EN 13282-3-2013 5000 Hydraulic road binders - Part 3 Conformity evaluation《液体公路粘合剂 第3部分 合格评价》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 13282-3:2013Hydraulic road bindersPart 3: Conformity evaluationCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo repro

2、duction or networking permitted without license from IHS-,-,-BS EN 13282-3:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 13282-3:2013.The UK participation in its preparation was entrusted to TechnicalCommittee B/516/14, Special hydraulic road binders.A li

3、st of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLim

4、ited 2013ISBN 978 0 580 69713 5ICS 93.080.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 March 2013.Amendments issued since publicationDate Text affectedCopy

5、right European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 13282-3:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13282-3 March 2013 ICS 93.080.20 English Version Hydraulic road

6、 binders - Part 3: Conformity evaluation Liants hydrauliques routiers - Partie 3: Evaluation de la conformit Hydraulische Tragschichtbinder - Teil 3: Konformittsbewertung This European Standard was approved by CEN on 20 October 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regu

7、lations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN memb

8、er. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. C

9、EN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,

10、 Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and

11、 by any means reserved worldwide for CEN national Members. Ref. No. EN 13282-3:2013: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 13282-3:2013EN 13282-3:2013 (E) 2 Cont

12、ents Page Foreword . 3 1 Scope 4 2 Normative references . 4 3 Terms and definitions 4 3.1 Specific definitions 4 3.2 General definitions . 5 4 Factory production control by the manufacturer 6 4.1 General requirements 6 4.1.1 Concept 6 4.1.2 Works quality manual 6 4.1.3 Management systems 7 4.1.4 Sys

13、tem of documentation 7 4.2 Internal quality control . 8 4.2.1 Process control 8 4.2.2 Measuring and testing . 8 4.2.3 Handling, storage, packaging and delivery . 8 4.3 Autocontrol testing of samples . 8 4.3.1 Sampling and testing . 8 4.3.2 Evaluation of results of autocontrol testing of samples 9 4.

14、3.3 Corrective action 9 4.3.4 Measuring and test equipment for autocontrol testing 9 4.3.5 Quality records . 10 5 Initial type testing . 10 6 Assessment of the factory production control . 10 6.1 Surveillance, assessment and acceptance of the factory production control 10 6.1.1 Inspection tasks . 10

15、 6.1.2 Frequency of inspections 10 6.1.3 Reports . 10 6.2 Initial inspection of the factory and the factory production control 10 6.2.1 Inspection of a new factory . 10 6.2.2 Inspection of an existing factory . 10 6.2.3 Criteria for the assessment of the production equipment . 11 6.2.4 Criteria for

16、the activities of the laboratories . 11 6.2.5 Reports . 11 7 Actions in the event of non-conformity . 11 7.1 Actions to be taken by the manufacturer 11 7.2 Actions to be taken in case of a non-conforming factory production control system . 12 8 Requirement for dispatching centres 12 8.1 General . 12

17、 8.2 Tasks for the intermediary . 12 8.2.1 Quality control 12 8.2.2 Confirmation autocontrol testing of samples taken at the dispatching centre . 12 Bibliography 14 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking perm

18、itted without license from IHS-,-,-BS EN 13282-3:2013EN 13282-3:2013 (E) 3 Foreword This document (EN 13282-3:2013) has been prepared by Technical Committee CEN/TC 51 “Cement and building limes”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national

19、standard, either by publication of an identical text or by endorsement, at the latest by September 2013, and conflicting national standards shall be withdrawn at the latest by September 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of paten

20、t rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. This European Standard, EN 13282, Hydraulic road binders consists

21、 of the following parts: Part 1: Rapid hardening hydraulic road binders Composition, specifications and conformity criteria Part 2: Normal hardening hydraulic road binders Composition, specifications and conformity criteria Part 3: Conformity evaluation According to the CEN/CENELEC Internal Regulati

22、ons, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy

23、, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking pe

24、rmitted without license from IHS-,-,-BS EN 13282-3:2013EN 13282-3:2013 (E) 4 1 Scope This European Standard specifies the scheme for the evaluation of conformity of hydraulic road binders to their corresponding product specification standards EN 13282-1 and prEN 13282-2. This European Standard provi

25、des technical rules for factory production control by the manufacturer, including autocontrol testing of samples. It also provides rules for actions to be followed in the event of non-conformity. 2 Normative references The following documents, in whole or in part, are normatively referenced in this

26、document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 196-1, Methods of testing cement Part 1: Determination of strength EN 196-2, Methods

27、of testing cement Part 2: Chemical analysis of cement EN 196-3, Methods of testing cement Part 3: Determination of setting times and soundness EN 196-7, Methods of testing cement Part 7: Methods of taking and preparing samples of cement EN 13282-1:2013, Hydraulic road binders Part 1: Rapid hardening

28、 hydraulic road binders Composition, specifications and conformity criteria prEN 13282-2:2013, Hydraulic road binders Part 2: Normal hardening hydraulic road binders Composition, specifications and conformity criteria 3 Terms and definitions For the purposes of this document, the following terms and

29、 definitions apply. 3.1 Specific definitions 3.1.1 factory production control permanent internal control of hydraulic road binder production exercised by the manufacturer consisting of internal quality control complemented by autocontrol testing 3.1.2 initial period immediate period after the first

30、issuing of the certificate of conformity for a hydraulic road binder 3.1.3 factory facility used by a manufacturer applying a production control for the production of hydraulic road binders, using equipment which is suitable for continuous mass production of hydraulic road binder including, in parti

31、cular, equipment for adequate grinding and homogenisation and the necessary silo capacity for the storage and dispatch of each hydraulic road binder produced, in order to ensure that the requirements of EN 13282 are met 3.1.4 new factory factory which is not already producing hydraulic road binder(s

32、) certified under this scheme Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 13282-3:2013EN 13282-3:2013 (E) 5 3.1.5 existing factory factory which is already producing hy

33、draulic road binder(s) certified under this scheme 3.1.6 depot bulk hydraulic road binder handling facility (not located at the factory) used for the dispatch of hydraulic road binder (whether in bulk or bagged) after transfer or storage where the manufacturer has full responsibility for all aspects

34、 of the quality of the hydraulic road binder 3.1.7 dispatching centre bulk hydraulic road binder handling facility (not located at the factory) used for the dispatch of hydraulic road binder (whether in bulk or bagged) after transfer or storage where an intermediary has full responsibility for all a

35、spects of the quality of the hydraulic road binder 3.1.8 intermediary natural or legal person who takes from the manufacturer bulk hydraulic road binder declared according to this European Standard and bearing the conformity marking, who undertakes full responsibility for maintaining in a bulk handl

36、ing facility all aspects of the quality of the hydraulic road binder and who supplies the hydraulic road binder onwards to a further person 3.1.9 works quality manual document that provides information on the factory production control which is applied by a manufacturer at a particular factory to en

37、sure conformity of the hydraulic road binder with the requirements of the relevant product specification standard 3.1.10 confirmation autocontrol testing continual testing carried out by an intermediary which consists of testing of samples taken by the intermediary at the point(s) of release from th

38、e dispatching centre 3.2 General definitions 3.2.1 Definition from EN ISO 9000 3.2.1.1 quality control part of quality management focused on fulfilling quality requirements SOURCE: EN ISO 9000:2005, 3.2.10 3.2.2 Definitions from EN 13282-1, prEN 13282-2, EN 197-1 and EN 196-7 3.2.2.1 autocontrol tes

39、ting continual testing by the manufacturer of rapid hydraulic road binder spot samples taken at the point(s) of release from the factory/depot SOURCE: EN 13282-1:2013, 3.1 3.2.2.2 control period period of production and dispatch identified for the evaluation of the autocontrol test results SOURCE: E

40、N 13282-1:2013, 3.2 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 13282-3:2013EN 13282-3:2013 (E) 6 3.2.2.3 spot sample sample taken at the same time and from one and the

41、 same place, relating to the intended tests, and which can be obtained by combining one or more immediately consecutive increments SOURCE: EN 197-1:2011, 3.14 3.2.2.4 specified characteristic value characteristic value of a mechanical, physical or chemical property which in the case of an upper limi

42、t is not to be exceeded or in the case of a lower limit is, as a minimum, to be reached SOURCE: EN 13282-1:2013, 3.4 3.2.2.5 single result limit value value of a mechanical, physical or chemical property which - for any single test result in the case of an upper limit is not to be exceeded or in the

43、 case of a lower limit is, as a minimum, to be reached SOURCE: EN 13282-1:2013, 3.5 4 Factory production control by the manufacturer 4.1 General requirements 4.1.1 Concept Factory production control means the permanent internal control of hydraulic road binder production exercised by the manufacture

44、r and consists of internal quality control (see 4.2) complemented by autocontrol testing of samples of hydraulic road binder taken at the point of release1)(see 4.3). NOTE The requirements of this European Standard regarding factory production control take account of those clauses of EN ISO 9001 3 w

45、hich are relevant to the production, process control and testing of hydraulic road binder. 4.1.2 Works quality manual The manufacturers documentation and procedures for factory production control shall be described in a Works quality manual, which shall adequately describe, among other things: a) th

46、e quality aims and the organisational structure, responsibilities and powers of the management with regard to product quality and the means to monitor the achievement of the required product quality and the effective operation of the internal quality control (see 4.1.3); b) the manufacturing and qua

47、lity control techniques, processes and systematic actions that will be used (see 4.2.1, 4.2.3 and 4.3.2); c) the inspections and tests that will be carried out before, during and after manufacture, and the frequency with which they will be carried out (see 4.2.2, 4.3.1 and 4.3.3). The Works quality

48、manual prepared by the manufacturer for each factory shall include an adequate system of documentation (see 4.1.4 and 4.3.4). The Works quality manual shall address and document the procedures operated to ensure that the manufactured hydraulic road binder conforms to the technical specifications. Th

49、e manual may reference 1) This testing corresponds also to the “testing of samples taken at the factory in accordance with the prescribed test plan“ mentioned in Annex V Section 1.3 point (iii) of the Construction Products Regulation No 305/2011 of the European Parliament and of the Council 6. Copyright European Committee for Stan