EN 1543-1998 en Products and Systems for the Protection and Repair of Concrete Structures - Test Methods - Determination of Tensile Strength Development for Polymers《混凝土结构的保护和修理用产品.pdf

1、 - - STD-BSI BS EN L543-ENGL 1998 Lb24bbl 0735447 29T M BRITISH STANDARD Products and systems for the protection and repair of concrete structures - Test methods - Determination of tensile strength development for polymers * * m The European Standard EN 1543A998 has the status of a British Standard

2、ICs 91.080.40; 91.100.30 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGH LAW BS EN 1543:1998 STD-BSI BS EN L5q3-ENGL L998 W lb2qbb9 735LiYB 12b = direction of the Sector AmdNo. Committee for Builing and Cid Engineering, was published under the authority of the Standards Committee a

3、nd comes into effect on 16 November 1998 Q BSI 1998 BS EN 1643:1998 Date Text affected National foreword This Brim Standard is the English language version of EN 1543:1!398. No existing standard is superseded The UK participation in its prepdon was entsusted by Technical committee M17, Concrete, to

4、Subcommittee B/517/8, Repair and protection of concrete structures, which has the responsibility to: - aid enquirem to understand the text; - present to the responsible European committee any enquiries on the - monitor related internationai and European developments and promu them in the UK. A list

5、of organizationS represented on this subcommittee can be obtained on request to its secrebty. Cross-references The British Stanards which implement intemational or European pubiications referred to in this document may be found in the BSI !3andards catalogue under the section entitied “international

6、 standards Correspondence index“, or by using the Find“ facility of the BSI standards Electronic catalogue. A British Standard does not purport to include all the necessary provisions of a contract Users of British Standards are responsible for their correct appication. Compliance with a British Sta

7、ndard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside hnt cover, the EN titie page, pages 2 to 7 and a back cover. ISBN O 580 297 9 I I STD-BSI BS EN 1SLi3-ENGL 1998 E 1b24bb7 0735447 Ob2 B EUROPEAN STANDARD EN 1543 NORME E

8、UR0PEE”E EUROP NORM January 1998 ICs 91.080.40 Desniptors: Concrete structures, repairs, protedion, materiais, polymers, materials, polymers, epoxy resins, products for conrete construction, tests, determination, tensile - the testing machine shall be equipped with a temperature controlled cabinet w

9、hich allows the maintenance of a constant temperature from (5 f i) OC to (21 f 2) OC, or other temperatures, providing all parties concerned agree. 3.2 Apparatus a) Testing machine (see annex A), by means of a centric tensile test at a deformation rate of 0,l mm/min, b) stopwatch. The development of

10、 strength is measured with the apparatus shown in Fgure 1. The apparatus consists of at least six rnouls cavities and pistons as dimensioned in Figure 1. The upper fhng device shall be constructed with universal joints in the tensile rod. All parts shaii be made of steel. The mould has a depth of 20

11、0,05 mm and a diameter of 25+y mm (see Figure 2). The piston shall have a diameter of 25-:,05 mm (we Figure 3). 3.3 Materials %o component epoxy resins or other, as specified. O BSI 1998 STD-BSI BS EN 1543-ENGL 199B W Lb24bb7 0735452 b57 = Page 4 EN 1543:1998 VI n a “1 O BSI 1998 STD-BSI BS EN 1543-

12、ENGL 1978 m lb2i.lbb7 O735453 593 Page 6 EN 1643:1998 NI0 / .$ O oi N N - - 07 T .e. I . 6N I Dimensions in mm Figure 2 - Mould O BSI 1998 STDWBSI BS EN 1543-ENGL 1778 E 1bZLibb7 0735Y5Li Li2T m Page 6 EN 1683:1998 P -1 Dimensiona in mm Figure 3 - Piston 4 Iiest procedure for the determination of th

13、e development of strength 4.1 Preparation of the resin The two components shall be prepared in accordance withthetechnical * data sheet of the manufacturer of the product. The two component resins and the test apparatus shall be maintained at the selected test temperahre for a minimum of 24 h before

14、 mixing the resins. The designated for the tests are (5 f 1) OC, x2i f 2) “c, but other suaable te- may be selected providing ali parties concerned agree. 4.2 Mixing The base and harener components shall be carefully mixed together, by means of a slowly rotating electric stjrrer and paddie, in accor

15、dance with the mandaclmers recommendations. To complete the mixing process, the resin shall be poured from one can to another and mixed again for 30s. Start the stopwatch at the end of the mixing. 4.3 Preparation of the moulds The cavity of the mould and the faces of the piston shall be abraded to p

16、rovide a mechanical key. To prevent adhesion of excess of resin, the upper face of the mould plate shall be lightly smeared with a release agent 4.4 Cleaning of the piston and of the rising main Remaining resin at the piston shali be removed by solvent (e.g. 70 % dichioromethane, 20 % formic acid, 1

17、0% tsichlorethyene) or other suitable solvent. 4.5 Filling the moulds Immediately aRermixing, the resin shali be poured into a2mm deep, 25mm diameter recess to ii up about1 The piston shall then be carefully lowered into position until its shoulder rests upon the upper face of the mould plate displa

18、cing excess resin through the centrai hole. storing and testing of the prepared specimen shaii be done at the same ternpentwe as described in 4.1. O BSI 1998 * * vi STD-BSI BS EN LSiI-ENGL 1998 1624bb9 0735455 3bb Page 7 EN 1543A998 5 Measurement of the development of strength Bibliography The time

19、of cure shail be measured from the completion of the mixing. For the validity of the test, it is necessary to get at least six correct results at each temperature. At various ages of cure, the resin mould and piston shali be fixed to the tensile machine and the tensile strength measured, a tensile l

20、oad is applied until fdure OCCUIS. The velocity of the defonnation is 0,l mmmin. The maximum value of the tensile force shail be recorded. The tensile strength shali be calculated in relation to the surface area of the piston The time intervai between tests shall be austed to give a spread of at lea

21、st siu resuits withjn the range O N/m2 to 5,O N/m2 (one below 1 Nimm2 and one above 5 Nhnm2). Annex A (informative) i Requimts for machines for tension and mp - reference to this European standard, - the date and place of sampling and testing - the temperature of testing; - the mixjng time; - a plot

22、 of tensile strength against cure time for each test temperature; - the rate of development of strength of 3 N/mm2; - the diameter and depth of each mould - the interpolated cure time in minutes to reach a tensile strength of 3 N/mm2. o BSI 1998 BS EN 1643:1998 BSI 389 Chiswick High Road London w4 4

23、AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revisio

24、n. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to impmve the quaiity of our products and services. We would be grakfd if anyone ning an inaccuracy or ambiguity while using this British Standard would inform the Secret

25、ary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 0181 996 9ooo. Fax: 0181 996 7400. BSI offers members an individuai updating service ded PLUS which ensures that subscribers automatidy receive the latest editions of standards. Buying stan

26、dards Orders for all BSI, intedonai and foreign standards publications should be addressed to Customer Services. Tel: 0181 996 7000. Fax 0181 996 7001. in response to orders for intemationai standards, it is BSI policy to supply the BSI implementation of those that have been published as British Sta

27、ndars, unies otherwiserequ Information on standards BSI pmvides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information seMces are also avaiiable which give details on ali its pr

28、oducts and services. Contact the Information Centre. Tel: 0181 996 7111. Fax 0181 996 7048. Subscribii members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Adnkk

29、tmh on. Tel: 0181 996 7002. Fax 0181 996 7001. COPyniBht Copyright subsists in ali BSI publications. BSI also holds the copyright, in the K, of the publications of the intemational standardization bodies. Except as permiaed under the Copyright, Designs and Patents Act 1988 no extract may be reproduc

30、ed, stored in a retrievai system or tsansmiaed in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the stanard, of necessary details such as symbols, and size, t

31、ype or grade designaions. If these details are to be used for any other purpose than implementation then the prior written pennission of BSI must be obtained If permission is granted, the tem may include royalty payments or a licensing agreement Details and advice can be obtained from the copyright Manager. Tel: 0181 996 7070.