EN 13523-16-2004 en Coil coated metals - Test methods - Part 16 Resistance to abrasion《卷材覆层金属的试验方法 第16部分 耐磨性》.pdf

1、BRITISH STANDARD BS EN 13523-16:2004 Coil coated metals Test methods Part 16: Resistance to abrasion The European Standard EN 13523-16:2004 has the status of a British Standard ICS 25.220.60 BS EN 13523-16:2004 This British Standard was published under the authority of the Standards Policy and Strat

2、egy Committee on 25 November 2004 BSI 25 November 2004 ISBN 0 580 44864 9 National foreword This British Standard is the official English language version of EN 13523-16:2004. The UK participation in its preparation was entrusted to Technical Committee STI/27, Paint systems for metallic substrates,

3、which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the s

4、ection entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application

5、. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor

6、related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the

7、 document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN1352316 November2004 ICS25.220.60 Englishversion CoilcoatedmetalsTestmethodsPart16:Resistanceto abrasion TlesprlaquesMthodesdessaiPartie16: Rsistancelabrasion Bandbes

8、chichteteMetallePrfverfahrenTeil16: WiderstandsfhigkeitgegenAbrieb ThisEuropeanStandardwasapprovedbyCENon23September2004. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodate

9、listsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlangu

10、ageandnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portuga

11、l, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2004CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref

12、.No.EN1352316:2004:EEN 13523-16:2004 (E) 2 Foreword This document (EN 13523-16:2004) has been prepared by Technical Committee CEN/TC 139 “Paints and varnishes”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of

13、an identical text or by endorsement, at the latest by May 2005, and conflicting national standards shall be withdrawn at the latest by May 2005. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Sta

14、ndard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 13523-16:2004 (E)

15、3 1 Scope This part of EN 13523 describes the procedure for determining the resistance to abrasion and wear of an organic coating on a metallic substrate. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the

16、edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13523-0:2001, Coil coated metals Test methods Part 0: General introduction and list of test methods. EN 23270, Paints and varnishes and their raw materials Temperatures

17、 and humidities for conditioning and testing (ISO 3270:1984). ISO 7784-2, Paints and varnishes Determination of resistance to abrasion Part 2: Rotating abrasive rubber wheel method. 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13523-0:2001 apply. 4

18、 Principle A coated test panel is placed on a rotating disc under a set of two abrasive wheels mounted in parallel and symmetrically on opposite sides of the centre rotating in the reverse direction. 5 Apparatus 5.1 Taber abraser, as specified in ISO 7784-2, or equivalent equipment. 5.2 Analytical b

19、alance, accurate to 0,1 mg. 5.3 Suction device, with two nozzles. One of the nozzles shall be positioned between the two wheels and the other placed diametrically opposite the first. The distance between the axes of the two nozzles shall be (75 2) mm and the distance between them and the test panel

20、1 mm to 2 mm. When the suction nozzles are in position, the air pressure in the suction device shall be 1,5 kPa to 1,6 kPa lower than the atmospheric pressure. 6 Sampling See EN 13523-0. EN 13523-16:2004 (E) 4 7 Test panels See EN 13523-0. Cut three test panels to approximately 100 mm 100 mm with a

21、hole drilled in the centre, appropriate for the apparatus being used. The test panels shall be flat and free from any edge burr to avoid any deformation of the test panels. 8 Procedure 8.1 Test conditions Measure the resistance to abrasion of the organic coating at ambient conditions. For more accur

22、ate measurements, as required for instance in case of dispute, the temperature shall be (23 2) C and the relative humidity (50 5) %, in accordance with EN 23270. 8.2 Determination First determine the mass of each test panel to be tested, using an analytical balance (5.2). Place the test panel on the

23、 panel holder, coated side to be tested facing up, and fix it using a screw. Prepare the two abrading arms with cleaned abrasive wheels, e.g. type CS 10 or the more abrasive CS 17 (see ASTM D 4060-01), and additional masses to make the total load typically 500 g or 1000 g. Place the arms on the test

24、 panel and start the abrader (speed fixed; typically 60 rpm, maximum 100 rpm) for a specified number of revolutions or until the substrate is exposed. A suction device continuously removes the debris from the test panel. The test can be interrupted after 250, 500, 1000 or more revolutions. If the su

25、bstrate is exposed, the test shall be stopped and no mass measurement is required. Otherwise the test panel is re-weighed. The loss of material i.e. difference in mass, in combination with the number of revolutions is a measure of the abrasion resistance. The wheels shall be cleaned after every 1000

26、 revolutions in a continuous test or before every new test, using a fresh refacing disc for 25 revolutions. Repeat the procedure for two further test panels. 9 Expression of results The result shall be expressed either by the mean of the mass loss after every specified number of revolutions or the m

27、ean of the number of revolutions until the substrate is just exposed. 10 Precision No precision data are available EN 13523-16:2004 (E) 5 11 Test report The test report shall contain at least the following information: a) all details necessary to identify the product tested; b) a reference to this p

28、art of EN 13523 (EN 13523-16); c) the total mass of the abrading arms; d) the type of wheels used; e) the result of the test, as indicated in clause 9; f) any deviation from the test method specified; g) the date of the test. EN 13523-16:2004 (E) 6 Bibliography EN 1396, Aluminium and aluminium alloy

29、s Coil coated sheet and strip for general applications Specifications. EN 10169-1, Continuously organic coated (coil coated) steel flat products Part 1: General information (definitions, materials, tolerances, test methods). ENV 10169-2, Continuously organic coated (coil coated) steel flat products

30、Part 2: Products for building exterior applications. EN 10169-3, Continuously organic coated (coil coated) steel flat products Part 3: Products for building interior applications. ASTM D 4060-01, Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser. ISO 7784-1, Paint

31、s and varnishes Determination of resistance to abrasion Part 1: Rotating abrasive-paper- covered wheel method. ISO 7784-3, Paints and varnishes Determination of resistance to abrasion Part 3: Reciprocating test panel method. blankBS EN 13523-16:2004 BSI 389 Chiswick High Road London W4 4AL BSI Briti

32、sh Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of Br

33、itish Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of t

34、he technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. B

35、uying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for interna

36、tional standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Tech

37、nical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date wit

38、h standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standard

39、s via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodie

40、s. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free u

41、se, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.