigeration Ratingconditions, tolerances andpresentation of manufacturersperformance dataBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 13215:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementa
2、tion of EN 13215:2016. It supersedes BS EN 13215:2000 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee RHE/17, Testing of air conditioning units.A list of organizations represented on this committee can be obtained on request to its secretary.This publi
3、cation does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 90121 8 ICS 27.200 Compliance with a British Standard cannot confer immunity
4、from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 13215:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13215 Novem
5、ber 2016 ICS 27.200 Supersedes EN 13215:2000English Version Condensing units for refrigeration - Rating conditions, tolerances and presentation of manufacturers performance data Units de condensation pour la rfrigration - Dtermination des caractristiques, tolrances et prsentation des performances du
6、 fabricant Verflssigungsstze fr die Klteanwendung - Nennbedingungen, Toleranzen und Darstellung von Leistungsdaten des Herstellers This European Standard was approved by CEN on 24 September 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions
7、 for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in t
8、hree official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards
9、bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia
10、, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved wor
11、ldwide for CEN national Members. Ref. No. EN 13215:2016 EBS EN 13215:2016EN 13215:2016 (E) 2 Contents Page European foreword . 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 5 4 Symbols and abbreviations . 6 5 Parameters for the presentation of performance data . 7 6 General requirem
12、ents . 7 7 Performance data 8 7.1 General 8 7.2 Part load performance data 8 7.3 Tabular or graphical form . 8 7.4 Determination of the power absorbed by the condensing unit . 8 7.4.1 Condensing units including the compressor motor . 8 7.4.2 Motors with a specific factory assembled or factory specif
13、ied means for variable speed 8 7.4.3 Externally driven compressors without motor 8 8 Rating conditions 9 8.1 General 9 8.2 Standard reference points . 9 8.3 Air cooled condensing units . 10 8.3.1 General . 10 8.3.2 Data for SEPR calculation 10 8.4 Water cooled condensing units . 10 9 Tolerances 10 1
14、0 Correction factors 11 10.1 Superheat 11 10.2 Compressors speed . 11 Annex A (normative) Calculation of SEPR. 12 A.1 General . 12 A.2 Condensing unit without capacity control 12 A.3 Condensing unit with stepwise capacity control 12 A.4 Calculation of SEPR 13 Annex ZA (informative) Relationship betw
15、een this European Standard and the eco-design requirements of Commission Regulation (EU) No 2015/1095 aimed to be covered 16 Bibliography . 18 BS EN 13215:2016EN 13215:2016 (E) 3 Tables Table 1 Symbols and abbreviations 6 Table 2 Indices 7 Table 3 Parameters for the presentation of performance data
16、7 Table 4 Standard reference points 9 Table 5 Actual performance in relation to published data 11 Table A.1 Required input for SEPR calculation . 13 Table A.2 Ambient temperatures and duration for SEPR determination . 14 Table ZA.1 Correspondence between this European Standard and Commission Regulat
17、ion (EU) No 2015/1095 of 5 May 2015 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for professional refrigerated storage cabinets, blast cabinets, condensing units and process chillers and Commissions standardization request M/4
18、95 (Ecodesign) 16 BS EN 13215:2016EN 13215:2016 (E) 4 European foreword This document (EN 13215:2016) has been prepared by Technical Committee CEN/TC 113 “Heat pumps and air conditioning units”, the secretariat of which is held by AENOR. This European Standard shall be given the status of a national
19、 standard, either by publication of an identical text or by endorsement, at the latest by May 2017, and conflicting national standards shall be withdrawn at the latest by May 2017. This document supersedes EN 13215:2000. Attention is drawn to the possibility that some of the elements of this documen
20、t may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive
21、(s). For relationship with EU Directive(s), see informative Annex ZA which is an integral part of this document. The main changes with respect to the previous edition are listed below: a) part load conditions according to M/495 “Standardisation mandate to CEN, CENELEC and ETSI under Directive 2009/1
22、25/EC relating to harmonised standards in the field of Ecodesign” are taken into account; b) inclusion of the calculation of seasonal energy performance ratio (SEPR). According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to imple
23、ment this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
24、 Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 13215:2016EN 13215:2016 (E) 5 1 Scope This European Standard specifies the rating conditions, tolerances and presentation of manufacturers performance data for condensing units for refrigeration with compressors of
25、 the positive-displacement type. These include single stage compressors and single and two stage compressors having an integrated means of fluid sub cooling. This is required so that a comparison of different condensing units can be made. The data relate to the refrigerating capacity and power absor
26、bed and include requirements for part-load performance where applicable. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated refer
27、ences, the latest edition of the referenced document (including any amendments) applies. EN 378-1:2008+A2:2012, Refrigerating systems and heat pumps - Safety and environmental requirements - Part 1: Basic requirements, definitions, classification and selection criteria EN 13771-2, Compressors and co
28、ndensing units for refrigeration - Performance testing and test methods - Part 2: Condensing units ISO 817, Refrigerants Designation and safety classification 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 378-1:2008+A2:2012 and the following apply.
29、3.1 condensing unit combination of one or more compressors, condensers/gas coolers and, where applicable, liquid receivers and the regularly furnished accessories 3.2 refrigerating capacity Q product of the mass flow of refrigerant through the condensing unit and the difference between the specific
30、enthalpy of the refrigerant at the condensing unit inlet, the refrigerant being superheated above the suction dew point temperature to the appropriate value (see Table 3), and the specific enthalpy of the liquid refrigerant at the condensing unit outlet 3.3 sub-cooling difference between the bubble
31、point temperature of the refrigerant corresponding to the pressure at the condensing unit outlet and the temperature of the liquid refrigerant at the condensing unit outlet 3.4 superheat difference between the dew point temperature of the refrigerant corresponding to the pressure at the condensing u
32、nit inlet and the temperature of the refrigerant vapour at the condensing unit inlet BS EN 13215:2016EN 13215:2016 (E) 6 3.5 power absorbed P power demand to drive the condensing unit 3.6 coefficient of performance COP refrigerating capacity to the power absorbed 3.7 seasonal energy performance rati
33、o SEPR reference annual refrigeration demand divided by the annual electrical energy demand 4 Symbols and abbreviations Table 1 Symbols and abbreviations Symbol Designation Unit LT Low evaporating temperature - MT Medium evaporating temperature - HT High evaporating temperature - COP Coefficient of
34、performance - CR Capacity ratio - d Duration h E Annual electrical energy demand kWh P Power W q Refrigeration demand ratio - Q Refrigerating capacity W SEPR Seasonal energy performance ratio - t Temperature C BS EN 13215:2016EN 13215:2016 (E) 7 Table 2 Indices Index Designation LT Low evaporating t
35、emperature MT Medium evaporating temperature amb ambient cor corrected dm demand low low A, B, C and D Rating conditions j bin-number R rated 5 Parameters for the presentation of performance data The parameters as shown in Table 3 shall be used for the presentation of the performance data. Table 3 P
36、arameters for the presentation of performance data Parameters refrigerant Suction temperature (C) or superheat (K) at the condensing unit inlet Condensing unit application Halocarbons and hydrocarbons including refrigerant blends 32 C Household and similar refrigerators/freezers 20 C or 10 K Other a
37、pplications R717 5 K Any application using ammonia R744 32 C Household and similar 10 K Other application using CO2 6 General requirements The performance data of a condensing unit for refrigeration shall be presented in either tabular or graphical form as shown in 7.3. Data outside the allowable wo
38、rking range of the condensing unit shall not be included. The performance of the condensing unit at the standard reference points in Table 4 shall also be reported. To calculate the performance at other suction temperatures/superheat and at other compressor speeds, correction factors shall be given
39、as shown in Clause 10. Refrigerants shall be designated in accordance with ISO 817. The source from which the thermodynamic properties are taken shall be stated. It is recommended that an example illustrating the use of the performance data and the correction factors should be given. Other data such
40、 as the swept volume, number of cylinders and speed range may also be shown. BS EN 13215:2016EN 13215:2016 (E) 8 7 Performance data 7.1 General Published performance shall be based on data obtained from tests performed in accordance with EN 13771-2. The performance data shall be presented as stated
41、in Clause 8 and for: open compressors at the rated speed; motor compressors at the rated voltage and frequency. 7.2 Part load performance data The performance data with capacity control shall be presented for: all capacity control steps for condensing units with 2 to 4 control steps, e.g. blocked su
42、ction, condensing units with more than one compressor or multi-speed compressor motors; condensing units with more than 4 steps or other variable capacity (e.g. variable speed or quasi stepless) at maximum, minimum and at least one additional control step inside the control range. In the case of non
43、linear performance behaviour between published values, the interpolation method, necessary to keep within the tolerances, is to be stated. Part load data for SEPR calculation according to Annex A shall be declared in addition. 7.3 Tabular or graphical form The performance data to be given, in either
44、 tabular or graphical form, shall comprise: a) the refrigerating capacity, in values able to be read to an accuracy of 2 %; b) the power absorbed, in values able to be read to an accuracy of 2 %; c) the evaporating temperature/suction dew point temperature, at intervals not greater than 5 K. 7.4 Det
45、ermination of the power absorbed by the condensing unit 7.4.1 Condensing units including the compressor motor Power absorbed consists of the electrical power input to the compressor motor and the power of the fan(s) and other electrical auxiliaries. 7.4.2 Motors with a specific factory assembled or
46、factory specified means for variable speed The motor power is the electrical power input at the terminals of the frequency inverter or other means for variable speed. 7.4.3 Externally driven compressors without motor Power absorbed consists of the power at the compressor shaft and the power of the f
47、an(s) and other electrical auxiliaries. BS EN 13215:2016EN 13215:2016 (E) 9 8 Rating conditions 8.1 General A rating condition consists of a reference point of Table 4 and an ambient temperature from 8.3 for air cooled condensing unit respectively a condensing temperature from 8.4 for water cooled c
48、ondensing units. The following data shall be given: refrigerating capacity; value of subcooling at the condensing unit outlet; power absorbed, including fan motors and factory supplied accessories; COP. The following further information shall be available upon request: application limits related to
49、air or water temperature (minimum-maximum); for air cooled condensing units: air flow; for water cooled condensing units: water flow and pressure drop. 8.2 Standard reference points The standard reference points shall be in accordance with Table 4. Table 4 Standard reference points Condensing unit applications Reference points Low evaporating temperature (LT) Medium evaporating temperature (MT) High evaporating temperature (HT) Household and similar Evaporating temperature (C) suction dew point 35 10 +5
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1