EN 13865-2017 en Surfaces for sports areas - Determination of angled ball behaviour - Tennis《运动场表面-成角度球特性的测定-网球》.pdf

1、BS EN 13865:2017Surfaces for sports areas Determination of angled ballbehaviour TennisBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 13865:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 13865:2017. It supersedes BS E

2、N 13865:2003 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/57, Surfaces for sports areas.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necess

3、ary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 90762 3 ICS 97.220.10Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard wa

4、s published under the authority of the Standards Policy and Strategy Committee on 31 March 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 13865:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13865 March 2017 ICS 97.220.10 Supersedes EN 13865:2003Englis

5、h Version Surfaces for sports areas - Determination of angled ball behaviour - Tennis Sols sportifs - Dtermination du comportement du rebond angulaire dune balle - Tennis Sportbden - Bestimmung des winkligen Ballverhaltens - Tennis This European Standard was approved by CEN on 3 February 2017. CEN m

6、embers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applic

7、ation to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Mana

8、gement Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvi

9、a, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Aven

10、ue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13865:2017 EBS EN 13865:2017EN 13865:2017 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Principle . 4 4 Apparatus .

11、 4 5 Test pieces . 5 6 Conditioning and test temperature 5 6.1 Laboratory tests . 5 6.2 On-site tests . 5 7 Preparation of tennis balls 5 7.1 Conditioning 5 7.2 Pre-compression . 5 8 Procedure. 5 9 Calculation and expression of results 6 10 Test report . 7 BS EN 13865:2017EN 13865:2017 (E) 3 Europea

12、n foreword This document (EN 13865:2017) has been prepared by Technical Committee CEN/TC 217 “Surfaces for sports areas”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement,

13、at the latest by September 2017 and conflicting national standards shall be withdrawn at the latest by September 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifyin

14、g any or all such patent rights. This document supersedes EN 13865:2003. In comparison with the previous edition, the following main modifications have been made: Figure 11 “Relationship between components of ball incidence and rebound“ has been replaced by a formula; the test procedure sequence has

15、 been updated; the temperature range for the on-site testing has been deleted. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic

16、, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

17、BS EN 13865:2017EN 13865:2017 (E) 4 1 Scope This European Standard specifies a method for the determination of the behaviour of a tennis ball striking a sports surface at an angle. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and ar

18、e indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12229, Surfaces for sports areas - Procedure for the preparation of synthetic turf and needle-punch

19、test pieces 3 Principle A ball is projected at an angle onto a sports surface and its velocity, angle and rebound are assessed. 4 Apparatus 4.1 Ball projector, providing a means of projecting a ball at a specified angle and velocity onto the surface without imparting spin greater than 3 rev/s. Suita

20、ble ball projection machines are available commercially. The release characteristics of the ball from the machine should be checked specifically (e.g. by stroboscopic photography) to ensure that spin in excess of 3 rev/s does not occur. 4.2 Ball track monitor, providing a means of monitoring the tra

21、ck of the ball before and after impact so that its velocity can be measured to an accuracy of 0,05 m/s and its angle of impact and rebound to 0,1. The uncertainty in the precision of the measuring technique shall be no greater than 2 %. NOTE The track of the ball can be monitored photographically or

22、 by timing its passage between light-sensitive receivers. In the latter case, the angle can be deduced from the vertical and horizontal components of velocity. 4.3 Balls in accordance with 4.3.2 are used in tests to demonstrate the conformity of a sports surface to a specification for the surface. 4

23、.3.1 Balls in accordance with 4.3.3 are used to demonstrate the performance of a particular type of ball on a given surface, e.g. a particular brand of ball to be used in a tournament. 4.3.2 At least three test tennis balls, taken from a pressurized ball canister, each covered with cloth weft compri

24、sing (45 5) % denier (6,67 dtex) polyamide and (55 5) % wool, and which, when tested in accordance with procedures detailed in the International Tennis Federation (ITF) Rules of Tennis, exhibit the following properties: Ball mass: (57,6 0,3) g; Ball diameter: (66,0 0,50) mm; Forward deformation: (6,

25、40 0,40) mm; BS EN 13865:2017EN 13865:2017 (E) 5 Return deformation (9,40 1,40) mm; Rebound (mean of five tests): (1,41 0,01) m. 4.3.3 When required, at least four commercially available tennis balls, taken from a pressurized ball canister, and which conform to the ITF Rules of Tennis. 4.3.4 Additio

26、nal balls of either type (see 4.3.2 or 4.3.3), if necessary, for trial runs (see 8.2). 5 Test pieces Test pieces of synthetic turf and textile sports surfaces shall be prepared in accordance with EN 12229. Test pieces of sports surfaces shall have a minimum length 500 mm and minimum width 500 mm, an

27、d shall be tested in combination with the supporting layers to be used in service and using the method of attachment recommended in the manufacturers instructions. Ensure the test piece is not warped or bowed. Loose laid test pieces shall be tested while anchored at the edges. Experience has shown t

28、hat it is extremely difficult to produce laboratory samples of mineral surfaces that have the same characteristics as actual facilities. Wherever possible, mineral surfaces should be tested in situ. 6 Conditioning and test temperature 6.1 Laboratory tests Condition test pieces for a minimum of 3 h a

29、t the specified test temperature. Unless stated otherwise in the product specification, the test temperature shall be (23 2) C. 6.2 On-site tests Tests on site shall be conducted at ambient temperature, with temperatures ranging from +10 C to +30 C, and at ambient humidity. 7 Preparation of tennis b

30、alls 7.1 Conditioning The balls shall be removed from their container at least 1 h prior to the test in order to ensure that they reach equilibrium with the prevailing ambient conditions. 7.2 Pre-compression The balls shall be subjected to a pre-compression procedure, as described in detail in the I

31、TF method, prior to being used in tests. 8 Procedure 8.1 Carry out all tests within 1 day of opening the ball canister (see 7.1). BS EN 13865:2017EN 13865:2017 (E) 6 8.2 Adjust the ball projector (see 4.1) to deliver a ball onto the test piece at an angle of incidence of (16 2) and a velocity of (30

32、 2) m/s, if necessary employing trial runs using additional balls (see 4.3.4). 8.3 Measure and record the temperature of the test surface area. 8.4 Project the first ball, onto the test piece surface and, using the ball track monitor (see 4.2), monitor and record the velocity and angle before and af

33、ter impact. 8.5 Slightly move the test equipment and repeat using next test ball ensuring the ball does not impact an area previously tested. Slightly move the test equipment and repeat using the third test ball. 8.6 Repeat the full sequence using each of the three balls a further two times so a tot

34、al of nine tests are made (three with each test ball) ensuring each test is on a new area of the surface. NOTE It is important that no ball is fired more than 10 times so as to avoid degradation of the ball. 8.7 If the surface has a directional pattern, such as the lay of the pile of synthetic turf,

35、 tests shall be made in the typical direction of play, i.e. parallel to the length of the court. 9 Calculation and expression of results From the monitoring of the ball before and after impact, obtain the angles and resultant velocities of incidence and rebound and for each test calculate the Court

36、Pace Rating using: ( ) ( )CPR=100 1- +a b-Te where the coefficient of restitution (COR) is given by: =fyiyethe coefficient of friction () (COF) is given by: ( )-=1+ix fxiyethe adjusted COR for temperature (eT) is given by: ( )= +c 23-Tee T and Vix= balls horizontal inbound velocity (m/s); Viy= balls

37、 vertical inbound velocity (m/s); Vfx= balls horizontal outbound velocity (m/s); Vfy= balls vertical outbound velocity (m/s); BS EN 13865:2017EN 13865:2017 (E) 7 T = mean temperature of test specimen (C); c = temperature coefficient (0,003); b = mean coefficient of restitution for all surface types

38、(0,81); a = pace perception constant (150). For each series of nine tests, calculate the mean values of coefficient of restitution and Court Pace Rating. 10 Test report The test report shall contain the following: a) reference to this European Standard, i.e. EN 13865:2017; b) complete identification

39、 of the surface tested, including the manufacturers reference and the type of supporting layers and their method of attachment; c) direction of test; d) test temperature; e) mean value of coefficient of restitution and mean value of Court Pace Rating; f) individual test results and Court Pace Rating

40、, if required; g) condition of the surface at the time of test, i.e. wet or dry. This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporat

41、ed by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standar

42、ds -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provid

43、e you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted Eu

44、ropean and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content

45、 in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Sa

46、ve for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing an

47、d using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that

48、only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format

49、 to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for