EN 13476-2-2007 en Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U) polypro.pdf

1、BRITISH STANDARDBS EN 13476-2:2007Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 2: Specifications for pipes and fittings with smooth internal and e

2、xternal surface and the system, Type AThe European Standard EN 13476-2:2007 has the status of a British StandardICS 23.040.20; 93.030g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g5

3、0g51g60g53g44g42g43g55g3g47g36g58BS EN 13476-2:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2007 BSI 2007ISBN 978 0 580 53623 6National forewordThis British Standard is the UK implementation of EN 13476-2:2007. It does not supe

4、rsede any current British Standards. However, the Water Industry has indicated that following the publication of this British Standard, Industry Specification WIS 4-35-01 will be declared obsolescent by 29 May 2009 and retained for reference where applicable. The UK participation in its preparation

5、was entrusted by Technical Committee PRI/88, Plastics piping systems and components, to Subcommittee PRI/88/1, Thermoplastics piping systems and components for non-pressure applications.A list of organizations represented on this subcommittee can be obtained on request to its secretary. Sewerage und

6、ertakers and other entities deemed to be within the scope of the Public Procurement Directive (PPD) are obliged to use Parts 1 to 3 of this series of European Standards, produced under EC/U mandate, if they are to comply with structured wall pipe systems or components within its scope. National Anne

7、x NA (informative) gives additional guidance on the use of Parts 1 to 3 of BS EN 13476:2007. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from lega

8、l obligations. Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13476-2May 2007ICS 93.030English VersionPlastics piping systems for non-pressure underground drainageand sewerage - Structured-wall piping systems of unplasticizedpoly(vinyl chlo

9、ride) (PVC-U), polypropylene (PP) andpolyethylene (PE) - Part 2: Specifications for pipes and fittingswith smooth internal and external surface and the system, TypeASystmes de canalisations en plastiques pour lesbranchements et les collecteurs dassainissement sanspression enterrs - Systmes de canali

10、sations paroisstructures en poly(chlorure de vinyle) non plastifi (PVC-U), polypropylne (PE) - Partie 2: Spcifications pour lestubes et raccords avec une surface interne et externe lisseet le systme, de Type AKunststoff-Rohrleitungssysteme fr erdverlegte druckloseAbwasserkanle und -leitungen - Rohrl

11、eitungssysteme mitprofilierter Wandung aus weichmacherfreiemPolyvinylchlorid (PVC-U), Polypropylen (PP) undPolyethylen (PE) - Teil 2: Anforderungen an Rohre undFormstcke mit glatter Innen- und Auenflche und an dasRohrleitnungssystem, Rohrtyp AThis European Standard was approved by CEN on 5 March 200

12、7.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on a

13、pplication to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre

14、 has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Po

15、rtugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means

16、reservedworldwide for CEN national Members.Ref. No. EN 13476-2:2007: EEN 13476-2:2007 (E) 2 Contents Page Foreword. 4 Introduction 5 1 Scope. 6 2 Normative references 6 3 Terms, definitions, symbols and abbreviations .8 3.1 Symbols 8 3.2 Abbreviations 9 4 Material 10 4.1 General . 10 4.2 Unplasticiz

17、ed poly(vinyl chloride) (PVC-U) . 10 4.3 Polypropylene (PP) . 11 4.4 Polyethylene (PE) . 12 4.5 Sealing rings . 14 4.6 Fused or welded joints 14 4.7 Adhesives for PVC-U 14 5 Designation of wall constructions and examples of typical jointing methods . 15 5.1 General . 15 5.2 Wall constructions design

18、ated as Type A. 15 5.3 Designation and design of joints . 16 6 Appearance and colour . 16 7 Geometrical characteristics 16 7.1 General . 16 7.2 Dimensions . 16 7.3 Types of fittings. 22 7.4 Design length of fittings. 22 8 Physical characteristics 22 8.1 Unplasticized poly(vinyl chloride) (PVC-U) . 2

19、2 8.2 Polypropylene (PP) . 23 8.3 Polyethylene (PE) . 24 9 Mechanical characteristics . 25 9.1 Mechanical characteristics of pipes 25 9.2 Mechanical characteristics of fittings 27 10 Performance Requirements 28 11 Marking 30 11.1 General . 30 11.2 Minimum required marking . 30 11.3 Additional markin

20、g 31 Annex A (normative) Virgin PVC-U material 32 Annex B (normative) Utilisation of non-virgin PVC-U material 33 B.1 Reprocessable and recyclable material from pipes and fittings . 33 B.2 External reprocessable and recyclable materials with agreed specifications. 33 B.3 External reprocessable and r

21、ecyclable materials not covered by an agreed specification 34 Annex C (normative) Virgin PP material. 36 EN 13476-2:2007 (E) 3 Annex D (normative) Utilisation of non-virgin PP material .37 D.1 Reprocessable and recyclable material from pipes and fittings 37 D.2 External reprocessable and recyclable

22、materials with an agreed specification 37 D.3 External reprocessable and recyclable materials not covered by an agreed specification.37 Annex E (normative) Virgin PE material38 Annex F (normative) Utilisation of non-virgin PE material .39 F.1 Reprocessable and recyclable material from pipes and fitt

23、ings 39 F.2 External reprocessable and recyclable materials with an agreed specification 39 F.3 External reprocessable and recyclable materials not covered by an agreed specification.39 F.4 External reprocessable and recyclable material from PE rotational-moulded fittings and other components 40 Ann

24、ex G (normative) Impact test at 23 C.41 Annex H (normative) Impact test at 10 C42 Annex I (normative) Ring flexibility test at 20 % diametric deflection .43 Annex J (informative) Survey of possible use of reprocessable and recyclable material 44 National Annex NA (informative) to BS EN 13476-2:20074

25、5 Additional guidance for UK usersEN 13476-2:2007 (E) 4 Foreword This document (EN 13476-2:2007) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national

26、standard, either by publication of an identical text or by endorsement, at the latest by November 2007, and conflicting national standards shall be withdrawn at the latest by November 2007. This standard is a part of a System Standard for plastics piping systems of particular materials for a specifi

27、ed application. There are a number of such System Standards. System Standards are based on the results of the work being undertaken in ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”, which is a Technical Committee of the International Organization for Standardization (I

28、SO). They are supported by separate standards on test methods to which references are made throughout the System Standard. The System Standards are consistent with general standards on functional requirements and on recommended practice for installation. EN 13476 consists of the following Parts unde

29、r the general title Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: General requirements and performance characteristics; Part 2: Specifications f

30、or pipes and fittings with smooth internal and external surface and the system, Type A (this standard); Part 3: Specifications for pipes and fittings with a smooth internal surface and profiled external surface and the system, Type B; Part 4: Assessment of conformity (CEN/TS); Part 5: Guidance for i

31、nstallation (CEN/TS).1For pipes and fittings which have conformed to the relevant national standard before May 2007, as shown by the manufacturer or by a certification body, the national standard may continue to be applied until May 2009. National standards specifically for pipes and fittings for th

32、e transport of surface water are not considered to be conflicting with this standard and may thus be allowed to coexist. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium,

33、 Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. 1The feasibility of this p

34、roject is under study. EN 13476-2:2007 (E) 5 Introduction This standard provides optional choices for impact resistance (see Annex G and Annex H) and ring flexibility, see Annex I. As appropriate, the individual countries may select between those options in their national forewords. EN 13476-2:2007

35、(E) 6 1 Scope This part of EN 13476, together with EN 13476-1, specifies the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are intended to be used for n

36、on-pressure underground drainage and sewerage systems. This part is applicable to pipes and fittings with smooth internal and external surfaces, designated as Type A. It specifies test methods and test parameters as well as requirements. This part is applicable to: a) structured-wall pipes and fitti

37、ngs, which are intended to be used buried underground outside the building structure; reflected in the marking of products by “U”; b) structured-wall pipes and fittings, which are intended to be used buried underground both outside (application area code “U”) and within the building structure (appli

38、cation area code “D”); reflected in the marking of products by “UD”. This part is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints. This part covers a range of pipe and fitting sizes, materials, p

39、ipe constructions, stiffness classes, application classes, and tolerance classes and gives recommendations concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and an

40、y relevant national regulations and installation practices or codes. NOTE 2 For dimensions larger than DN 1200 OD/ID this document may be applied regarding appearance, colour, physical and mechanical characteristics as well as performance requirements. 2 Normative references The following referenced

41、 documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 476, General requirements for components used in discharge pipes, drai

42、ns and sewers for gravity systems EN 580, Plastics piping systems Unplasticized poly(vinyl chloride) (PVC-U) pipes Test method for the resistance to dichloromethane at a specified temperature (DCMT) EN 681-1, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage ap

43、plications Part 1: Vulcanized rubber EN 681-2, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 2: Thermoplastic elastomers EN 681-4, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 4

44、: Cast polyurethane sealing elements EN 727, Plastics piping and ducting systems Thermoplastics pipes and fittings Determination of Vicat softening temperature (VST) EN 728, Plastics piping and ducting systems Polyolefin pipes and fittings Determination of oxidation induction time EN 13476-2:2007 (E

45、) 7 EN 744, Plastics piping and ducting systems Thermoplastics pipes Test method for resistance to external blows by the round-the-clock method EN 922, Plastics piping and ducting systems Pipes and fittings of unplasticized poly(vinyl chloride) (PVC-U) Specimen preparation for determination of the v

46、iscosity number and calculation of the K-value EN 1053, Plastics piping systems Thermoplastics piping systems for non-pressure applications Test method for watertightness EN 1055:1996, Plastics piping systems Thermoplastics piping systems for soil and waste discharge inside buildings Test method for

47、 resistance to elevated temperature cycling EN 1277, Plastics piping systems Thermoplastics piping systems for buried non-pressure applications Test methods for leaktightness of elastomeric sealing ring type joints EN 1401-1, Plastics piping systems for non-pressure underground drainage and sewerage

48、 Unplasticized poly(vinyl chloride) (PVC-U) Part 1: Specifications for pipes, fittings and the system EN 1411, Plastics piping and ducting systems Thermoplastics pipes Determination of resistance to external blows by the staircase method EN 1437, Plastics piping systems Piping systems for undergroun

49、d drainage and sewerage Test method for resistance to combined temperature cycling and external loading EN 1446, Plastics piping and ducting systems Thermoplastics pipes Determination of ring flexibility EN 1852-1, Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene (PP) Part 1: Specifications for pipes, fittings and the system EN 1905, Plastics piping systems Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material Method for asses