EN 13553-2017 en Resilient floor coverings - Polyvinyl chloride floor coverings for use in special wet areas - Specification.pdf

1、Resilient floor coverings - Polyvinyl chloride floor coverings for use in special wet areas - SpecificationBS EN 13553:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13553 August 2017 ICS 97.150 Supersedes EN

2、13553:2015English Version Resilient floor coverings - Polyvinyl chloride floor coverings for use in special wet areas - Specification Revtements de sol rsilients - Revtements de sol base de polychlorure de vinyle pour zones humides spciales - Spcification Elastische Bodenbelge - Polyvinylchlorid-Bod

3、enbelge zur Anwendung in besonderen Nassrumen - Spezifikation This European Standard was approved by CEN on 22 May 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard withou

4、t any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other la

5、nguage made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denm

6、ark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN C

7、OMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13553:2017 ENational f

8、orewordThis British Standard is the UK implementation of EN 13553:2017. It supersedes BS EN 13553:2015, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/60, Resilient and Laminate Floor Coverings.A list of organizations represented on this committee

9、 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 94044 6ICS 97.150Compl

10、iance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 13553:2017EURO

11、PEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13553 August 2017 ICS 97.150 Supersedes EN 13553:2015English Version Resilient floor coverings - Polyvinyl chloride floor coverings for use in special wet areas - Specification Revtements de sol rsilients - Revtements de sol base de polychlorure de vi

12、nyle pour zones humides spciales - Spcification Elastische Bodenbelge - Polyvinylchlorid-Bodenbelge zur Anwendung in besonderen Nassrumen - Spezifikation This European Standard was approved by CEN on 22 May 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipula

13、te the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Sta

14、ndard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the na

15、tional standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, S

16、erbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and

17、by any means reserved worldwide for CEN national Members. Ref. No. EN 13553:2017 EBS EN 13553:2017EN 13553:2017 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Requirements . 5 4.1 General requirements . 5 4.2 Additional performance requirem

18、ents . 5 4.3 Installation 5 5 Marking . 6 Annex A (normative) Water tightness test 7 A.1 Scope 7 A.2 Apparatus . 7 A.3 Test specimen . 7 A.4 Conditioning 8 A.5 Testing . 8 A.6 Test report . 9 Annex B (informative) Choice of floor covering category. 10 Annex C (informative) Installation . 11 Annex D

19、(informative) Determination of elongation at break (optional property) . 12 D.1 Apparatus, sampling and preparation of test pieces 12 D.2 Procedure 12 D.3 Calculation and expression of result . 12 D.4 Requirement 12 D.5 Test report 12 BS EN 13553:2017EN 13553:2017 (E) 3 European foreword This docume

20、nt (EN 13553:2017) has been prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at

21、 the latest by February 2018, and conflicting national standards shall be withdrawn at the latest by February 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such

22、patent rights. This document supersedes EN 13553:2015. The main changes in this revision relate to including the reference to EN 13845 in the scope and relevant parts of the standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries a

23、re bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, P

24、ortugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 13553:2017EN 13553:2017 (E) 4 1 Scope This European standard specifies the minimum additional characteristics which are necessary for: polyvinyl chloride floor coverings in roll form accord

25、ing to EN ISO 10581 or EN ISO 10582, polyvinyl chloride floor coverings with foam backing in roll form to EN 651, polyvinyl chloride floor coverings with particle based enhanced slip resistance in roll form to EN 13845 to be installed satisfactorily in special wet areas to form a watertight installa

26、tion with a long life. It specifies two categories (A and B) for use on different substrates. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited appli

27、es. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 651, Resilient floor coverings Polyvinyl chloride floor coverings with foam layer Specification EN 661, Resilient floor coverings Determination of the spreading of water EN 684, Resilient

28、 floor coverings Determination of seam strength EN 12466, Resilient floor coverings Vocabulary EN 13845, Resilient floor coverings Polyvinyl chloride floor coverings with particle based enhanced slip resistance Specification EN ISO 10581, Resilient floor coverings Homogeneous poly(vinyl chloride) fl

29、oor covering Specifications (ISO 10581) EN ISO 10582, Resilient floor coverings Heterogeneous poly(vinyl chloride) floor coverings Specification (ISO 10582) EN ISO 24340, Resilient floor coverings Determination of thickness of layers (ISO 24340) EN ISO 24344, Resilient floor coverings Determination

30、of flexibility and deflection (ISO 24344) EN ISO 24346, Resilient floor coverings Determination of overall thickness (ISO 24346) 3 Terms and definitions For the purposes of this document, the terms and definitions of EN 12466 and the following apply. 3.1 special wet area area where floors are design

31、ed to be frequently or permanently wet and equipped with floor based drainage systems, for example trapped floor gullies EXAMPLE Bathrooms with free-standing tubs and shower rooms without partitions. BS EN 13553:2017EN 13553:2017 (E) 5 4 Requirements 4.1 General requirements Products covered by this

32、 standard shall conform to the requirements of EN ISO 10581, EN ISO 10582, EN 651 or EN 13845. 4.2 Additional performance requirements Floor coverings conforming to the requirements of EN ISO 10581, EN ISO 10582, EN 651 or EN 13845 are suitable for special wet areas when they meet the additional req

33、uirements specified in Table 1. Table 1 Products suitable for special wet areas Characteristic Identity code W1 Identity code W2 Identity code W3 Test method Floor covering type a)Floor coverings conforming to EN ISO 10581, EN ISO 10582 or EN 13845 Floor coverings conforming to EN ISO 10581, EN ISO

34、10582 or EN 13845 Floor coverings conforming to EN 651 - Substrate type b)Category A Category B Category A - Nominal overall thickness (in mm) 1,5 2,0 - EN ISO 24346 Total thickness of compact layers (in mm) as for overall thickness as for overall thickness 1,0 EN ISO 24340 Spreading of water (in da

35、ys) - - 7 EN 661 Seam strength, when welded in accordance with the manufacturers instructions (in N/50 mm) 240 400 240 EN 684 Flexibility When bent around a mandrel of 10 mm diameter, no cracking or other surface deterioration shall be visible with the naked eye For heterogeneous materials the test

36、shall be made with the surface side as well as with the reverse side outwards. EN ISO 24344 Water tightness The welded product shall be classified watertight. Annex A aFor installation see Annex C. bFor choice of category see Annex B. 4.3 Installation See Annex C. BS EN 13553:2017EN 13553:2017 (E) 6

37、 5 Marking Floor coverings covered by this standard and/or their packaging shall bear the following marking in addition to the marking according to EN ISO 10581, EN ISO 10582, EN 651 or EN 13845: a) number and year of publication of this European Standard (EN 13553:2017); b) identity code W1, W2 or

38、W3; c) category A or B. BS EN 13553:2017EN 13553:2017 (E) 7 Annex A (normative) Water tightness test A.1 Scope This annex describes a method for testing the water tightness of floor coverings. A.2 Apparatus A.2.1 A base of non-porous material such as metal or glass, on which the sample rests during

39、testing. NOTE If the base is transparent and suitably supported, it will enable any leakage to be observed from below. A.2.2 A watertight, bottomless box-frame, to be placed on top of the test specimen. The box-frame shall have vertical sides at least 300 mm and shall cover a surface area of at leas

40、t 300 mm x 500 mm. The box-frame will be supporting water pressure and should therefore be held in place by clamps or weights. The box-frame shall be sealed to achieve water tightness between the floor covering and the box-frame. A.2.3 Indicator paper, sensitive to moisture. A.3 Test specimen The te

41、st specimen shall be flat or capable of being flattened so that it lies flat on the base. The base may be covered by polyethylene foil or similar material. When preparing test specimens the manufacturers instructions shall be observed. The size of the specimen shall be at least 500 mm x 800 mm and i

42、t shall be provided with seams welded in accordance with manufacturers recommendations (see Figure A.1). BS EN 13553:2017EN 13553:2017 (E) 8 Dimensions in millimetres Key 1 welded seam Figure A.1 Specimen with welded seams A.4 Conditioning Special conditioning is not required. The test specimen shal

43、l be dry on visual inspection and be at a temperature of 15 C to 25 C. A.5 Testing The temperature of the water during testing shall be 15 C to 25 C. Cover the supporting base with the indicator paper. Place the test specimen on the indicator paper with the use surface upwards. Place the box-frame o

44、ver the test specimen and press the support towards the box-frame to ensure water tightness (see A.2 and Figure A.2). Fill the box-frame with water to a level of 200 mm 10 mm above the upper surface of the test specimen. This water level is maintained for 24 h 1 h after which the water is drained of

45、f. The moisture indicator and the test specimen are examined for any signs of water penetrating the specimen. The test specimen is considered watertight if there is no sign of penetrating water. BS EN 13553:2017EN 13553:2017 (E) 9 Dimensions in millimetres Key 1 position of box-frame on specimen Fig

46、ure A.2 Position of box-frame on specimen A.6 Test report The test report shall contain the following information: a) reference to this method i.e. EN 13553:2017, Annex A; b) the material tested (type, source, colour and manufacturers reference numbers); c) preparation of the sample for testing; d)

47、result of inspection according to A.5. BS EN 13553:2017EN 13553:2017 (E) 10 Annex B (informative) Choice of floor covering category The choice of category should be made according to national codes of practice. If a code of practice does not exist the criteria of choice should be the following: Cate

48、gory A: For use on all substrates where traffic intensity or risk of mechanical damage is normal. Category B: For use on all substrates where traffic intensity or risk of mechanical damage is higher than normal. BS EN 13553:2017EN 13553:2017 (E) 11 Annex C (informative) Installation Products accordi

49、ng to this standard should be installed according to manufacturers instructions for wet area installation for the product, and any national codes of practice. The installations should be carried out by an installer skilled in wet area installations and in a manner that ensures a correct installation. BS EN 13553:2017EN 13553:2017 (E) 12 Annex D (informative) Determination of elongation at break (optional property) D.1 Apparatus, sampling and preparation of test pieces As specified in E