EN 1462-2004 en Brackets for Eaves Gutters - Requirements and Testing《檐沟撑架 要求和检验》.pdf

1、BRITISH STANDARDBS EN 1462:2004Brackets for eaves gutters Requirements and testingThe European Standard EN 1462:2004 has the status of a British StandardICS 91.060.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53

2、g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 1462:2004This British Standard was published under the authority of the Standards Policy and Strategy Committee on 2 September 2005 BSI 2 September 2005ISBN 0 580 46240 4National forewordThis British Standard is the official Eng

3、lish language version of EN 1462:2004. It supersedes BS EN 1462:1997 which is withdrawn. Together with BS EN 12200-1:2000 and BS EN 607:1996, it will replace BS 4576-1:1989 which is scheduled for withdrawal September 2007.This new edition incorporates changes taking account of UK objections with the

4、 original version. It specifies both eaves and rafter brackets for use with gutters manufactured to EN 607 Eaves gutters and fittings made of PVC-U Definitions, requirements and testing and EN 612 Eaves gutters with bead stiffened fronts and rainwater pipes with seamed joints made of metal sheet. Ho

5、wever, roll fronted (bead stiffened) metal gutters of the type specified in EN 612 are not generally used in the UK and stronger brackets than those specified in EN 1462 are required for use with the heavier UK metal gutters.The UK participation in its preparation was entrusted by Technical Committe

6、e PRI/88, Plastics piping systems, to Subcommittee PRI/88/1, Plastics piping systems for non-pressure applications, which has the responsibility to:A list of organizations represented on this subcommittee can be obtained on request to its secretary.This publication does not purport to include all th

7、e necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the

8、 interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 14, an inside back cover and

9、 a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1462September 2004ICS 91.060.20 Supersedes EN 1462:1997English versionBrackets for

10、eaves gutters - Requirements and testingCrochets de gouttires pendantes - Exigences et mthodesdessaiRinnenhalter fr Hngedachrinnen - Anforderungen undPrfungThis European Standard was approved by CEN on 15 July 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipu

11、late the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exist

12、s in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies

13、of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STAND

14、ARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2004 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1462:2004: EEN 1462:2004 (E) 2Contents pageForeword31 S

15、cope 42 Normative references 43 Terms and definitions .54 Materials .55 Resistance to corrosion66 Design .76.1 General76.2 Load bearing capacity.76.3 Holes for fastenings 87 Designation of gutter brackets for ordering purposes8 8 Marking .89 Production control.9Annex A (normative) Test method to det

16、ermine the corrosion resistance of plastic-coated gutter brackets 10A.1 Principle10A.2 Apparatus .10A.3 Procedure .10Annex B (normative) Test method to determine the load bearing capacity of gutter brackets12 B.1 Principle12B.2 Apparatus .12B.3 Procedure .12EN 1462:2004 (E) 3Foreword This document (

17、EN 1462:2004) has been prepared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous laying and products for wall cladding”, the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical

18、text or by endorsement, at the latest by March 2005, and conflicting national standards shall be withdrawn at the latest by March 2005. This document supersedes EN 1462:1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound

19、to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United

20、Kingdom. EN 1462:2004 (E) 41 Scope This document specifies the requirements for rafter and fascia board brackets intended to support eaves gutters conforming to EN 607 or EN 612. 2 Normative references The following referenced documents are indispensable for the application of this document. For dat

21、ed references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 485-1, Aluminium and aluminium alloys Sheet, strip and plate Part 1: Technical conditions for inspection and deliveryEN 485-2, Aluminium and alu

22、minium alloys Sheet, strip and plate Part 2: Mechanical propertiesEN 485-3, Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form for hot-rolled productsEN 485-4, Aluminium and aluminium alloys Sheet, strip and plate Part 4: Tolerances on shape and dimen

23、sions for cold-rolled productsEN 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3: Chemical compositionEN 607, Eaves gutters and fittings made of PVC- U Definitions, requirements and testingEN 612, Eaves, gutters and rainwater down-pipes of metal sheet D

24、efinitions, classifications and requirementsEN 754-1, Aluminium and aluminium alloys Cold drawn rod/bar and tube Part 1: Technical conditions for inspection and deliveryEN 755-1, Aluminium and aluminium alloys Extruded rod/bar, tube and profiles Part 1: Technical conditions for inspection and delive

25、ryEN 1652, Copper and copper alloys Plate, sheet, strip and circles for general purposesEN 1676, Aluminium and aluminium alloys Alloyed ingots for remelting SpecificationsEN 1706, Aluminium and aluminium alloys Castings Chemical composition and mechanical propertiesEN 10025, Hot rolled products of n

26、on-alloy structural steels Technical delivery conditionsEN 10088-2, Stainless steels Part 2: Technical delivery conditions for sheet/plate and strip for general purposesEN 10088-3, Stainless steels Part 3: Technical delivery conditions for semi-finished products, bars, rods and sections for general

27、purposesEN 10111, Continuously hot-rolled low carbon steel sheet and strip for cold forming Technical delivery conditionsEN 10142, Continuously hot-dip zinc coated low carbon steels strip and sheet for cold forming Technical delivery conditionsEN 1462:2004 (E) 5EN 10215, Continuously hot-dip alumini

28、um-zinc (AZ) coated steel strip and sheet Technical delivery conditions EN 10326, Continuously hot-dip coated strip and sheet of structural steels Technical delivery conditions EN 10327, Continuously hot-dip coated strip and sheet of low carbon steels for cold forming Technical delivery conditions E

29、N ISO 1461, Hot dip galvanized coatings on fabricated iron and steel articles Specifications and test methods (ISO 1461:1999)3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1rafter bracket type of gutter bracket used for fixing a gutter to a ra

30、fter 3.2fascia bracket type of gutter bracket used for fixing a gutter to a fascia 4 Materials Gutter brackets shall be manufactured from one of the following materials: mild steel conforming to EN 10025 or EN 10111; hot-dip zinc coated steel sheet with a minimum grade of DX 51 D and a minimum coati

31、ng mass of 275 g/m2, conforming to EN 10142; zinc-aluminium coated steel sheet with a minimum grade of DX 51 D+ZA and a minimum coating mass of 225 g/m2, conforming to EN 10326 or EN 10327; aluminium-zinc coated steel sheet with a minimum grade of DX 51 D+AZ and a minimum coating mass of 150 g/m2, c

32、onforming to EN 10215; stainless steel conforming to EN 10088-2 or EN 10088-3; copper conforming to EN 1652; aluminium or aluminium alloy for sheet rolled products conforming to EN 485-1, EN 485-2, EN 485-3 or EN 485-4 in any grade of the 1000, 3000, 5000 and 6000 series; aluminium or aluminium allo

33、y for wrought products conforming to EN 754-1 or EN 755-1, and in composition conforming to EN 573-3 (with the exception of those alloys having a mass content of more than 0,3 % of copper or more than 3 % of magnesium); aluminium or aluminium alloy for castings conforming to EN 1706 and EN 1676; unp

34、lasticized polyvinyl chloride (PVC-U) conforming to the requirements given in EN 607 for injection moulded fittings. EN 1462:2004 (E) 65 Resistance to corrosion 5.1 Gutter brackets of mild steel conforming to EN 10025 or EN 10111 shall be protected from corrosion by one of the following means: a) Ho

35、t-dip galvanising conforming to EN ISO 1461. Zinc coatings shall conform to the minimum values given in Table 1. b) Flexible plastic coating, 60 m thick, over a zinc coating with an average thickness of 20 m. c) Flexible plastic coating, 60 m thick, with a suitable substrate. When tested in accordan

36、ce with Annex A, the plastic-coated bracket shall not exhibit any signs of rust or loosening of the coating from the steel. Table 1 Minimum zinc coating for mild steel brackets hot-dip galvanized after manufacture Thickness of coating Steel thickness of bracket (mm)Minimum single value (m) Average v

37、alue (m) 6 70 85 6 3 55 70 3 1,5 45 55 5.2 Gutter brackets of PVC-U shall meet the artificial ageing and colour-fastness requirements detailed in EN 607.5.3 Gutter brackets shall be manufactured from corrosion-resistant materials according to whether they are intended for use in aggressive atmospher

38、es (Class A industrial pollution or maritime) or more benign conditions (Class B), as given in Table 2. EN 1462:2004 (E) 7Table 2 Classes of resistance to corrosion Material of manufactureClass of resistance to corrosionStainless steel, copper, rolled or wrought aluminium or mild steel coated in acc

39、ordance with 5.1 a) or b) ACast aluminium conforming to EN 1706, with a corrosion resistance grading of A to C inclusive ACast aluminium conforming to EN 1706, corrosion resistance coated in accordance with 5.1c) APVC-U, conforming to EN 607 A Uncoated cast aluminium conforming to EN 1706, with a co

40、rrosion resistance of grade D BMild steel conforming to EN 10025 or EN 10111, coated in accordance with 5.1c), or hot-dip coated mild steel conforming to EN 10142, EN 10326, EN 10327 or EN 10215 B6 Design 6.1 General Gutter brackets shall be of such dimensions that the gutters of the shape and size

41、for which they are designed can slide freely through them. It shall not be possible for gutters to be lifted out of a bracket by strong wind. This shall be achieved either through the design of integral lugs or nibs on the bracket itself or by providing separate clips or springs to attach the gutter

42、 to the bracket. Clips and springs are not required to be of the same material as the bracket to which they are attached, but shall have a corrosion resistance of Class A, as given in Table 2, if attached to a gutter bracket of corrosion resistance Class A. Clips and springs shall be manufactured fr

43、om one of the following materials: any of the materials specified in Clause 4; polyamide plastic; galvanized and prepainted steel sheet having an average coating mass of not less than 275 g/m2.Where both the clip or spring and the gutter bracket are manufactured from metal, care shall be taken to av

44、oid contact between incompatible metals, thereby reducing the risk of electrolytic corrosion. 6.2 Load bearing capacity Gutter brackets shall be divided into three classes according to their load bearing capacity. When tested in accordance with Annex B, brackets of 80 mm or greater top opening width

45、 (i.e. brackets of Classes H and L) shall support the loads given in Table 3 without collapse and without causing permanent deflection exceeding 5 mm at the outer end of the bracket. EN 1462:2004 (E) 8Table 3 Load bearing Classes ApplicationTest load (N)Load bearing ClassBrackets for heavy duty 750

46、H Brackets for light duty 500 L Brackets for gutters below 80 mm top opening width O6.3 Holes for fastenings Rafter brackets shall have not less than two holes for fastenings. Where these brackets are designed to be fixed either by nails or screws, the holes shall not be less than 12 x (hole diamete

47、r) apart. Where the bracket is designed to be fixed only by screws, the holes shall not be less than seven diameters apart and the bracket shall be marked “S”. Fascia brackets of the heavy-duty load-bearing Class H shall have not less than two holes for fastenings. When these holes are one above the

48、 other on the vertical centre line of the bracket, they shall be not less than four diameters apart. When the holes are on each side of the centre line and in the same horizontal plane, they shall be not less than seven diameters apart. When the holes are on each side of the centre line but at diffe

49、rent levels, they shall be not less than five diameters apart. Fascia brackets of the light duty load-bearing Class L shall either have a single hole on the vertical centre line of the bracket or have the same arrangement and spacing of holes for fastenings as for fascia brackets of load-bearing Class H. All holes shall have a minimum diameter of 5 mm, after application of any corrosion resistance coating. Minimum diameter spacings between holes shall be measu