EN 13523-29-2010 6875 Coil coated metals - Test methods - Part 29 Resistance to environmental soiling (Dirt pick-up and striping)《卷材覆层金属的试验方法 第29部分 耐环境污染(粘污性和剥落)》.pdf

1、BS EN13523-29:2010ICS 25.220.60NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDCoil coated metals Test methodsPart 29: Resistance to environmentalsoiling (Dirt pick-up and striping)Copyright European Committee for Standardization Provided by IHS under license wi

2、th CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 30 June2010 BSI 2010ISBN 978 0 580 64389 7Amendments/corrigenda issued since publicationDate CommentsBS EN 13

3、523-29:2010National forewordThis British Standard is the UK implementation of EN 13523-29:2010.The UK participation in its preparation was entrusted to TechnicalCommittee STI/27, Paint systems for metallic substrates.A list of organizations represented on this committee can be obtained onrequest to

4、its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Copyright European Committee for Standardization Provided by IHS und

5、er license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 13523-29:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13523-29 March 2010 ICS 25.220.60 English Version Coil coated metals - Test methods - Part 29: Resistance to environmental soi

6、ling (Dirt pick-up and striping) Tles prlaques - Mthodes dessai - Partie 29 : Rsistance la pollution environnementale (salissures) Bandbeschichtete Metalle - Prfverfahren - Teil 29: Bestndigkeit gegen Verschmutzung (Schmutzaufnahme und Streifenbildung) This European Standard was approved by CEN on 2

7、0 February 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may

8、 be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CE

9、N Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

10、Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploita

11、tion in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13523-29:2010: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 13523-29:2010EN 1

12、3523-29:2010 (E) 2 Contents Page Foreword 31 Scope 52 Normative references 53 Terms and definitions .54 Principle 55 Apparatus and materials .56 Sample preparation .77 Procedure .78 Evaluation .79 Test report 9Bibliography . 10Copyright European Committee for Standardization Provided by IHS under li

13、cense with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 13523-29:2010EN 13523-29:2010 (E) 3 Foreword This document (EN 13523-29:2010) has been prepared by Technical Committee CEN/TC 139 “Paints and varnishes”, the secretariat of which is held by DIN. Th

14、is European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2010, and conflicting national standards shall be withdrawn at the latest by September 2010. Attention is drawn to the possibility that some

15、 of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. EN 13523, Coil coated metals Test methods, consists of the following parts: Part 0: General introduction and list of test methods Par

16、t 1: Film thickness Part 2: Specular gloss Part 3: Colour difference Instrumental comparison Part 4: Pencil hardness Part 5: Resistance to rapid deformation (impact test) Part 6: Adhesion after indentation (cupping test) Part 7: Resistance to cracking on bending (T-bend test) Part 8: Resistance to s

17、alt spray (fog) Part 9: Resistance to water immersion Part 10: Resistance to fluorescent UV radiation and water condensation Part 11: Resistance to solvents (rubbing test) Part 12: Resistance to scratching Part 13: Resistance to accelerated ageing by the use of heat Part 14: Chalking (Helmen method)

18、 Part 15: Metamerism Part 16: Resistance to abrasion Part 17: Adhesion of strippable films Part 18: Resistance to staining Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 1

19、3523-29:2010EN 13523-29:2010 (E) 4 Part 19: Panel design and method of atmospheric exposure testing Part 20: Foam adhesion Part 21: Evaluation of outdoor exposed panels Part 22: Colour difference Visual comparison Part 23: Colour stability in humid atmospheres containing sulfur dioxide Part 24: Resi

20、stance to blocking and pressure marking Part 25: Resistance to humidity Part 26: Resistance to condensation of water Part 27: Resistance to humid poultice (Cataplasm test) Part 29: Resistance to environmental soiling (Dirt pick-up and striping) According to the CEN/CENELEC Internal Regulations, the

21、national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherla

22、nds, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 13523-29:2010

23、EN 13523-29:2010 (E) 5 1 Scope This European Standard specifies a procedure for the comparative evaluation of resistance to soiling of an organic coating on a metallic substrate (coil coating) in an outdoor exposure environment, particularly the soiling defect known as “Tiger stripes“. 2 Normative r

24、eferences The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13523-0:2001, Coil coated metals Tes

25、t methods Part 0: General introduction and list of test methods EN 13523-19:2004, Coil coated metals Test methods Part 19: Panel design and method of atmospheric exposure testing 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13523-0:2001 apply. 4 Pr

26、inciple A test panel is exposed along with known reference panels, to the effects of atmospheric dirt and rain. The dirt and rain is collected and directed onto the surface of the panels in such a way as to channel rainwater thus creating the conditions to form stripes on the surface under test. 5 A

27、pparatus and materials 5.1 Existing EN 13523-19 exposure rack design (see EN 13523-19:2004, Clause 4 and Figure 4) modified as described below. The area of the rack normally used for the exposure of panels to the 5 orientation is used to install a sheet made of UV stable polymeric material (e.g. pol

28、ycarbonate). This sheet forms the collector of the atmospheric soil and is angled on the upper surface of the rack at between 10 and 12 with respect to the horizontal plane to control the rate of run-off of rainwater. The machining imparts grooves of 3 mm width and 3 mm depth at a separation of 3 mm

29、 extending along the surface and over the rounded edge to direct rainwater onto the panels in rivulets (see Figures 1 and 2). The upper row of the 90 North facing exposure area of the rack is used to fix the panels, having removed the existing overhang. Two rows are used for this exposure if the pan

30、els are longer than 200 mm. The test panels are positioned so that the top edge is in uniform contact with the bottom edge of the collector overhang. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without l

31、icense from IHS-,-,-BS EN 13523-29:2010EN 13523-29:2010 (E) 6 Figure 1 Detail of grooves to be machined Top view Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 13523-29:20

32、10EN 13523-29:2010 (E) 7 Figure 2 Detail of grooves to be machined Side view 6 Sample preparation The test samples shall be flat and free from contamination. Sampling shall be performed according to EN 13523-0. Sample dimensions shall be 100 mm (200 mm to 400 mm). If coil production line samples are

33、 used these should be cut so as to have the longest dimension in the direction of rolling. 7 Procedure In addition to the test panel, expose two reference panels for each test campaign: one of known good and one of known poor performance. This allows for comparative evaluation in various atmospheric

34、 conditions. The duration of the test is typically three months and shall be no longer than six months to avoid other weathering effects, e.g. corrosion, photo degradation, etc. At the end of the test period there shall be sufficient separation in performance between the reference panels so as to al

35、low a ranking of the test panels. If not the test will be restarted with new panels. 8 Evaluation Evaluate all panels as soon as possible after the exposure; intermediate examinations may be made (visual observations of the panels on the exposure rack). Copyright European Committee for Standardizati

36、on Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 13523-29:2010EN 13523-29:2010 (E) 8 During handling of the panels and storage before examination, care shall be taken not to disturb the dirt on the surface. Then the tes

37、t panels are compared to the reference panels and classified relative to each other and to reference panels and ranked accordingly, e.g.: better than the best reference panel; same as the best reference panel; in between of both reference panels; same as the worst reference panel; worse than the wor

38、st reference panel. Changes in gloss and colour measured in accordance with EN 13523-2 and EN 13523-3 can be used to make the comparison. Record gloss and colour at points A, B and C (triplicate readings), as indicated in Figure 3. The results should be documented by photographing the panels. To eva

39、luate the ease with which the panels can be cleaned, they may then be subjected to a washing procedure, implementing the procedure described in EN 13523-21:2003, 8.2.2: Wash the area indicated in Figure 3 with water containing 0,5 % by mass of a mild non-reactive detergent (pH 6 to pH 7) at ambient

40、temperature. Use a cloth or sponge that is non-abrasive and smooth to gently clean the surface. Rinse with water at ambient temperature and air dry at ambient temperature. A first evaluation is made by comparing the washed area of each panel with the unwashed area; the second evaluation is made by r

41、e-ranking the washed areas as above. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 13523-29:2010EN 13523-29:2010 (E) 9 Dimensions in millimetres Key 1 direction of dirt/w

42、ater 2 line for wash test 3, 4, 5 measuring points (triplicate reading) Figure 3 Dirt panel inspection 9 Test report The test report shall contain at least the following information: a) all details necessary to identify the product tested; b) reference to this European Standard (EN 13523-29); c) all

43、 details necessary to identify the references; d) geographical location of the rack; e) test duration; f) results of the test, as indicated in Clause 8; g) any deviation from the test procedure described; h) date(s) of the test. Copyright European Committee for Standardization Provided by IHS under

44、license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 13523-29:2010EN 13523-29:2010 (E) 10 Bibliography 1 EN 1396, Aluminium and aluminium alloys Coil coated sheet and strip for general applications Specifications 2 EN 10169-1, Continuously organic

45、coated (coil coated) steel flat products Part 1: General information (definitions, materials, tolerances, test methods) 3 EN 10169-2, Continuously organic coated (coil coated) steel flat products Part 2: Products for building exterior applications 4 EN 10169-3, Continuously organic coated (coil coat

46、ed) steel flat products Part 3: Products for building interior applications 5 EN 13523-2, Coil coated metals Test methods Part 2: Specular gloss 6 EN 13523-3, Coil coated metals Test methods Part 3: Colour difference Instrumental comparison 7 EN 13523-21:2003, Coil coated metals Test methods Part 21

47、: Evaluation of outdoor exposed panels Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 13523-29:2010This page has been intentionally left blankCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN13523-29:2010BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards Institu