EN 13565-1-2003 en Fixed firefighting systems - Foam systems - Part 1 Requirements and test methods for components (Incorporates Amendment A1 2007)《固定式消防系统 泡沫设备 第1部分 组件的要求和试验方法 包含修.pdf

1、BRITISH STANDARDBS EN 13565-1:2003 +A1:2007Fixed firefighting systems Foam systems Part 1: Requirements and test methods for componentsICS 13.220.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39

2、g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 13565-1:2003+A1:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 11 February 2004 BSI 2008ISBN 978 0 580 63713 1National forewordThis British Standard is the UK implementation of EN 135

3、65-1:2003+A1:2007. It supersedes BS EN 13565-1:2003 which is withdrawn. The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indica

4、ted by !“.The UK participation in its preparation was entrusted by Technical Committee FSH/18, Fixed fire fighting systems, to Subcommittee FSH/18/7, Foam systems. A list of organizations represented on this subcommittee can be obtained on request to its secretary.This publication does not purport t

5、o include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate Comments30 September 2008 Implementation of CEN amendment A1:200

6、7EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13565-1:2003+A1 October 2007 ICS 13.220.20 Supersedes EN 13565-1:2003 English Version Fixed firefighting systems - Foam systems - Part 1: Requirements and test methods for components Installations fixes de lutte contre lincendie - Systmes mulseur

7、s - Partie 1: Exigences et mthodes dessai relatives aux composants Ortsfeste Brandbekmpfungsanlagen - Schaumlschanlagen - Teil 1: Anforderungen und Prfverfahren fr Bauteile This European Standard was approved by CEN on 21 November 2003 and includes Amendment 1 approved by CEN on 13 September 2007. C

8、EN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on ap

9、plication to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centr

10、e has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland

11、, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by a

12、ny means reserved worldwide for CEN national Members. Ref. No. EN 13565-1:2003+A1:2007: EEN 13565-1:2003+A1:2007 (E) 2 Contents page Foreword4 Introduction .5 1 Scope 6 2 Normative references 6 3 Terms and definitions .7 4 General construction requirements.9 4.1 Connections .9 4.2 Parts intended for

13、 removal during routine field maintenance 10 4.3 Hydrostatic strength10 4.4 Castings10 4.5 Corrosion resistance of metal parts 10 4.6 Elastomeric joint rings 11 4.7 Plastics and reinforced resin materials.11 4.8 Heat and fire resistance 12 5 Discharge coefficients and characteristics of branchpipes,

14、 sprayers and low and high back-pressure foam generators 12 5.1 Single orifice components12 5.2 Multiple orifice components.12 6 Quality of foam from aspirating components.12 6.1 Low and medium expansion components 12 6.2 High expansion components13 7 Accuracy of proportioning components .13 8 Compo

15、nents for low expansion foam systems 13 8.1 Foam branchpipes (hand and monitor).13 8.2 Foam sprayers .13 8.3 Foam pourers and foam chambers13 8.4 Vapour seals.13 8.5 Low back-pressure and high back-pressure foam generators.14 8.6 Semi-subsurface hose units.14 9 Components for medium and high expansi

16、on foam systems 14 9.1 Nozzles and sprayers 14 9.2 High expansion foam generators.14 10 Tanks and pressure vessels for foam concentrates or solutions 14 10.1 General14 10.2 Tanks at atmospheric pressure15 10.3 Pressure vessels15 11 Marking .15 12 Evaluation of conformity.15 12.1 General15 12.2 Initi

17、al type testing 16 12.3 Factory production control (FPC) 17 Annex A (normative) Hydrostatic test.19 Annex B (normative) Ageing test for plastics and reinforced resin materials .20 B.1 General20 B.2 Tensile strength and elongation test.20 B.3 Impact test 20 BS EN 13565-1:2003+A1:2007EN 13565-1:2003+A

18、1:2007 (E) 3 Annex C (normative) Liquid exposure test.21 Annex D (normative) Heat and fire resistance test for foam generators 22 Annex E (normative) Flow tests 23 E.1 General23 E.2 Discharge coefficient 23 E.3 Discharge characteristic.23 Annex F (normative) Quality of foam from aspirating component

19、s 24 F.1 General24 F.2 Low expansion foams .24 F.3 Medium expansion foams.24 F.4 High expansion foams 24 Annex G (normative) High expansion foam generator test25 Annex H (normative) Range tests for branchpipes (hand and monitor) .26 Annex I (normative) Area coverage test for foam sprayers and nozzle

20、s 27 Annex J (normative) Maximum flow and back pressure.28 J.1 General28 J.2 Maximum flow 28 J.3 Back pressure 28 Annex K (normative) Insertion and deployment of semi-subsurface hose 29 BS EN 13565-1:2003+A1:2007EN 13565-1:2003+A1:2007 (E) 4 Foreword This document (EN 13565-1:2003+A1:2007) has been

21、prepared by Technical Committee CEN /TC 191, “Fixed firefighting systems“ the secretariat of which is held by BSI. This document shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2008 and conflicting national standa

22、rds shall be withdrawn at the latest by April 2008. This document includes Amendment 1, approved by CEN on 2007-09-13. This document supersedes EN 13565-1:2003. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! “. !deleted text“ According to the CEN/C

23、ENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lux

24、embourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 13565-1:2003+A1:2007EN 13565-1:2003+A1:2007 (E) 5 Introduction This European Standard covers components intended for use in fixed fire fighting foam systems. BS EN

25、 13565-1:2003+A1:2007EN 13565-1:2003+A1:2007 (E) 6 1 Scope This European Standard specifies requirements for materials, construction, and performance of components intended for use in fixed foam fire fighting systems, and using foam concentrates conforming to EN 1568-1 to EN 1568-4. The components c

26、overed are: proportioners, sprayers, semi-subsurface hose units, branchpipes, low/medium expansion foam generators, high expansion foam generators, foam chambers, tanks and pressure vessels. Methods of test are given in annexes A to K. Requirements are also given for the provision of the characteris

27、tic data needed for correct application of components. NOTE 1 Unless otherwise stated pressures are gauge pressures expressed in bar. The requirements of this specification do not cover, except where stated, the use of combinations of components to form part, or the whole, of a fire fighting system.

28、 NOTE 2 It should not be assumed that components conforming to this specification are necessarily compatible one with another. Requirements for pumps, motors and the functioning of mechanical components (i.e. remote control turrets) are outside the scope of this standard. 2 Normative references This

29、 European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publica

30、tions apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 671-1:2001, Fixed firefighting systems - Hose systems - Part 1: Hose reels with semi-rigid hose EN

31、1568-1: 2000, Fire extinguishing media - Foam concentrates - Part 1: Specification for medium expansion foam concentrates for surface application to water-immiscible liquids EN 1568-2:2000, Fire extinguishing media - Foam concentrates - Part 2: Specification for high expansion foam concentrates for

32、surface application to water-immiscible liquids EN 1568-3:2000, Fire extinguishing media - Foam concentrates - Part 3 Specification for low expansion foam concentrates for surface application to water-immiscible liquids EN 1568-4, Fire extinguishing media - Foam concentrates - Part 4: Specification

33、for low expansion foam concentrates for surface application to water-miscible liquids !EN 12259-1:1999+A1:2001“, Fixed fire fighting systems Components for sprinkler and water spray systems - Part 1: Sprinklers EN 12416-1:2001, Fixed firefighting systems - Powder systems - Part 1: Requirements and t

34、est methods for components EN 12542, Static welded steel cylindrical tanks, serially produced for the storage of Liquified Petroleum Gas (LPG) having a volume not greater than 13 m3and for installation above ground - Design and manufacture EN 20225, Fasteners - Bolts, screws, studs and nuts Symbols,

35、 designations and dimensions (ISO 225:1983) EN ISO 175, Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:1999) BS EN 13565-1:2003+A1:2007EN 13565-1:2003+A1:2007 (E) 7 EN ISO 179-1, Plastics - Determination of Charpy impact properties - Part 1:

36、 Non-instrumented impact test (ISO 179-1:2000) EN ISO 180, Plastics - Determination of Izod impact strength (ISO 180:2000) EN ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) EN ISO 527-1, Plastics - Det

37、ermination of tensile properties - Part 1: General principles (ISO 527-1:1993 including Corr 1:1994) EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs (ISO 898-1:1999) EN ISO 4759-1, Tolerances for fasteners - Part 1: Bolts, screw

38、s, studs and nuts - Product grades A, B and C (ISO 4759-1:2000) EN ISO 9001:2000 Quality management systems Requirements (ISO 9001:2000) ISO 7-1, Pipe threads where pressure-tight joints are made on the threads - Part 1: Dimensions, tolerances and designation ISO 272, Fasteners - Hexagon products -

39、Widths across flats ISO 885, General purpose bolts and screws - Metric series - Radii under the head ISO 888, Bolts screws and studs - Nominal lengths and thread length for general purpose bolts ISO 1179-1, Connections for general use and fluid power - Ports and stud ends with EN ISO 228-1 threads w

40、ith elastomeric or metal-to-metal sealing - Part 1: Threaded ports (Revision of ISO 1179:1981) ISO 4633, Rubber seals - Joint rings for water supply, drainage and sewerage pipelines - Specification for material ISO 6447, Rubber seals - Joint rings used for gas supply pipes and fittings - Specificati

41、on for material ISO 6448, Rubber seals - Joint rings used for petroleum product supply pipes and fittings - Specification for material ISO 7005-1, Metallic flanges; Part 1: Steel flanges ISO 7005-2, Metallic flanges; Part 2: Cast iron flanges ISO 9227, Corrosion tests in artificial atmospheres; salt

42、 spray tests Nordtest method NT Fire 042 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply. 3.1 aspirating component component within which air and foam solution are mixed to make foam 3.2 branchpipe component which projects foam in the for

43、m of a jet or spray BS EN 13565-1:2003+A1:2007EN 13565-1:2003+A1:2007 (E) 8 3.3 component item or piece of equipment intended for use in a fixed foam fire extinguishing system 3.4 discharge coefficient (K factor) K factor for the equation Q = KdP where Q is the flow rate through the component in l/m

44、in and dp is the inlet pressure in bar 3.5 high back pressure foam generator component which introduces air into the foam solution stream for delivery against a high back pressure, for example, as is found in tank sub-surface injection 3.6 high expansion foam foam which has an expansion ratio greate

45、r than 200 3.7 foam generator component which introduces air into the foam solution stream for delivery against a low back pressure, i.e. discharging against atmospheric pressure 3.8 low expansion foam foam which has an expansion ratio not greater than 20 3.9 foam chamber component that incorporates

46、 a vapour seal, a foam expansion chamber, and which delivers foam into a flammable or combustible liquid storage tank. A foam generator may be connected to the foam chamber inlet 3.10 medium expansion foam foam which has an expansion ratio greater than 20 but not greater than 200 3.11 monitor compon

47、ent consisting of a branchpipe and turret 3.12 non-aspirating components components which discharge a spray of foam solution so that mixing with air and formation of foam takes place outside the component 3.13 fixed foam pourer (foam discharge outlet) component which discharges foam onto the interna

48、l wall of a tank NOTE Some pourers are designed to discharge the foam tangentially in order to create a circular motion, and thus promote foam distribution. 3.14 proportioning component component which controls the mixing of foam concentrate into a water flow, at a predetermined ratio, to produce a

49、foam solution NOTE Proportioning components are variously described as inline, bypass and round the pump inductors, injectors, eductors, proportioners, venturis, constant and variable flow valves, orifice plates, water powered foam pumps and displacement proportioners. BS EN 13565-1:2003+A1:2007EN 13565-1:2003+A1:2007 (E) 9 3.15 semi-subsurface hose unit component which delivers foam below the surface of a flammable liquid so that it rises to the liquid surface within a flexible hose and spreads over the liquid surface 3.16 sprayer open nozzle which discharges