1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 13411-4:2011Terminations for steel wireropes SafetyPart 4: Metal and resin socketingBS EN 13411-4:2011 BRITISH STANDARDNational forewordThis British Standard is the UK impl
2、ementation of EN 13411-4:2011.It supersedes BS EN 13411-4:2002+A1:2008 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MHE/2, Wire ropes.A list of organizations represented on this committee can beobtained on request to its secretary.This publication do
3、es not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 66753 4ICS 53.020.30; 77.140.99Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the a
4、uthority of theStandards Policy and Strategy Committee on 30 April 2011.Amendments issued since publicationDate Text affectedBS EN 13411-4:2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13411-4 March 2011 ICS 77.140.99 Supersedes EN 13411-4:2002+A1:2008English Version Terminations for stee
5、l wire ropes - Safety - Part 4: Metal and resin socketing Terminaisons pour cbles en acier - Scurit - Partie 4: Manchonnage laide de mtal et de rsine Endverbindungen fr Drahtseile aus Stahldraht - Sicherheit - Teil 4: Vergieen mit Metall und Kunstharz This European Standard was approved by CEN on 19
6、 February 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may
7、be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to
8、 the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxe
9、mbourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rig
10、hts of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13411-4:2011: EBS EN 13411-4:2011EN 13411-4:2011 (E) 2 Contents Page Foreword 4Introduction .51 Scope 62 Normative references 63 Terms and definitions .64 List of significant hazards 85 Safety r
11、equirements and/or protective measures 95.1 General 95.2 Preparation of rope and socket 95.2.1 General 95.2.2 Length marking of rope .95.2.3 Serving 95.2.4 Cutting of rope .95.2.5 Cleanliness of socket . 105.2.6 Inserting rope into socket 105.2.7 Opening the brush 105.2.8 Pre-treatment of the brush
12、. 115.2.9 Hooking 115.2.10 Positioning and alignment of brush, rope and socket 115.2.11 Sealing . 125.3 Socketing . 125.3.1 General . 125.3.2 Molten metal socketing 125.3.3 Resin socketing 135.4 Removal of sealing material 145.5 Protection 145.6 Type testing . 146 Verification of the safety requirem
13、ents and/or measures 146.1 Length marking of rope 146.2 Serving . 146.3 Cleanliness of socket . 146.4 Opening the brush 146.5 Degreasing the brush . 146.6 Hooking 156.7 Positioning and alignment of brush, rope and socket 156.8 Pre-heating the socket . 156.9 Melting the metal. 156.10 Pouring the meta
14、l 156.11 Cooling . 156.12 Pouring the resin 156.13 Curing of the resin 156.14 Removal of sealing . 156.15 After completion of the socketing. 157 Information for use . 167.1 General . 167.2 Marking 167.3 Socketing manufacturers certificate 16BS EN 13411-4:2011EN 13411-4:2011 (E) 3 Annex A (normative)
15、 Molten metal socketing media 17A.1 Lead-based alloys . 17A.2 Zinc . 17A.3 Zinc-based alloy 17Annex B (normative) Resin socketing media . 18B.1 General . 18B.2 Physical properties . 18Annex C (normative) Type testing for assessment of molten metal or resin socketed termination . 19C.1 General . 19C.
16、2 Method of test 19C.3 Acceptance criteria . 19C.4 Test report 19Annex D (informative) Procedure for pre-treatment of bright rope for improved adhesion when socketing with lead-based alloys 20D.1 General . 20D.2 Fluxing 20D.3 Coating . 20Annex E (normative) Operating temperature limits 21Annex F (in
17、formative) Approved socket design parameters 22Annex ZA (informative) Relationship between this European Standard And the Essential Requirements of EU Directive 2006/42/EC 23Bibliography 24BS EN 13411-4:2011EN 13411-4:2011 (E) 4 Foreword This document (EN 13411-4:2011) has been prepared by Technical
18、 Committee CEN/TC 168 “Chains, ropes, webbing, slings and accessories - Safety”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2011, and confli
19、cting national standards shall be withdrawn at the latest by September 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This docu
20、ment supersedes EN 13411-4:2002+A1:2008. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is
21、an integral part of this document. This second edition incorporates both technical and editorial amendments, with the following main changes made with respect to the previous edition: enhance approved socket dimension criteria negating need for type testing and move data into informative Annex F; ad
22、d definition for socketing manufacturer; re-draft hazards clause; re-draft standard in accordance with rules of ISO/IEC Directives, Part 2 and CEN Guide 414. EN 13411, under the general title “Terminations for steel wire ropes Safety”, consists of the following parts: Part 1: Thimbles for steel wire
23、 rope slings; Part 2: Splicing of eyes for wire rope slings; Part 3: Ferrules and ferrule-securing; Part 4: Metal and resin socketing; Part 5: U-bolt wire rope grips; Part 6: Asymmetric wedge socket; Part 7: Symmetric wedge socket; Part 8: Swage terminals and swaging. According to the CEN/CENELEC In
24、ternal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lux
25、embourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 13411-4:2011EN 13411-4:2011 (E) 5 Introduction This European Standard is a type C standard as stated in EN ISO 12100. The machinery concerned and the extent to
26、 which hazards, hazardous situations and events are covered are indicated in the scope of this standard. When provisions of this type C standard are different from those which are stated in type B standards, the provisions of this type C standard take precedence over the provisions of the other stan
27、dards, for machines that have been designed and built according to the provisions of this type C standard. The methods of socketing described in this standard are based on established procedures and following them is considered to result in a rope termination having an efficiency of 100 % based on t
28、he minimum breaking force of the rope. It is assumed that the socket is: suitable for heating without changing the characteristics of the socket material when the socketing medium is molten metal; strong enough for the rope; and suitable for the purpose for which it is intended. BS EN 13411-4:2011EN
29、 13411-4:2011 (E) 6 1 Scope This European Standard specifies the minimum requirements for the molten metal and resin socketing of steel wire ropes within the scopes of EN 12385-4:2002+A1:2008; EN 12385-5:2002; EN 12385-6:2004; EN 12385-7:2002; EN 12385-8:2002; EN 12385-9:2002 and EN 12385-10:2003+A1
30、:2008. The European Standard is applicable only to those requirements that ensure that the socketing is strong enough to withstand a force of at least 100 % of the minimum breaking force of the rope (i.e. socket termination efficiency factor KT= 1,0). NOTE Rope terminations made by socketing in acco
31、rdance with this European Standard can be used for determining the breaking force of wire ropes in accordance with EN 12385-1:2002+A1:2008, Annex A. Socketing by the methods and materials described in this standard are for use within the temperature limits given in normative Annex E. This European S
32、tandard deals with all significant hazards, hazardous situations and events relevant to metal and resin socket terminations, when they are used as intended and under conditions of misuse which are reasonably foreseeable (see Clause 4). 2 Normative references The following referenced documents are in
33、dispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 59, Glass reinforced plastics Measurement of hardness by means of a Barcol impressor EN
34、 1774:1997, Zinc and zinc alloys Alloys for foundry purposes Ingot and liquid EN 12385-1:2002+A1:2008, Steel wire ropes Safety Part 1: General requirements EN 12385-2:2002+A1:2008, Steel wire ropes Safety Part 2: Definitions, designation and classification EN ISO 75-2:2004, Plastics Determination of
35、 temperature of deflection under load Part 2: Plastics, ebonite and long-fibre-reinforced composites (ISO 75-2:2004) EN ISO 604, Plastics Determination of compressive properties (ISO 604:2002) EN ISO 3838, Crude petroleum and liquid or solid petroleum products Determination of density or relative de
36、nsity Capillary-stoppered pyknometer and graduated bicapillary pyknometer methods (ISO 3838:2004) EN ISO 12100:2010 Safety of machinery General principles for design Risk assessment and risk reduction (ISO 12100:2010) 3 Terms and definitions For the purpose of this document, the terms and definition
37、s given in EN ISO 12100, EN 12385-2:2002+A1:2008 and the following apply. 3.1 socket type of wire rope termination incorporating a socket basket BS EN 13411-4:2011EN 13411-4:2011 (E) 7 3.2 socket basket area of a socket in which a brushed rope end is secured using a socketing medium NOTE Description
38、s of further elements of the socket geometry are shown in Figure 1. Key 1 length of tapered basket plus any parallel portion(s) including any radius at rope entry 2 small end of tapered basket 3 large end of tapered basket 4 included angle of tapered basket 5 bore (internal diameter at rope entry) 6
39、 pin hole centre line 7 length of tapered basket 8 length of parallel portion including any radius at rope entry 9 protruding wires 10 length of brush 11 root of brush NOTE Some sockets can have baskets with an extended parallel portion at the large end of the tapered basket. Figure 1 Nomenclature o
40、f typical parts of socket and brush 3.3 serving wrapping, usually of wire or strand, for the purpose of securing a rope end to prevent its unlaying 3.4 permanent serving serving applied prior to socketing and remaining in place at least until the socketing operation has been completed 3.5 temporary
41、serving serving applied and subsequently removed at various stages of the socketing operation 3.6 gelling change in condition of resin from liquid to a semi-solid, jelly-like composition 3.7 hooking procedure whereby the end of a wire forming part of a brush is bent backwards to form a hook BS EN 13
42、411-4:2011EN 13411-4:2011 (E) 8 3.8 socketer competent person carrying out the socketing 3.9 competent person designated person, suitably trained, qualified by knowledge and experience and with the necessary instructions to ensure that the required operations are correctly carried out 3.10 socketing
43、 system method of attachment comprising instructions and materials for the socketing of wire ropes with molten metal or resin 3.11 socketing system designer person or organization that designs the socketing system and assumes responsibility for type testing 3.12 socketing manufacturer person or orga
44、nization that manufactures socketed terminations in accordance with the socketing system designers instructions 4 List of significant hazards This clause contains all the significant hazards, hazardous situations and events for the molten metal and resin socketing of steel wire ropes within the scop
45、es of EN 12385-4:2002+A1:2008; EN 12385-5:2002; EN 12385-6:2004; EN 12385-7:2002; EN 12385-8:2002; EN 12385-9:2002 and EN 12385-10:2003+A1:2008, as far as these hazards are dealt with in this European Standard, identified by risk assessment as significant for socket terminations that require action
46、to eliminate or reduce risk. In particular, the hazard caused by accidental release of a load due to failure of the socketed portion of a socketed rope termination puts at risk, either directly or indirectly, the safety or health of those persons within the danger zone. In order to provide the neces
47、sary strength of the socketed portion of a socketed termination, this European Standard gives requirements for the method of socketing to ensure specified levels of performance are met. Table 1 contains those hazards that require action to reduce risk identified by risk assessment as being specific
48、and significant for socketed termination assemblies. Table 1 Hazards identified EN ISO 14121-1:2007, A.1 and A.4 Type or group Origin Potential consequences Mechanical hazards - Acceleration, deceleration (kinetic energy) - Falling objects - Moving elements - Impact - Crushing Hazardous events - Stability of the machine and/or parts of the machine - Mechanical strength of parts of - Loss of stability - Break-up during BS EN 13411-4:2011EN 13411-4:2011 (E) 9 the machine operation 5 Safety requirements and/or protective measures 5.1 General Machinery shall
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1