EN 13973-2002 en Rigid plastics containers - Method for determination of drainability《硬质塑料容器 排水能力测定方法》.pdf

1、BRITISH STANDARD Rigid plastics containers - Method for determination of drainability The European Standard EN 13973:ZOOZ has the status of a British Standard ICs 55.100; 55.140 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT JAW BS EN 13973:2002 British Standards BS EN 13973:2002

2、 Amd. No. National foreword Date Comments This British Standard is the official English language version of EN 139732002. The UK participation in its preparation was entrusted by Technical Committee PKWl5, Primary and transport packaging, to Subcommittee PKW/5/25, Rigid plastics packaging, which has

3、 the responsibility to: - - aid enquirers to understand the text; present to the responsible internationallEuropean committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them

4、in the UK. - A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “

5、International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with

6、 a British Standard does not of itself confer immunity from legal obligations. This British Standard, having been prepared under the direction of the Consumer Products and Services Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee

7、on 21 October 2002 Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 8, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. O BSI 21 October 2002 ISBN O 580 40

8、623 7 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 113973 October 2002 ICs 55.100; 55.140 English version Rigid plastics containers - Method for determination of drainability Conteneurs en plastique rigide - Mthode de dtermination de laptitude au vidage Formstabile Kunststoffbehlter - Verfah

9、ren zur Bestimmung der Entleerbarkeit This European Standard was approved by CEN on 19 August 2002 CEN members are bound to comply with the CENKENELEC Intemal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-

10、date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the

11、 responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland. Italy, Luxembourg,

12、 Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITI? EUROPEEN DE NORMALISATION EUROPISCHES KOMITEE FOR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels O 2002 CEN All rights of exploitation in any form and

13、by any means reserved worldwide for CEN national Members. Ref. No. EN 13973:2002 E EN 13973:2002 (E) Contents Page Foreword 3 Introduction . 4 1 Scope 5 2 Normative references 5 3 Terms and definitions 5 4 Principle 6 5 Sampling . 6 6 Apparatus . 6 7 Procedure . 6 8 Calculation 7 9 Test report 7 2 E

14、N 13973:2002 (E) Foreword This document EN 13973:2002 has been prepared by Technical Committee CENTTC 261 “Packaging“, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at

15、the latest by April 2003, and conflicting national standards shall be withdrawn at the latest by April 2003. According to the CENICENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Repub

16、lic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom, 3 EM 13973:2002 (E) D n trod uction The purpose of packaging is the containment, protection, distribution and promotion of pro

17、ducts. A major role is prevention of product damage and/or product waste. This European Standard was developed to test the design of a container and to provide requirements and test procedures to meet recommendations on residual product waste. 4 EN 139732002 (E) 1 Scope This European Standard specif

18、ies a method for determination on the drainability of plastic bottles and jars with a nominal capacity up to 5 I and of plastics canisters/jerricans with a nominal volume up to 20 I. NOTE Plastics bottles, jars, canisters and jerricans are referred to as “containers” in this standard. 2 Normative re

19、ferences This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of

20、 these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 13974, Rigid plastics containers - Specification of tolerance for dimensions, weight

21、and volume. 3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in EN 13974:2002 (some of which are repeated below for convenience) and the following apply. 3.1 plastics bottle rigid plastics container with shoulders and a small aperture, and generally

22、 blow moulded EN 13974:2002 3.2 plastics jar rigid plastics container of any base shape, with an aperture of area similar to that of the base EN 13974:2002 3.3 plastics canisterljerrican rigid plastics container with mostly rectangular or circular section NOTE An aperture on the top or side of the b

23、ody and a carrying device is usual. EN 13974:2002 3.4 nominal capacity capacity for which the container is designed 3.5 drainability quantitive measure of the residual content of a container emptied afer its normal use 3.6 absolute drainability the residual content of the test liquid expressed in g

24、5 EN 13973:2002 (E) 3.7 relative drainability the residual content expressed as a percentage of the nominal capacity 4 Principle Obtaining the mass of the chosen test liquid left as a residue in the container after drainage under gravity. 5 Sampling The test shall be performed on a predetermined num

25、ber of containers which shall be representative of the consignment. 6 Apparatus 6.1 Balance Balance with an accuracy of at least 0,l YO of the weight being measured. 6.2 Thermometer Thermometer with a scale range graduated in increments of no more than 1 “C, with an accuracy of f I “C. 6.3 Testing l

26、iquids 6.3.1 Normal tap water Normal tap water, not distilled and without any additional additives, with temperature of 23 “C f 1 “C. 6.3.2 Another test liquid Another test liquid of choice with defined characteristics. 6.4 Holding device for the container Holding device for the container, which wil

27、l enable 7.7 to be carried out if required. 7 Procedure 7.1 Place the empty container with its normal closure on the balance (6.1) and record its mass in g. 7.2 Fill the container to at least 50 % of its nominal capacity with the test liquid (6.3) and close the container. 7.3 Remove any liquid from

28、the outside surface of the container. 6 EN 13973:2002 (E) 7.4 Agitate the container to ensure that the entire inner surface is exposed to the liquid. 7.5 Open the container and empty it unti; the liquid flow stops. 7.6 Slowly incline the container up to the angle which ensures optimal draining. Leav

29、e the container in this position for a further 1 min without moving or shaking it. . 7.7 Re-weigh the emptied container with its closure and record the mass in g. 8 Calculation 8.1 Absolute drainability Calculate the absolute drainability, in g, by subtracting the mass of the empty container (7.1) f

30、rom the mass of the container after emptying (7.7). 8.2 Relative drainability Calculate the relative drainability, in %, from the ratio of absolute drainability to nominal capacity (the mass of the test liquid, in g) multiplied by 100. 9 Testreport The test report shall include the following informa

31、tion: a) a reference to this European Standard; b) a description of the container (.e. design, name, supplier etc.) and type of plastics material; c) the date of the test; d) the number of replicates tested; e) the nominal capacity of the container; 9 the cavity number, if applicable; g) the chosen

32、test liquid, together with its characteristics; h) the test temperature; i) the absolute drainability of each container; j) the relative drainability of each containers tested; k) the average absolute drainability of all container tested; I) the average relative drainability of all containers tested

33、; 7 EN 13973:2002 (E) m) a report on the sampling procedure used; n) the name and signature of the person conducting the test. 8 BS EN 13973:2002 BSI 389 Chiswick High Road London w4 4AL -a“Tw- a&- 21BXx2%mexm,-s BSI - British Standards Institution BSI is the independent national body responsible fo

34、r preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or

35、editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on th

36、e inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publ

37、ications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at httd/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those

38、that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services

39、are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase pr

40、ice of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: mernbershiflbsi-. Information regarding online access to British Standards via British Standards Online can be found at httD:/www.bsi-lbsonline. Fur

41、ther information about BSI is available on the BSI website at httD:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents A

42、ct 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary

43、details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-. A