EN 13967-2012 en Flexible sheets for waterproofing - Plastic and rubber damp proof sheets including plastic and rubber basement tanking sheet - Definitions and characteristics (Inc.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 13967:2012Flexible sheets for waterproofing Plastic and rubber damp proof sheets including plastic and rubber basement tanking sheet Definitions and characteristicsBS EN 13

2、967:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 13967:2012.It supersedes BS EN 13967:2004+A1:2006, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee B/546, Flexible sheets for waterproofing and water vapour

3、control.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012.Published by BS

4、I Standards Limited 2012ISBN 978 0 580 75818 8 ICS 01.040.91; 91.100.50 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2012.Amendments issued since publi

5、cationDate T e x t a f f e c t e dBS EN 13967:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13967 April 2012 ICS 01.040.91; 91.100.50 Supersedes EN 13967:2004English Version Flexible sheets for waterproofing - Plastic and rubber damp proof sheets including plastic and rubber basement tank

6、ing sheet - Definitions and characteristics Feuilles souples dtanchit - Feuilles plastiques et lastomres empchant les remontes capillaires du sol - Dfinitions et caractristiques Abdichtungsbahnen - Kunststoff- und Elastomerbahnen fr die Bauwerksabdichtung gegen Bodenfeuchte und Wasser - Definitionen

7、 und Eigenschaften This European Standard was approved by CEN on 23 March 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bi

8、bliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the resp

9、onsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, G

10、reece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMU

11、NG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13967:2012: EBS EN 13967:2012EN 13967:2012 (E) 2 Contents page Foreword 41 Scope 52 Normative references 53 Terms and defi

12、nitions . 64 Product designation 75 Product characteristics . 75.1 General 75.2 Deviation from test sample dimensions 75.3 Visible defects 75.4 Dimensions and tolerances 75.5 Thickness and mass per unit area . 75.6 Water tightness 85.7 Resistance to impact . 85.8 Durability 85.9 Compatibility with b

13、itumen . 85.10 Resistance to tearing (nail shank) . 85.11 Joint strength . 85.12 Water vapour transmission properties 95.13 Resistance to static loading . 95.14 Tensile properties 95.15 Resistance to deformation under load 95.16 Reaction to fire . 95.17 Dangerous substances . 96 Evaluation of confor

14、mity . 106.1 General 106.2 Type testing 106.3 Factory production control (FPC) 107 Product data sheet and designation 138 Marking, labelling and packaging 13Annex A (informative) Product designation, typical materials and structure of sheets . 14Annex B (normative) Method of measuring the resistance

15、 of ventilating and draining damp-proof sheets to deformation under load . 15Annex C (informative) Example of product data sheet 19BS EN 13967:2012EN 13967:2012 (E) 3 Annex ZA (informative) Clauses of this European Standard addressing essential requirements or other provisions of EU Directives . 21B

16、ibliography 31BS EN 13967:2012EN 13967:2012 (E) 4 Foreword This document (EN 13967:2012) has been prepared by Technical Committee CEN/TC 254 “Flexible sheets for waterproofing”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either b

17、y publication of an identical text or by endorsement, at the latest by October 2012, and conflicting national standards shall be withdrawn at the latest by October 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or C

18、ENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13967:2004. The main technical changes are: For durability against chemicals, EN 1847:2009 of TC 254 is used instead of special Annex C. The minimum tolerance for the water vapour transmis

19、sion is fixed. The rules for mounting and fixing for reaction of fire testing are improved and the variation of products where results apply are fixed. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essent

20、ial requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. This European Standard is a general product standard for flexible sheets of plastics intended for damp proof sheets, including plastics basement tanking s

21、heets, for use in buildings. This standard is one of a series of product standards for factory made flexible sheets for use in buildings. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard:

22、Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the Unit

23、ed Kingdom. BS EN 13967:2012EN 13967:2012 (E) 5 1 Scope This document specifies definitions and characteristics of flexible plastic and rubber sheets which are intended to be used as damp proofing for buildings, including basement tanking. It specifies the requirements and test methods, and provides

24、 for the evaluation of conformity of the products with the requirements of this standard. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies.

25、For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1296, Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for roofing Method of artificial ageing by long term exposure to elevated temperature EN 1548, Flexible sheets for w

26、aterproofing Plastic and rubber sheets for roof waterproofing Method for exposure to bitumen EN 1847:2009, Flexible sheets for waterproofing Plastic and rubber sheets for roof waterproofing Methods for exposure to liquid chemicals, including water EN 1848-2, Flexible sheets for waterproofing Determi

27、nation of length, width, straightness and flatness Part 2: Plastic and rubber sheets for roof waterproofing EN 1849-2, Flexible sheets for waterproofing Determination of thickness and mass per unit area Part 2: Plastic and rubber sheets EN 1850-2, Flexible sheets for waterproofing Determination of v

28、isible defects Part 2: Plastic and rubber sheets for roof waterproofing EN 1928:2000, Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for roof waterproofing Determination of watertightness EN 1931, Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for roof wat

29、erproofing Determination of water vapour transmission properties EN 12310-1, Flexible sheets for waterproofing Part 1: Bitumen sheets for waterproofing Determination of resistance to tearing (nail shank) EN 12311-2, Flexible sheets for waterproofing Determination of tensile properties Part 2: Plasti

30、c and rubber sheets for roof waterproofing EN 12317-2, Flexible sheets for waterproofing Determination of shear resistance of joints Part 2: Plastic and rubber sheets for roof waterproofing EN 12691, Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for roof waterproofing Determin

31、ation of resistance to impact EN 12730:2001, Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for roof waterproofing Determination of resistance to static loading EN 13416:2001, Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for roof waterproofing Rules for

32、sampling EN 13501-1:2007+A1:2009, Fire classification of construction products and building elements Part 1: Classification using data from reaction to fire tests BS EN 13967:2012EN 13967:2012 (E) 6 EN 13859-1:2010, Flexible sheets for waterproofing Definitions and characteristics of underlays Part

33、1: Underlays for discontinuous roofing EN ISO 11925-2, Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test (ISO 11925-2) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13416:2001 a

34、nd the following apply. 3.1 sheet for damp proofing plastic or rubber sheet used on or under floors/ground slabs or in walls to prevent liquid water not under hydrostatic pressure passing from the ground into the internal environment 3.2 ventilating or draining damp proof sheet sheet conforming to t

35、he definition in 3.1 and with the ability to provide a continuous void or structure to allow free movement of water vapour or liquid water between the sheet and any further construction 3.3 tanking sheet sheet conforming to the definition in 3.1 used in wall construction or on or under floors or gro

36、und slabs to prevent liquid water under hydrostatic pressure passing from the ground into the internal environment or from one section of the structure to another 3.4 manufacturers limiting value MLV value stated by the manufacturer to be met during testing Note 1 to entry: The manufacturers limitin

37、g value can be a minimum value or a maximum value, according to statements made under product characteristics of this standard. 3.5 manufacturers declared value MDV value declared by the manufacturer accompanied by a declared tolerance 3.6 plastic sheet factory-made flexible sheet made from a plasti

38、c polymeric material and which may include composites of other materials 3.7 rubber sheet factory-made flexible sheet made from an elastomeric polymeric material and which may include composites of other materials 3.8 sampling procedure used to select or constitute a sample 3.9 sample sheet from whi

39、ch a test piece is taken BS EN 13967:2012EN 13967:2012 (E) 7 3.10 test piece part of the sample from which test specimens are taken 3.11 test specimen piece of precise dimensions taken from the test piece 3.12 batch amount of product continuously manufactured to the same specification 4 Product desi

40、gnation The types of damp proof sheets covered by this document are designated as follows: TYPE A damp proof sheet; TYPE V damp proof ventilating or draining sheet; TYPE T tanking sheet. 5 Product characteristics 5.1 General 5.1.1 Where a tolerance is specified by this document, it does not have to

41、be declared by the manufacturer. 5.1.2 When tested for purposes other than initial type testing or factory production control, the tests to determine product characteristics indicated in this document shall be started within 1 month of delivery from the manufacturer. 5.2 Deviation from test sample d

42、imensions Where the contours of the product make it impossible to obtain a test sample of the required dimensions, or otherwise render the test impracticable, testing may be carried out either on samples of different dimensions, or if still impracticable, on the equivalent flat sheet of the same thi

43、ckness as the finished product. Any such deviations from the test method shall be recorded on the test report and the product data sheet. 5.3 Visible defects The product shall be free of visible defects as determined in accordance with EN 1850-2. 5.4 Dimensions and tolerances The length, width and s

44、traightness shall be determined in accordance with EN 1848-2. The length and width shall lie within the declared tolerance of the manufacturers declared value (MDV). The maximum deviation from straightness shall not exceed 75 mm per 10 m length or shall be in the same proportion for other lengths (e

45、.g. 37,5 mm per 5 m length). 5.5 Thickness and mass per unit area The thickness and mass per unit area shall be determined in accordance with EN 1849-2. BS EN 13967:2012EN 13967:2012 (E) 8 Where a product is specified by mass per unit area, the mass shall lie within the declared tolerance of the man

46、ufacturers declared value. Where the dimensions of any profile are comparable to the area to be measured, a larger sample area shall be used and the deviation from the test method noted. Where a product is specified by thickness, the thickness shall lie within the declared tolerance of the manufactu

47、rers declared value. No single measurement shall lie outside the declared tolerance of the manufacturers declared value. 5.6 Water tightness The product shall be watertight as determined by Method A or B of EN 1928:2000 with a pressure of 2 kPa for Types A and V damp proof sheets and a pressure of 6

48、0 kPa for Type T damp proof sheets. 5.7 Resistance to impact Where required, the resistance to impact shall be determined in accordance with EN 12691 and the result shall be greater than or equal to the manufacturers limiting value. 5.8 Durability 5.8.1 Against ageing/degradation In order to verify

49、the artificial ageing behaviour of the product, watertightness shall be determined after exposure in accordance with EN 1296 for a period of 12 weeks. The watertightness shall be determined in accordance with EN 1928:2000 Method A or B. Type A and V damp proof sheets shall be tested at a pressure of 2 kPa and Type T tanking sheets at a pressure of 60 kPa, and shal