1、BRITISH STANDARD BS EN 13414-3:2003+A1:2008Steel wire rope slings Safety Part 3: Grommets and cable-laid slingsICS 53.020.30g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g5
2、3g44g42g43g55g3g47g36g58This British Standard was published under the authority of the Standards Committee and comes into effect on 17 September 2003BS EN 13414-3:2003+A1:2008National forewordThis British Standard is the UK implementation of EN 13414-3:2003+A1:2008. It supersedes BS EN 13414-3:2003
3、which is withdrawn. The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by . The UK participation in its preparation was
4、 entrusted to Technical Committee MHE/2, Wire ropes.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance
5、with a British Standard cannot confer immunity from legal obligations.ISBN Amendmentsg18corrigenda issued since publication Date Comments Implementation of CEN amendment A1:2008 BSI 2009 30 April 2009 978 0 580 60264 1 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13414-3:2003+A1 November 200
6、8 ICS 53.020.30 Supersedes EN 13413-3:2003 English Version Steel wire rope slings - Safety - Part 3: Grommets and cable-laid slings Elingues en cbles dacier - Scurit - Partie 3: Estropes et lingues en grelin Anschlagseile aus Strahldrahtseilen - Sicherheit - Teil 3: Grummets und Kabelschlag-Anschlag
7、seile This European Standard was approved by CEN on 25 March 2003 and includes Corrigendum 1 issued by CEN on 5 May 2004 and Amendment 1 approved by CEN on 18 September 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Euro
8、pean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (Engli
9、sh, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria,
10、 Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATI
11、ON C O M I T E U R O P E N D E N O R M A LI S A T I O N EUR OP IS C HES KOM ITEE FR NOR M UNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13414-3:2003+A1:2008: EEN 134
12、14-3:2003+A1:2008 (E) 2 Contents Page Foreword3 Introduction .4 1 Scope 4 2 Normative references 4 3 Terms and Definitions .5 4 Hazards .6 5 Safety requirements and/or measures 6 6 Verification of the safety requirements and/or measures .10 7 Information for use 10 Annex A (normative) Combination of
13、 lay factors for grommets and cable-laid slings 11 Annex B (normative) Determination of the length of a grommet12 Annex C (normative) Pin sizes for measurements of lengths 14 Annex D (normative) Hand splices 15 Annex E (normative) Certificate for grommets.16 Annex F (normative) Certificate for cable
14、-laid slings 17 Annex G (informative) Tables of working load limits.18 Annex ZA (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC“.26 Annex ZB (informative) !Relationship between this European Standard and the Essential Requirements of
15、 EU Directive 2006/42/EC“.27 BS EN 13414-3:2003+A1:2008EN 13414-3:2003+A1:2008 (E) 3 Foreword This document (EN 13414-3:2003+A1:2008) has been prepared by Technical Committee CEN/TC 168 “Chains, ropes, webbings, slings and accessories - Safety”, the secretariat of which is held by BSI. This European
16、 Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2009, and conflicting national standards shall be withdrawn at the latest by December 2009. This document supersedes EN 13414-3:2003. This document includes
17、Amendment 1, approved by CEN on 2008-09-18 and Corrigendum 1 issued by CEN on 2004-05-05. The start and finish of text introduced or altered by amendment is indicated in the text by tags !“. The modifications of the related CEN Corrigendum have been implemented at the appropriate places in the text
18、and are indicated by the tags . This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). !For relationship with EU Directive(s), see informative Annexes ZA and ZB, which ar
19、e integral parts of this document.“ The other parts of this European Standard are: Part 1 Slings for general lifting service Part 2 Specification for information for use and maintenance to be provided by the manufacturer Annexes A to F are normative. Annex G is informative. According to the CEN/CENE
20、LEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxemb
21、ourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 13414-3:2003+A1:2008EN 13414-3:2003+A1:2008 (E) 4 Introduction This Part of the standard has been prepared to provide a means of complying with the essential safety r
22、equirements of the Machinery Directive and associated EFTA regulations. Purchasers are advised to specify in their purchasing contract that the supplier operates a quality management system applicable to this standard (e.g. ISO EN 9001) to ensure that products claimed to comply consistently achieve
23、the required level of quality. The coefficient of utilization (Zp) used in this standard for slings with a diameter greater than 60 mm is lower than that normally used for general service wire rope slings. This is justified for the following reasons. a) Slings over 60 mm diameter are not intended fo
24、r general service and are subjected to special conditions relating to design, construction, frequency of use, service and discard. b) The mass of the load is generally calculated or measured with considerable accuracy and as such slings are usually specially manufactured for one or a limited number
25、of special lifts. c) The lifting operation is controlled and supervised. d) The dynamic factors, e.g. shock loading, are limited. These factors reduce the unknown aspects which dictate that slings in general service require a higher coefficient of utilization; lower coefficients have been and are us
26、ed with confidence. 1 Scope This European Standard specifies the construction requirements, calculation of WLL, testing and certification of steel wire rope grommets, cable-laid grommets and cable-laid slings using strand and wire rope conforming to EN 12385-4. The hazards covered by this standard a
27、re identified in clause 4. This standard covers ferrule-secured cable-laid slings up to 60mm. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and t
28、he publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to, applies. EN
29、292-2:1991/A1:1995, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles and specifications (Amendment 1: 1995) EN 1050:1996, Safety of machinery Principles for risk assessment EN 12385-4:2002, Steel wire ropes Safety Part 4: Stranded ropes for general lifti
30、ng applications prEN 13411-3, Terminations for steel wire ropes Safety Part 3: Ferrules and ferrule securing BS EN 13414-3:2003+A1:2008EN 13414-3:2003+A1:2008 (E) 5 3 Terms and Definitions For the purposes of this standard the following terms and definitions apply. 3.1 wire rope grommet endless wire
31、 rope sling made from one continuous length of strand, formed to make a body composed of six strands around a strand core NOTE The strand ends are tucked into the body forming the core, with the tuck position diametrically opposite to the core butt position. 3.2 cable-laid grommet endless wire rope
32、sling made from one or two continuous lengths of rope, formed to make a body composed of six ropes around a rope core NOTE The rope ends are tucked into the body forming the core, with the tuck position(s) diametrically opposite to the core butt position(s). 3.3 cable-laid sling sling formed from a
33、wire rope constructed of six unit ropes laid as outers over one core unit rope, with a termination at each end, usually in the form of a spliced eye 3.4 working load limit (WLL) maximum mass which a sling is authorized to sustain in general service 3.5 competent person designated person, suitably tr
34、ained, qualified by knowledge and practical experience, and in possession of the necessary instructions to enable the required calculation of WLL and examination to be carried out 3.6 nominal diameter of grommet or cable laid sling dimension by which the sling is designated BS EN 13414-3:2003+A1:200
35、8EN 13414-3:2003+A1:2008 (E) 6 4 Hazards Accidental release of a load, or release of a load due to failure of a sling or a component puts at risk, either directly or indirectly, the safety or health of those persons within the danger zone. These aspects of safe use associated with good practice are
36、given in prEN 13414-2. Table 1 contains all the hazards which require action to reduce risk identified by risk assessment as being specific and significant for slings and their components. Table 1 Hazards and associated requirements Hazards identified in annex A of EN 1050 : 1996 Relevant clause of
37、annex A of EN 292-2: 1991/A1: 1995 Relevant clause/sub-clause of this Part of EN 13414 1.1.5 Mechanical hazard due 4.1.2.3 5 and 6 to inadequacy of 4.1.2.5 5 and 6 strength 4.1.2.4 7 4.3.2 7 10.4 Errors of fitting hazard 1.5.4 5 5 Safety requirements and/or measures 5.1 Grommets 5.1.1 Production of
38、grommets During the production of grommets a temporary rigid core shall be used. Grommets and cable-laid ropes shall be produced using a method which ensures that the rope or strand tensions are equalized and that the finished product is free from visible waviness. 5.1.2 Construction of wire rope gr
39、ommet The strand used to form the wire rope grommet shall be one of those used to form ropes specified in table 2, 4, 6, 8, 11, 12 and 13 of EN 12385-4:2002. The length of the circumference shall be at least five times the grommet lay length. The core butt position shall be clearly marked by red pai
40、nt applied over any serving. 5.1.3 Construction of cable-laid grommet Cable-laid grommets shall be constructed in accordance with A.1. The unit ropes shall be of 6- or 8-strand construction selected from those specified in tables 2, 3, 4, 5, 6, 7, 8, 11, 12 and 13 of EN 12385-4:2002. Ropes over 60 m
41、m diameter shall have steel rope cores. The length of the circumference shall be at least five times the grommet lay length. The core butt position shall be clearly marked by red paint applied over any servings. NOTE The grommet should never be bent at this marked position. BS EN 13414-3:2003+A1:200
42、8EN 13414-3:2003+A1:2008 (E) 7 5.1.4 Length of grommet The length of a grommet shall be the length of its circumference, measured along its centreline (see fig 1). For wire rope grommets the tolerance shall be 1d or 1% of the nominal length whichever is the greater. For cable-laid grommets construct
43、ed from unit ropes with a fibre core of 24mm g148 d g148 60mm the tolerance shall be 1d or 1% of the nominal length whichever is the greater. For cable-laid grommets constructed from unit ropes with a steel core of 24mm g148 d g148 60mm the tolerance shall be 1d or 1% of the nominal length whichever
44、 is the greater. For cable-laid grommets constructed from unit ropes with a steel core of 66mm g148 d g148 696mm the tolerance shall be 0,5d or 0,5% of the nominal length whichever is the greater. NOTE Two methods of determination of the length of grommets, either by measuring the distance of the be
45、aring points or, more accurately, by measurement of the circumference are described in annex B. For the measurement process pin sizes shall conform to annex C. Figure 1 Wire rope grommet 5.2 Cable-laid slings 5.2.1 Construction of cable-laid sling Cable-laid slings shall be constructed in accordance
46、 with A.2. The unit ropes used shall be of 6- or 8-strand construction selected from those specified in tables, 2, 3, 4, 5, 6, 7, 8, 11, 12 and 13 of EN 12385-4:2002. Cable-laid ropes over 60 mm diameter shall have steel rope cores. If the turn-back loop system for terminations is used, it shall con
47、form to prEN 13411-3. Only unit ropes with a steel core shall be used. Splices shall be made in accordance with annex D. 5.2.2 Length of cable-laid slings The length, L, of a sling, shall be the internal length between the bearing points of each termination whether they are soft eyes, thimbles, or h
48、ooks or links, as appropriate (see figure 2). BS EN 13414-3:2003+A1:2008EN 13414-3:2003+A1:2008 (E) 8 NOTE 1 When measuring the actual length of a sling with soft eyes, dimension w should be approximately h (see figure 2) with h being approximately 15d. The tolerance of length of ferrule-secured and
49、 spliced cable-laid slings shall be 2d or 1% of the nominal length, whichever is the greater. This applies for diameters 24mm g148 d g148 696mm. When measuring length under load, for instance when two or more slings are required to be accurately matched for length, this shall be undertaken at 3 % of the calculated sling breaking force using pins having diameters conforming to Annex C. NOTE 2 The dimensions of the eye should be selected so that h is approximately 15d. 5.2.3 Length of matched sets Where single leg cable-laid slings are
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1